IPTools.net.ua

Card Type

Modem (asynchronous)

Chipset

U.S. Robotics, Inc.

Maximum Data Rate

56Kbps

Maximum Fax Rate

14.4Kbps

Data Modulation

U.S. Robotics x2

Fax Modulation

ITU-T V.17, V.21CH2, V.27ter, V.29

Error Correction/Compression

MNP5, V.42, V.42bis

Fax Class

Class I & II

Data Bus

8-bit ISA

Card Size

Full height, one-third length

CONNECTIONS

Function

Label

Function

Label

Telephone line out

CN1

Telephone line in

CN2

USER CONFIGURABLE SETTINGS

Setting

Label

Position

í Plug-N-Play disabled

JP1/C

Closed

Plug-N-Play enabled

JP1/C

Open

SERIAL PORT ADDRESS SELECTION

Setting

JP1/A

JP1/B

3F8h (COM1:)

Closed

Closed

í 2E8h (COM2:)

Open

Closed

3F8h (COM3:)

Closed

Open

2E8h (COM4:)

Open

Open

Plug-N-Play

Open

Open

INTERRUPT SELECTION

Setting

JP2/A

JP2/B

JP2/C

JP2/D

JP2/E

2

Closed

Open

Open

Open

Open

í 3

Open

Closed

Open

Open

Open

4

Open

Open

Closed

Open

Open

5

Open

Open

Open

Closed

Open

7

Open

Open

Open

Open

Closed

Plug-N-Play

Open

Open

Open

Open

Open

SUPPORTED STANDARD COMMANDS

Basic AT Commands

+++, �comma�, A/

A, B, D, E, F, H, L, M, O, P, T, V, X, Z

&C, &D, &F, &G, &P, &R, &S, &T, &W

S-Registers

S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S18, S25, S38

BIT-MAPPED REGISTER S13

Format

AT [cmds] S13=n [cmds]

Default:

0

Range:

0 - 223

Description:

Controls DTR reset, DTR dialing, reset dialing, and MNP3.

Bit

Value

Function

0

í 0

1

Reset on low DTR.

1

í 0

1

Non-error-correcting mode transmit buffer set to 128 bytes.

2

í 0

1

Backspace and delete keys reversed.

3

í 0

1

DTR dialing enabled.

4

í 0

1

Reset dialing enabled.

5

0

Not used.

6

í 0

1

MNP 3 disabled.

7

í 0

1

Modem disconnects and enters command state when +++ is received.

BIT-MAPPED REGISTER S15

Format:

AT [cmds] S15=n [cmds]

Default:

0

Range:

0 - 511

Description:

Controls error correction and compression in selected protocols, MNP modes, and V.42 operation.

Bit

Value

Function

0

í 0

1

Error correction/compression disabled in V.22 mode.

1

í 0

1

Error correction/compression disabled in V.22bis mode.

2

í 0

1

Error correction/compression disabled in V.32 and V.32bis modes.

3

í 0

1

MNP handshake disabled.

4

í 0

1

MNP4 enabled.

5

í 0

1

MNP3 enabled.

6

í 0

1

MNP configured for non-compatible modems.

7

í 0

1

V.42 disabled.

8

í 0

1

V.42 detection phase disabled.

BIT-MAPPED REGISTER S27

Format:

AT [cmds] S27=n [cmds]

Default:

0

Range:

0 - 255

Description:

Controls V.21, V.32 encoding and modulation, V.32bis modulation, V.42 answer tone and selective reject, and 9600 result codes.

Bit

Value

Function

0

í 0

1

V.21 enabled.

1

í 0

1

V.32 trellis coding disabled.

2

í 0

1

V.32 modulation disabled.

3

í 0

1

2100Hz answer tone disabled.

4

í 0

1

Fallback to V.23 enabled.

5

í 0

1

V.32bis modulation disabled.

6

í 0

1

V.42 selective reject disabled.

