UNIQUE HARDWARE CO., LTD.
FAXSENGER 34
|
Card Type |
Modem (synchronous/asynchronous) |
|
Chipset |
Unidentified |
|
Maximum Data Rate |
28.8Kbps |
|
Maximum Fax Rate |
14.4Kbps |
|
Data Modulation |
Bell 103A, 212A ITU-T V.21, V.22, V.22bis, V.32, V.32bis, V.34 Rockwell V.FC |
|
Fax Modulation |
ITU-T V.17, V.21CH2, V.27ter, V.29 |
|
Error Correction/Compression |
MNP5, V.42, V.42bis |
|
Fax Class |
Class I & II |
|
Data Bus |
Serial |
|
CONNECTIONS | |||
|
Function |
Label |
Function |
Label |
|
4 AA alkaline cells (on bottom) |
BAT |
DC power in |
CN4 |
|
Serial port |
CN1 |
Telephone line out |
CN5 |
|
Serial port |
CN2 |
Power switch |
SW1 |
|
DC power in |
CN3 | ||
|
DIAGNOSTIC LED(S) | |||
|
LED |
Color |
Status |
Condition |
|
288 |
Green |
On |
Modem connected at 28.8Kbps |
|
288 |
Green |
Off |
Modem connected at slower than 28.8Kbps |
|
144 |
Green |
On |
Modem connected at 14.4Kbps or faster |
|
144 |
Green |
Off |
Modem connected at slower than 14.4Kbps |
|
EC |
Green |
On |
Error correction enabled |
|
EC |
Green |
Off |
Error correction disabled |
|
LBAT |
Green |
On |
Batteries are low |
|
LBAT |
Green |
Off |
Batteries are good |
|
AA |
Green |
On |
Auto-answer enabled |
|
AA |
Green |
Off |
Auto-answer disabled |
|
AA |
Green |
Blinking |
Phone is ringing |
|
CD |
Green |
On |
Carrier signal detected |
|
CD |
Green |
Off |
Carrier signal not detected |
|
OH |
Green |
On |
Modem is off-hook |
|
OH |
Green |
Off |
Modem is on-hook |
|
OH |
Green |
Blinking |
Modem is dialing in pulse mode |
|
DIAGNOSTIC LED(S) (CON'T) | |||
|
LED |
Color |
Status |
Condition |
|
SD |
Green |
On |
Modem is transmitting data |
|
SD |
Green |
Off |
Modem is not transmitting data |
|
RD |
Green |
On |
Modem is receiving data |
|
RD |
Green |
Off |
Modem is not receiving data |
|
TR |
Green |
On |
DTR signal is high |
|
TR |
Green |
Off |
DTR signal is low |
|
PWR |
Green |
On |
Power is on |
|
PWR |
Green |
Off |
Power is off |
|
FAX/TM |
Green |
On |
Modem is connected in FAX mode |
|
FAX/TM |
Green |
Blinking |
Modem is in test mode |
|
FAX/TM |
Green |
Off |
Modem is not connected in FAX mode |
|
SUPPORTED STANDARD COMMANDS |
|
Basic AT Commands |
|
+++, comma, A/ |
|
A, B, E, H, L, M, N, O, P, Q, T, V, W, X, Y, Z |
|
&C, &D, &F, &G, &K, &M, &P, &Q, &R, &S, &T, &V, &W, &X, &Y, &Z |
|
Extended AT Commands |
|
\A, \B, \G, \K, \L, \N |
|
%C, %E, %L, %Q |
|
Special AT Commands |
|
+MS |
|
S-Registers |
|
S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S25, S26 |
|
S27, S29, S30, S31, S32, S33, S36, S38, S40, S41, S46, S48, S82, S86, S95 |
Note: See MHI help file for complete information. |
Proprietary AT Command Set
|
DIAL | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] D <#>;[cmds] |
|
Description: |
Dials the telephone number indicated according to any modifiers included in the string. |
|
Command |
Function |
|
DJ |
MNP10 link will be negotiated at highest possible speed for this call. |
|
DL |
Re-dial last number. |
|
DP |
Pulse dialing enabled. |
|
DS=n |
Dial stored telephone number n. |
|
DT |
Tone dialing enabled. |
|
DW |
Dialing resumed following dial tone detection. |
|
D, |
Dialing paused for amount of time specified in S8 register. |
|
D! |
Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. |
|
D@ |
Wait for Quiet Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. |
|
D^ |
Calling tone disabled for this call. |
|
D; |
Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. |
|
DISPLAY INFORMATION | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] In [cmds] |
|
Description: |
Displays information requested about the modem. |
|
Command |
Function |
|
I0 |
Displays product identification code. |
|
I1 |
Displays ROM checksum. |
|
I2 |
Tests and displays ROM checksum result. |
|
I3 |
Displays firmware revision. |
|
I4 |
Displays chipset model. |
|
I5 |
Displays country code. |
|
I6 |
Displays product name. |
|
DISTINCTIVE RING | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &In [cmds] |
|
Description: |
Selects which distinctive ring signals the modem will respond to. |
|
Command |
Function |
|
í &I0 |
Modem will respond to any ring signal. |
|
&I1 |
Modem will only respond to Homefax II type B ring signal. |
|
FLOW CONTROL | |
|
Type: |
Register |
|
Format |
AT [cmds] S39=n [cmds] |
|
Description: |
Selects the type of flow control the modem will use. |
|
Command |
Function |
|
S39=0 |
Flow control disabled. |
|
í S39=3 |
RTS/CTS flow control enabled. |
|
S39=4 |
XON/XOFF flow control enabled. |
|
S39=5 |
Transparent XON/XOFF flow control enabled. |
|
S39=6 |
Both RTS/CTS and XON/XOFF flow control enabled. |
|
LINE SPEED | |
|
Type: |
Register |
|
Format: |
AT [cmds] S37=n [cmds] |
|
Description: |
Sets the maximum allowable data exchange rate attempted during the handshaking process. |
|
Command |
Function |
|
í S37=0 |
Attempt to connect at fastest common speed. |
|
S37=1 |
Set speed to 300bps. |
|
S37=2 |
Set speed to 300bps. |
|
S37=3 |
Set speed to 300bps. |
|
S37=5 |
Set speed to 1200bps. |
|
S37=6 |
Set speed to 2400bps. |
|
S37=7 |
Attempt to connect with V.23. |
|
S37=8 |
Set speed to 4800bps. |
|
S37=9 |
Set speed to 9600bps. |
|
S37=10 |
Set speed to 12Kbps. |
|
S37=11 |
Set speed to 14.4Kbps. |
|
S37=12 |
Set speed to 7200bps. |
|
PROTOCOL/SPEED | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Fn [cmds] |
|
Description: |
Selects the protocol and speed the modem will attempt to connect at. |
|
Command |
Function |
|
F0 |
Auto-detect the highest common connect speed. |
|
F1 |
Select V.21 or Bell 103 at 300bps speed. |
|
F4 |
Select V.22 or Bell 212A at 1200bps speed. |
|
F5 |
Select V.22bis at 2400bps speed. |
|
F6 |
Select V.32 or V.32bis at 4800bps speed. |
|
F7 |
Select V.32bis at 7200bps speed. |
|
F8 |
Select V.32bis or V.32 at 9600bps speed. |
|
F9 |
Select V.32bis at 12Kbps speed. |
|
F10 |
Select V.32bis at 14.4Kbps speed. |