TRENDWARE INTERNATIONAL
TEM-560P PCMCIA
|
Card Type |
Modem, Fax |
|
Chip Set |
Unidentified |
|
Maximum Modem Rate |
33.6Kbps |
|
Maximum Fax Rate |
14.4Kbps |
|
Data Modulation Protocol |
Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.32, V.32bis, V.34, V.34bis, K56flex |
|
Fax Modulation Protocol |
ITU-T V.17, V.21CH2, V.27ter, V.29 |
|
Error Correction/Compression |
MNP5, V.42, V.42bis |
|
Fax Class |
Class I |
|
Data Bus |
PCMCIA |
54928
|
SUPPORTED COMMAND SET |
|
Basic AT Commands |
|
AT, A/ |
|
A, E, H, M, P, Q, T, V, W |
|
&C, &F, &G, &V, &Z |
|
Extended AT Commands |
|
\J, \T, \V |
|
Special Commands |
|
-C |
|
S Registers |
|
S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S30 |
|
Note: See MHI Help File for full command documentation. |
Proprietary AT Command Set
|
COMMUNICATION PROTOCOLS | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Bn [cmds] |
|
Description: |
Selects the communication protocol for data calls |
Note: The B command allows the simultaneous selection of more than one suffix, enabling multiple protocols. | |
|
Command |
Protocol |
|
B0 |
ITU-T V.22 at 1200bps |
|
B1 |
Bell 212A at 1200bps |
|
B2 |
V.23 at 1200/75bps |
|
B3 |
V.23 at 75/1200bps |
|
B15 |
V.21 at 300bps |
|
B16 |
Bell 103 at 300bps |
|
DIAL | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] D<#> [cmds] |
|
Description: |
Dials telephone number according to any modifiers included in the string |
|
Note: |
Any combination of modifiers can be used to produce the desired dial functions in sequence. |
|
Command |
Function |
|
DL |
Re-dial last number |
|
DP |
Pulse dialing enabled |
|
DR |
Answer mode enabled; originate mode disabled following handshake initiation. |
|
DS=n |
Dial stored telephone number n |
|
DT |
Tone dialing enabled/Pulse dialing disabled |
|
DW |
Dialing resumed following dial tone detection |
|
D, |
Dialing paused for amount of time specified in S8 register |
|
D! |
Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. |
|
D@ |
Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. |
|
D; |
Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. |
|
AUTO-MODE DETECTION | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Nn [cmds] |
|
Description: |
Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed. |
|
Command |
Function |
|
N0 |
Auto-mode detection disabled |
|
í N1 |
In originate mode, handshake begins at line speed designated by the S37 register. Modem can shift to a slower speed if necessary. In answer mode, handshake attempted with the following protocols in order - V.FC, V.32bis, V.32, V.22bis, V.22 or Bell 212, V.21, and Bell 103 |
|
ON-LINE | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] On [cmds] |
|
Description: |
Controls on-line command (data transmission) state options. |
Note: The O command must be placed at the end of the command string. | |
|
Command |
Function |
|
O0 |
On-line command mode with no retraining enabled |
|
O1 |
On-line command mode with retraining enabled |
|
O3 |
Issue a rate re-negotiate, then return to on-line state |
|
SELECT CALL PROGRESS RESULT CODES | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Xn [cmds] |
|
Description: |
Enables selection of tone detection and associated result code format options |
|
Command |
Function |
|
X0 |
Busy and dial tone detection disabled; result codes 0 - 4 enabled. |
|
X1 |
Busy and dial tone detection disabled; result codes 0 - 5 & 10 enabled. |
|
X2 |
Busy tone detection disabled, dial tone detection enabled; result codes 0 - 6 & 10 enabled. |
|
X3 |
Busy tone detection enabled, dial tone detection disabled; result codes 0 - 5, 7 & 10 enabled. |
|
í X4 |
Busy and dial tone detection enabled; result codes 0 - 7 & 10 enabled. |
|
X5 |
Busy and dial tone detection enabled; result codes 0 - 7 & 10 enabled. |
|
X6 |
Busy and dial tone detection enabled; result codes 0 - 7 & 10 enabled. |
|
X7 |
Display CONNECT or "1" for all speeds. Check dial tone and busy tone |
|
SOFT RESET | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] Zn [cmds] |
|
Description: |
Restores modem profiles previously saved in non-volatile RAM using the &W command. |
|
Command |
Function |
|
Z0 |
Restore setting 0 |
|
Z1 |
Restore setting 0 |
|
DATA TERMINAL READY (DTR) | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Dn [cmds] |
|
Description: |
Selects modem response to DTR |
Note: The action each variant of &D causes depends on the setting of &Q | |
|
Command |
Function |
|
í &D0 |
Modem does not respond to DTR |
|
&D1 |
Modem goes to command mode after DTR goes is off |
|
&D2 |
Modem goes to command mode and disconnects (hangs up) after DTR goes off; Auto-Answer is disabled. |
|
&D3 |
Modem is initialized after DTR goes off |
|
FLOW CONTROL | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Kn [cmds] |
|
Description: |
Enables flow control options |
|
Command |
Function |
|
&K0 |
Flow control disabled |
|
í &K3 |
RTS/CTS flow control enabled |
|
&K4 |
XON/XOFF flow control enabled |
|