7

í 0

1

Force 9600 result codes.

BIT-MAPPED REGISTER S32

Format:

AT [cmds] S32=n [cmds]

Default:

2

Range:

0 - 59

Description:

Controls V.8 protocol and options, and V.34 and x2 modulation protocols.

Bit

Value

Function

0

í 0

1

V.8 Call Indicate enabled.

1

í 1

V.8 enabled.

2

0

Not used.

3

í 0

1

V.34 modulation disabled.

4

í 0

1

V.34 modulation at 31.2Kbps and 33.6Kbps disabled.

5

í 0

1

U.S. Robotics x2 modulation disabled.

BREAK LENGTH

Type:

Register

Format:

AT [cmds] S21=n [cmds]

Default:

10

Range:

0 - 255

Unit:

10 ms

Description:

Sets the length of error correction mode breaks sent from DCE to DTE.

BREAK TYPE

Type:

Configuration

Format:

AT [cmds] &Yn [cmds]

Description:

Configures action of break signal.

Command

Function

&Y0

Break empties buffer.

í &Y1

Break empties buffer and is sent immediately.

&Y2

Break does not empty buffer and is sent immediately.

COMPRESSION MODE

Type:

Configuration

Format:

AT [cmds] &Kn [cmds]

Description:

Selects the type of data compression that will be used.

Command

Function

&K0

Data compression disabled.

í &K1

Auto-detect compression mode.

&K2

Data compression enabled.

&K3

MNP5 data compression only enabled.

CONNECTION SPEED LOWER LIMIT

Type:

Configuration

Format:

AT [cmds] &Un [cmds]

Description:

Sets slowest allowed connection speed if &N is set to 1 or higher.

Command

Function

&U0

No minimum connect speed.

&U1

Set minimum connect speed to 300bps.

&U2

Set minimum connect speed to 1200bps.

&U3

Set minimum connect speed to 2400bps.

&U4

Set minimum connect speed to 4800bps.

&U5

Set minimum connect speed to 7200bps.

&U6

Set minimum connect speed to 9600bps.

&U7

Set minimum connect speed to 12Kbps.

&U8

Set minimum connect speed to 14.4Kbps.

&U9

Set minimum connect speed to 16.8Kbps.

&U10

Set minimum connect speed to 19.2Kbps.

&U11

Set minimum connect speed to 21.6Kbps.

CONNECTION SPEED LOWER LIMIT (CON'T)

Command

Function

&U12

Set minimum connect speed to 24Kbps.

&U13

Set minimum connect speed to 26.4Kbps.

&U14

Set minimum connect speed to 28.8Kbps.

&U15

Set minimum connect speed to 31.2Kbps.

&U16

Set minimum connect speed to 33.6Kbps.

&U17

Set minimum connect speed to 33.3Kbps.

&U18

Set minimum connect speed to 37.3Kbps.

&U19

Set minimum connect speed to 41.3Kbps.

&U20

Set minimum connect speed to 42.6Kbps.

&U21

Set minimum connect speed to 44Kbps.

&U22

Set minimum connect speed to 45.3Kbps.

&U23

Set minimum connect speed to 46.6Kbps.

&U24

Set minimum connect speed to 48Kbps.

&U25

Set minimum connect speed to 49.3Kbps.

&U26

Set minimum connect speed to 50.6Kbps.

&U27

Set minimum connect speed to 52Kbps.

&U28

Set minimum connect speed to 53.3Kbps.

&U29

Set minimum connect speed to 54.6Kbps.

&U30

Set minimum connect speed to 56Kbps.

&U31

Set minimum connect speed to 57.3Kbps.

CONNECTION SPEED UPPER LIMIT

Type:

Configuration

Format:

AT [cmds] &Nn [cmds]

Description:

Sets required connection speed if &U is set to 0; otherwise, sets fastest allowed connection speed.

Command

Function

&N0

No maximum connect speed.

&N1

Set maximum connect speed to 300bps.

