IMAGRAPH CORPORATION
IMASCAN CRHOMA/VL, IMASCAN MONO/MONO-D/VL, IMASCAN RGB/RGB-D/VL
|
Card Type |
Video |
|
Chip Set |
Tseng Labs ET4000/W32 |
|
Maximum Onboard Memory |
2MB DRAM (Memory configuration on the Imascan Mono/Mono-D/VL is unidentified) |
|
Data Bus |
32-bit VESA Local Bus |
|
Video Types Supported |
XVGA |
|
Highest Resolution Supported |
1280 x 1024 |
|
CONNECTIONS | |||
|
Function |
Label |
Function |
Label |
|
VGA Out |
J1 |
Daughter board connector |
J4 |
|
Capture video in |
J2 |
Daughter board connector |
J5 |
|
VGA feature connector |
J3 | ||
|
Note: The exact # of pins on J5 is unidentified. | |||
|
USER CONFIGURABLE SETTINGS | |||
|
Setting |
Label |
Position | |
|
IRQ 2/9 enabled |
JP1 |
Pins 1 & 2 closed | |
|
Any IRQ disabled |
JP1 |
Pins 2 & 3 closed | |
|
CONNECTIONS | |||
|
Function |
Label |
Function |
Label |
|
Daughter board connector |
J1 |
Daughter board connector |
J6 |
|
Note: The exact # of pins on J6 is unidentified. | |||
|
CONNECTIONS | |||
|
Function |
Label |
Function |
Label |
|
Daughter board connector |
P1 |
Daughter board connector |
P5 |
|
Digital port |
P2 | ||
|
Note: The exact # of pins on P2 & P5 is unidentified. | |||
MONO/MONO-D DAUGHTER BOARD JUMPER CONFIGURATION
|
USER CONFIGURABLE SETTINGS | |||
|
Setting |
Label |
Position | |
|
Factory configured - do not alter |
J1 |
Unidentified | |
|
Factory configured - do not alter |
J2 |
Unidentified | |
|
Factory configured - do not alter |
J3 |
Unidentified | |
|
Factory configured - do not alter |
J4 |
Unidentified | |
|
Factory configured - do not alter |
J5 |
Unidentified | |
|
Factory configured - do not alter |
J6 |
Unidentified | |
|
Video1 75ohm termination enabled |
J7 |
Pins 1 & 2 closed | |
|
Video1 termination disabled |
J7 |
Pins 2 & 3 closed | |
|
Video2 75ohm termination enabled |
J8 |
Pins 1 & 2 closed | |
|
Video2 termination disabled |
J8 |
Pins 2 & 3 closed | |
|
Video3 75ohm termination enabled |
J9 |
Pins 1 & 2 closed | |
|
Video3 termination disabled |
J9 |
Pins 2 & 3 closed | |
|
Video4 75ohm termination enabled |
J10 |
Pins 1 & 2 closed | |
|
Video4 termination disabled |
J10 |
Pins 2 & 3 closed | |
|
Factory configured - do not alter |
J11 |
Unidentified | |
|
Factory configured - do not alter |
J12 |
Unidentified | |
|
Note: J1 - J3 sets the "Bus Select", J4 sets the "Field Invert", J5 & J6 sets the "Board Select", & J11 & J12 sets the "Termination". | |||
RGB/RGB-D DAUGHTER BOARD JUMPER CONFIGURATION
|
USER CONFIGURABLE SETTINGS | |||
|
Setting |
Label |
Position | |
|
Factory configured - do not alter |
J1 |
Unidentified | |
|
Factory configured - do not alter |
J2 |
Unidentified | |
|
Factory configured - do not alter |
J3 |
Unidentified | |
|
Factory configured - do not alter |
J4 |
Unidentified | |
|
Factory configured - do not alter |
J5 |
Unidentified | |
|
Factory configured - do not alter |
J6 |
Unidentified | |
|
Red1 75ohm termination enabled |
J7 |
Pins 1 & 2 closed | |
|
Red1 termination disabled |
J7 |
Pins 2 & 3 closed | |
|
Green1 75ohm termination enabled |
J8 |
Pins 1 & 2 closed | |
|
Green1 termination disabled |
J8 |
Pins 2 & 3 closed | |
|
USER CONFIGURABLE SETTINGS (CONT) | |||
|
Setting |
Label |
Position | |
|
Blue1 75ohm termination enabled |
J9 |
Pins 1 & 2 closed | |
|
Blue1 termination disabled |
J9 |
Pins 2 & 3 closed | |
|
Red2 75ohm termination enabled |
J10 |
Pins 1 & 2 closed | |
|
Red2 termination disabled |
J10 |
Pins 2 & 3 closed | |
|
Green2 75ohm termination enabled |
J11 |
Pins 1 & 2 closed | |
|
Green2 termination disabled |
J11 |
Pins 2 & 3 closed | |
|
Blue2 75ohm termination enabled |
J12 |
Pins 1 & 2 closed | |
|
Blue2 termination disabled |
J12 |
Pins 2 & 3 closed | |
|
Note: J1 - J3 sets the "Bus Select", J4 sets the "Field Invert", & J5 & J6 sets the "Board Select". | |||