PULSE DIALING RATIO | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Pn [cmds] |
|
Description: |
Selects pulse dial make/break ratio |
|
Command |
Function |
|
í &P0 |
39/61ms at 10pps (North America) |
|
&P1 |
33/67ms at 10pps (Europe) |
|
COMMUNICATIONS MODE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Qn [cmds] |
|
Description: |
Selects communications mode options |
|
Command |
Mode |
|
í &Q0 |
Buffered asynchronous mode, serial port speed follows connect speed. |
|
&Q5 |
Error correction mode |
|
&Q8 |
MNP error control mode |
|
&Q9 |
V.42 or MNP error control mode |
|
DATA SET READY (DSR) | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Sn [cmds] |
|
Description: |
Selects DSR options |
|
Command |
Function |
|
&S0 |
DSR forced high |
|
í &S1 |
DSR high only while modem is handshaking or connected |
|
TEST MODES | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] &Tn |
|
Description: |
Selects test options |
|
Command |
Function |
|
&T0 |
End current test |
|
&T1 |
Begin local analog loopback test |
|
&T3 |
Begin local digital loopback |
|
&T6 |
Request remote digital loopback |
|
STORE ACTIVE PROFILE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Wn [cmds] |
|
Description: |
Writes the values for the active profile into the non-volatile RAM |
Extended AT Commands
|
CONNECT MODE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Nn [cmds] |
|
Description: |
Controls the type of connection the modem will operate in |
|
Command |
Function |
|
\N0 |
Normal mode enabled |
|
\N1 |
Direct mode enabled |
|
\N2 |
Reliable mode enabled |
|
\N3 |
Auto-reliable mode enabled |
|
\N4 |
V.42 reliable mode enabled |
|
FLOW CONTROL TYPE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Qn [cmds] |
|
Description: |
Sets type of flow control used by modem |
|
Command |
Function |
|
\Q0 |
Flow control disabled |
|
\Q1 |
Bidirectional XON/XOFF flow control enabled |
|
\Q3 |
Bidirectional RTS/CTS flow control enabled |
|
BLACKLIST | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] %Bn [cmds] |
|
Description: |
View numbers in blacklist |
|
COMPRESSION | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] %Cn [cmds] |
|
Description: |
Selects data compression |
|
Command |
Function |
|
%C0 |
Data compression disabled |
|
%C1 |
V.42bis/MNP5 enabled |
S(status) -REGISTERS
|
V.34 MODULATION | |
|
Format |
AT [cmds] S28=n [cmds] |
|
Default: |
1 |
|
Range: |
0-255 |
|
Description: |
Controls the V.34 modulation |
|
Command |
Function |
|
S28=0 |
Disabled |
|
S28=1-255 |
Enabled |
|
ERROR CORRECTION NEGOTIATION | |
|
Type: |
Register |
|
Format |
AT [cmds] S36=n [cmds] |
|
Description: |
Selects the action of the modem if it fails to connect with the error-correction protocol set in &Q. |
|
Command |
Function |
|
S36=0, 2 |
Hang up |
|
S36=1, 3 |
Attempt a direct connection |
|
S36=4, 6 |
Attempt a connection at MNP2-4; if that fails, hang up. |
|
S36=5, 7 |
Attempt a connection at MNP2-4; if that fails, attempt a direct connection. |
|
DCE LINE SPEED | |
|
Type: |
Register |
|
Format |
AT [cmds] S37=n [cmds] |
|
Description: |
Sets the maximum allowable data exchange rate attempted during handshake process. |
|
Command |
Function |
|
í S37=0 |
Maximum modem speed |
|
S37=2 |
1200/75bps |
|
S37=3 |
300bps |
|
S37=5 |
1200bps |
|
S37=6 |
2400bps |
|
S37=7 |
4800bps |
|
S37=8 |
7200bps |
|
S37=9 |
9600bps |
|
S37=10 |
12000bps |
|
S37=11 |
14400bps |
|
S37=12 |
16800bps |
|
S37=13 |
19200bps |
|
S37=14 |
21600bps |
|
S37=15 |
24000bps |
|
S37=16 |
26400bps |
|
S37=17 |
28800bps |
|
S37=18 |
31200bps |
|
S37=19 |
33600bps |
|
DIAL LINE RATE | ||
|
Type: |
Register | |
|
Format |
AT [cmds] S38=n [cmds] | |
|
Description: |
56K dial line rate selection | |
|
Command |
Function | |
|
í S38=0 |
56K disabled | |
|
S38=1 |
56K enabled, auto-speed selection, maximum modem speed | |
|
S38=2 |
32000bps | |
|
S38=3 |
34000bps | |
|
S38=4 |
36000bps | |
|
S38=5 |
38000bps | |
|
S38=6 |
40000bps | |
|
S38=7 |
42000bps | |
|
S38=8 |
44000bps | |
|
S38=9 |
46000bps | |
|
S38=10 |
48000bps | |
|
S38=11 |
50000bps | |
|
S38=12 |
52000bps | |
|
S38=13 |
54000bps | |
|
S38=14 |
56000bps | |
|
SLEEP TIMER | |
|
Type: |
Register |
|
Format |
AT [cmds] S89 [cmds] |
|
Range: |
0 - 60 |
|
Unit: |
1 second |
|
Description: |
Sleep mode control timer |
|
Command |
Function |
|
0 |
Disable sleep mode |
|
5 - 60 |
Number of seconds of inactivity before entering sleep mode |
|
TRANSMISSION LEVEL (JAPANESE VERSION ONLY) | |
|
Type |
Register or Configuration |
|
Format |
AT [cmds] S91=n [cmds] |
|
Default |
14 |
|
Range |
6 - 15 |
|
Unit |
-1 dBm |
|
Description |
Sets the signal level for transmission over leased-lines |
|
FEATURE NEGOTIATION OPTIONS | |||
|
Type: |
Register | ||
|
Format: |
AT [cmds] S48=n [cmds] | ||
|
Description: |
Selects active error correction and compression protocols | ||
|
Command |
Function | ||
|
S48=7 |
Detection negotiation and XID negotiation enabled | ||
|
S48=128 |
Fall-back to options set in S36 | ||