&N2

Set maximum connect speed to 1200bps.

&N3

Set maximum connect speed to 2400bps.

&N4

Set maximum connect speed to 4800bps.

&N5

Set maximum connect speed to 7200bps.

&N6

Set maximum connect speed to 9600bps.

&N7

Set maximum connect speed to 12Kbps.

&N8

Set maximum connect speed to 14.4Kbps.

&N9

Set maximum connect speed to 16.8Kbps.

&N10

Set maximum connect speed to 19.2Kbps.

&N11

Set maximum connect speed to 21.6Kbps.

&N12

Set maximum connect speed to 24Kbps.

&N13

Set maximum connect speed to 26.4Kbps.

&N14

Set maximum connect speed to 28.8Kbps.

&N15

Set maximum connect speed to 31.2Kbps.

CONNECTION SPEED UPPER LIMIT (CON'T)

Command

Function

&N16

Set maximum connect speed to 33.6Kbps.

&N17

Set maximum connect speed to 33.3Kbps.

&N18

Set maximum connect speed to 37.3Kbps.

&N19

Set maximum connect speed to 41.3Kbps.

&N20

Set maximum connect speed to 42.6Kbps.

&N21

Set maximum connect speed to 44Kbps.

&N22

Set maximum connect speed to 45.3Kbps.

&N23

Set maximum connect speed to 46.6Kbps.

&N24

Set maximum connect speed to 48Kbps.

&N25

Set maximum connect speed to 49.3Kbps.

&N26

Set maximum connect speed to 50.6Kbps.

&N27

Set maximum connect speed to 52Kbps.

&N28

Set maximum connect speed to 53.3Kbps.

&N29

Set maximum connect speed to 54.6Kbps.

&N30

Set maximum connect speed to 56Kbps.

&N31

Set maximum connect speed to 57.3Kbps.

DISPLAY HELP SCREEN - AMPERSAND

Type:

Configuration

Format:

AT [cmds] &$ [cmds]

Description:

Displays the help screen on the AT& commands.

DISPLAY HELP SCREEN - BASIC

Type:

Configuration

Format:

AT [cmds] $ [cmds]

Description:

Displays the basic help screen.

DISPLAY HELP SCREEN - DIAL

Type:

Configuration

Format:

AT [cmds] D$ [cmds]

Description:

Displays the help screen on the dialing commands.

DISPLAY HELP SCREEN - REGISTERS

Type:

Configuration

Format:

AT [cmds] S$ [cmds]

Description:

Displays the help screen for S registers.

DISPLAY INFORMATION

Type:

Immediate

Format:

AT [cmds] In [cmds]

Description:

Displays modem properties.

Command

Function

I0

Displays product identification code.

I1

Tests and displays ROM checksum result.

I2

Tests and displays RAM checksum result.

I4

Displays current command settings.

I5

Displays current NVRAM settings.

I6

Displays current connection�s statistics.

I7

Displays product configuration.

DISTINCTIVE RING

Type:

Register

Format:

AT [cmds] S41=n [cmds]

Description:

Selects whether the modem will use the Distinctive Ring function.

Command

Function

í S41=0

Distinctive ring abled.

S41=1

Distinctive ring enabled.

ERROR CORRECTION MODE

Type:

Configuration

Format:

AT [cmds] &Mn [cmds]

Description:

Selects active error correction protocols.

Command

Function

&M0

Normal mode only.

í &M4

Auto-detect mode.

&M5

Error correction mode only.

EXTENDED RESULT CODES

Type:

Configuration

Format:

AT [cmds] &An [cmds]

Description:

Selects extended result codes.

Command

Function

&A0

Extended result codes disabled.

&A1

Error correction result codes enabled.

&A2

V.32 result code enabled.

í &A3

Error correction and compression result codes enabled.

FLOW CONTROL CHARACTER - XOFF

Type:

Register

Format:

AT [cmds] S23=n [cmds]

Default:

19

Range:

0 - 127

Unit:

1 ASCII character

Description:

Sets the character used to represent XOFF.

