PURETEK INDUSTRIAL CO, INC.
28800BPS FAX/MODEM ADAPTER (EXT)
|
Card Type |
Fax, Modem (asynchronous) |
|
Chip Set |
Unidentified |
|
Maximum Data Rate |
28.8Kbps |
|
Maximum Fax Rate |
14.4Kbps |
|
Data Bus |
External |
|
Fax Class |
Class I & II |
|
Data Modulation Protocol |
Bell 103/212A ITU-T V.21, V.22, V.22bis, V.23, V.25, V.32, V.32bis, V.34 Rockwell V.FC |
|
Fax Modulation Protocol |
ITU-T V.17, V.21CH2, V.27ter, V.29 |
|
Error Correction/Compression |
MNP5, V.42, V.42bis |
|
CONNECTIONS | ||||||
|
Function |
Label |
Function |
Label | |||
|
DC power |
CN1 |
Line out |
CN3 | |||
|
RS-232/422 |
CN2 |
Line in |
CN4 | |||
|
USER CONFIGURABLE SETTINGS | ||
|
Setting |
Label |
Position |
|
í DTR normal |
SW1/1 |
Off |
|
Modem ignores DTR |
SW1/1 |
On |
|
í Verbose result codes |
SW1/2 |
Off |
|
Numeric result codes |
SW1/2 |
On |
|
í Result code display enabled |
SW1/3 |
On |
|
Result code display disabled |
SW1/3 |
Off |
|
í Local echo enabled |
SW1/4 |
Off |
|
Local echo disabled |
SW1/4 |
On |
|
í Auto answer disabled |
SW1/5 |
On |
|
Auto answer enabled |
SW1/5 |
Off |
|
í CD signal normal |
SW1/6 |
Off |
|
CD forced high |
SW1/6 |
On |
|
í Load Y or Y1 configuration from NVRAM |
SW1/7 |
Off |
|
Load &F0 generic template configuration from ROM |
SW1/7 |
On |
|
í Smart mode |
SW1/8 |
On |
|
Dumb mode |
SW1/8 |
Off |
|
DIAGNOSTIC LED(S) | |||
|
LED |
Color |
Status |
Condition |
|
AA |
Red |
On |
Auto-answer enabled |
|
AA |
Red |
Off |
Auto-answer disabled |
|
AA |
Red |
Blinking |
Phone is ringing |
|
CD |
Red |
On |
Carrier signal detected |
|
CD |
Red |
Off |
Carrier signal not detected |
|
RD |
Red |
On |
Modem is receiving data |
|
RD |
Red |
Off |
Modem is not receiving data |
|
SD |
Red |
On |
Modem is transmitting data |
|
SD |
Red |
Off |
Modem is not transmitting data |
|
TR |
Red |
On |
DTR signal is high |
|
TR |
Red |
Off |
DTR signal is low |
|
CS |
Red |
On |
CTS forced high and transmit hardware flow control enabled |
|
CS |
Red |
Off |
CTS forced low and transmit hardware flow control disabled |
|
ARQ/FAX |
Red |
On |
Data mode: error correction enabled |
|
ARQ/FAX |
Red |
Off |
Data and Fax mode: error correction and fax disabled |
|
ARQ/FAX |
Red |
Blinking |
Data mode: retransmitting data to remote Fax mode: fax mode enabled |
|
SUPPORTED COMMAND SET |
|
Basic AT Commands |
|
AT, +++, A/ |
|
A, B, E, H, L, M, P, S, T, V |
|
&G, &T |
|
S Registers |
|
S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12 |
|
Note: See MHI Help file for full command documentation. |
Proprietary AT Command Set
For a full command summary, see PURETEK INDUSTRIAL CO, INC.28800BPS FAX/MODEM ADAPTER (INT)