ZOLTRIX, INC.
FM-VSP56I
|
Card Type |
Modem, Fax |
|
Chip Set |
Rockwell |
|
I/O Options |
Speaker out, microphone in |
|
Maximum Modem Rate |
56Kbps |
|
Maximum Fax Rate |
14.4Kbps |
|
Data Modulation Protocol |
Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.32, V.32bis, V.34, K56Flex |
|
Fax Modulation Protocol |
ITU-T V.17, V.27ter, V.29 |
|
Error Correction/Compression |
MNP5, MNP10, V.42, V.42bis |
|
Fax Class |
Class I |
|
Data Bus |
16-bit ISA |
|
Card Size |
Half-length, half-height card |
|
CONNECTIONS | ||||||
|
Function |
Label |
Function |
Label | |||
|
Line in |
CN1 |
Microphone in |
CN3 | |||
|
Line out |
CN2 |
Speaker out |
CN4 | |||
|
SERIAL PORT ADDRESS | |
|
Setting |
JP1 |
|
COM1 (3F8h) |
Pins 1 & 3, 2 & 4 closed |
|
COM2 (2F8h) |
Pins 3 & 5, 2 & 4 closed |
|
COM3 (3E8h) |
Pins 1 & 3, 4 & 6 closed |
|
COM4 (2E8h) |
Pins 3 & 5, 4 & 6 closed |
|
SUPPORTED COMMAND SET |
|
Basic AT Commands |
|
AT, A/ |
|
A, B, C, D, E, H, I, L, M, N, O, P, Q, T, V, W, X, Y, Z |
|
&C, &D, &F, &G, &J, &K, &L, &M, &P, &R, &S, &T, &W, &X, &Y, &Z |
|
Extended AT Commands |
|
\A, \B, \G, \K, \N, \V |
|
%C, %E, %L, %Q |
|
S Registers |
|
S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S24, S25, |
|
S26, S27, S28, S29, S30, S31, S32, S33, S37, S38, S39, S40, S41, S46, S82, S86, S91, S95 |
|
Special Commands |
|
+MS |
|
Note: See MHI Help File for full command documentation. |
Proprietary AT Command Set
|
COMMUNICATIONS MODE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Qn [cmds] |
|
Description: |
Selects communications mode options |
|
Command |
Mode |
|
&Q0 |
Asynchronous mode, serial port speed follows connect speed. |
| &Q5 |
Error correction mode |
|
&Q6 |
Buffered asynchronous mode |
|
CONFIGURATION PROFILES | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] &V [cmds] |
|
Description: |
Displays active and stored configuration profiles |
|
Command |
Function |
|
&V1 |
Displays statistics of previous connection |
S(Status) - Registers
|
AUTOSYNC HDLC ADDRESS SETTINGS | |
|
Type: |
Register |
|
Format |
AT [cmds] S20=n [cmds] |
|
Description: |
Controls the AutoSync HDLC address settings |
|
BIT-MAPPED AUTOSYNC OPTIONS | |
|
Type: |
Register |
|
Format |
AT [cmds] S19=n [cmds] |
|
Description: |
Controls the AutoSync configuration options |
|
ERROR CORRECTION NEGOTIATION | |
|
Type: |
Register |
|
Format |
AT [cmds] S36=n [cmds] |
|
Description: |
Selects the action of the modem if it fails to connect with the error-correction protocol set in &Q. |
|
Command |
Function |
|
S36=0 |
Hang up |
|
S36=1 |
Attempt a direct connection |
|
S36=2 |
Not used |
|
S36=3 |
Attempt a buffered connection |
|
S36=4 |
Attempt a connection at MNP2-4; if that fails, hang up. |
|
S36=5 |
Attempt a connection at MNP2-4; if that fails, attempt a direct connection. |
|
S36=6 |
Attempt a connection at MNP2-4; if that fails, hang up. |
|
í S36=7 |
Attempt a connection at MNP2-4; if that fails, attempt a buffered connection. |
|
FEATURE NEGOTIATION OPTIONS | |||
|
Type: |
Register | ||
|
Format: |
AT [cmds] S48=n [cmds] | ||
|
Description: |
Selects active error correction and compression protocols | ||
|
Command |
Function | ||
|
S48=0 |
Detection negotiation disabled, XID negotiation disabled | ||
|
í S48=7 |
Detection negotiation and XID negotiation enabled | ||
|
S48=128 |
Fall-back to options set in S36 | ||