FLOW CONTROL CHARACTER - XON

Type:

Register

Format:

AT [cmds] S22=n [cmds]

Default:

17

Range:

0 - 127

Unit:

1 ASCII character

Description:

Sets the character used to represent XON.

FLOW CONTROL - MODEM-TO-MODEM

Type:

Configuration

Format:

AT [cmds] &In [cmds]

Description:

Selects the type of modem-to-modem flow control used.

Command

Function

í &I0

Software flow control disabled.

&I1

XON/XOFF pass-through enabled.

&I2

XON/XOFF pass-through disabled.

FLOW CONTROL TYPE

Type:

Configuration

Format:

AT [cmds] &Hn [cmds]

Description:

Sets type of flow control used by modem.

Command

Function

&H0

Flow control disabled.

í &H1

CTS/RTS flow control enabled.

&H2

XON/XOFF flow control enabled.

&H3

CTS/RTS and XON/XOFF flow control enabled.

INACTIVITY TIMER

Type:

Register

Format

AT [cmds] S19=n [cmds]

Default:

0

Range:

0 - 255

Unit:

1 minute

Description:

Maximum duration of DTE and DCE inactivity allowed prior to initiating hang-up process.

LOCK SERIAL PORT

Type:

Configuration

Format:

AT [cmds] &Bn [cmds]

Description:

Sets operation of serial port speed.

Command

Function

&B0

Serial speed follows connect speed.

&B1

Serial speed locked.

í &B2

Serial speed locked in error correction mode only.

RESULT CODES

Type:

Configuration

Format:

AT [cmds] Qn [cmds]

Description:

Enables modem to send result codes to the DTE.

Command

Function

í Q0

Result codes enabled.

Q1

Result codes disabled.

Q2

Result codes enabled in originate mode only.

TONE DIALING TEST

Type:

Register

Format:

AT [cmds] S16=n [cmds]

Description:

Begins a tone dialing test.

Command

Function

í S16=0

Tone dialing test disabled.

S16=2

Tone dialing test enabled.

V.21 ANSWER MODE FALLBACK TIMER

Type:

Register

Format:

AT [cmds] S29=n [cmds]

Default:

20

Range:

Unidentified

Unit:

.1 second

Description:

The function of this register is unidentified.

V.32 HANDSHAKE TIME

Type:

Register

Format:

AT [cmds] S28=n [cmds]

Default:

8

Range:

0 - 255

Unit:

.1 second

Description:

Sets length of V.32 handshake. A value of 255 means that the modem will only accept connections with V.32 at 9600bps.

V.34 MAPPING

Type:

Register

Format:

AT [cmds] S34=n [cmds]

Default:

0

Range:

0 - 15

Description:

Controls V.34 mapping, non-linear coding, transmit level deviation, pre-emphasis, and pre-coding.

Bit

Value

Function

0

í 0

1

8S-2D map disabled.

1

í 0

1

16S-4D map disabled.

2

í 0

1

32S-2D map disabled.

3

í 0

1

64S-4D map disabled.

4

í 0

1

Non-linear coding disabled.

5

í 0

1

Transmit level deviation disabled.

6

í 0

1

Pre-emphasis disabled.

7

í 0

1

Pre-coding disabled.

V.34 OPTIONS

Type:

Register

Format:

AT [cmds] S33=n [cmds]

Default:

0

Range:

0 - 255

Description:

Controls V.34 baud rate and shaping.

Bit

Value

Function

0

í 0

1

2400 baud rate disabled.

1

í 0

1

2743 baud rate disabled.

2

í 0

1

2800 baud rate disabled.

3

í 0

1

3000 baud rate disabled.

4

í 0

1

3200 baud rate disabled.

5

í 0

1

3429 baud rate disabled.

6

0

Not used.

7

í 0

1

Shaping disabled.