PROMETHEUS PRODUCTS, INC
CYBERPORT PRO PC144IV
|
Card Type |
Fax, Modem (synchronous/asynchronous) |
|
Chip Set |
Unidentified |
|
I/O Options |
Speakerphone |
|
Maximum Data Rate |
14.4Kbps |
|
Maximum Fax Rate |
14.4Kbps |
|
Data Bus |
8-bit ISA |
|
Fax Class |
Class II |
|
Data Modulation Protocol |
Bell 103/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis |
|
Fax Modulation Protocol |
ITU-T V.17, V.21CH2, V.27ter, V.29, V.33 |
|
Error Correction/Compression |
MNP5, V.42, V.42bis |
|
CONNECTIONS | ||||||
|
Function |
Label |
Function |
Label | |||
|
Line out |
CN1 |
Microphone connection |
CN4 | |||
|
Line in |
CN2 |
Sound card connection |
CN5 | |||
|
Speaker connection |
CN3 | |||||
|
SUPPORTED COMMAND SET |
|
Basic AT Commands |
|
AT, +++, Comma, A/ |
|
A, B, C, E, H, L, M, N, O, Q, S, V, W, X, Y, Z |
|
&C, &D, &F, &G, &J, &K, &P, &S, &U, &V, &W, &Y, &Z |
|
Extended AT Commands |
|
\C, \G, \V, \X, %E |
|
S Registers |
|
S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S25, S26, S36 |
|
S37, S38, S46, S48 |
|
Note: Please see MHI Help file for full command documentation. |
Proprietary AT Command Set
|
BREAK TYPE | ||
|
Type: |
Configuration | |
|
Format: |
AT [cmds] \Kn [cmds] | |
|
Description: |
Configures action of break signal | |
|
Command |
Function | |
|
\K0 |
Online command mode enabled, send no break to remote modem | |
|
\K1 |
Break sent to remote modem and buffers cleared | |
|
\K2 |
Online command mode enabled, send no break to remote modem | |
|
\K3 |
Send break to remote modem immediately | |
|
\K4 |
Online command mode enabled, send no break to remote modem | |
|
í \K5 |
Send break with transmitted data | |
|
COMMUNICATIONS MODE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Qn [cmds] |
|
Description: |
Selects communications mode options |
|
Command |
Mode |
|
í &Q0 |
Asynchronous mode, serial port speed follows connect speed. |
|
&Q5 |
Error correction mode, to disable error correction use &Q0, &Q3 or &Q6, or modify S36, S46, or S48 |
|
&Q6 |
Buffered asynchronous mode |
|
COMPRESSION | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] %Cn [cmds] |
|
Description: |
Selects data compression |
|
Command |
Function |
|
%C0 |
MNP5 disabled |
|
%C1 |
MNP5 enabled |
|
CONNECT MODE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Nn [cmds] |
|
Description: |
Controls the type of connection the modem will operate in |
|
Command |
Function |
|
\N0 |
Normal mode enabled |
|
\N1 |
Direct mode enabled |
|
\N2 |
Reliable MNP mode enabled |
|
\N3 |
Auto-reliable mode enabled |
|
\N4 |
LAPM reliable mode enabled |
|
\N5 |
Auto-reliable LAPM and buffer mode enabled |
|
\N6 |
Auto-reliable LAPM and buffer mode plus MNP enabled |
|
DIAL | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] D<#> [cmds] |
|
Description: |
Dials telephone number according to any modifiers included in the string |
|
Note: |
Any combination of modifiers can be used to produce the desired dial functions in sequence. |
|
Modifier |
Function |
|
L |
Re-dial last number |
|
P |
Pulse dialing enabled |
|
S=n |
Dial stored telephone number n=0-3 |
|
T |
Tone dialing enabled |
|
W |
Dialing resumed following dial tone detection for amount of time specified in S7 register |
|
, |
Dialing paused for amount of time specified in S8 register |
|
@ |
Wait for quiet answer for amount of time specified in S7 register |
|
! |
Modem commanded to go off-hook for .5 second before returning on-hook |
|
; |
Modem returned to command state after dialing |
|
DICTIONARY SIZE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] %Dn [cmds] |
|
Description: |
Controls dictionary size |
|
Command |
Function |
|
%D0 |
Select 1/2Kbytes |
|
%D1 |
Select 1Kbytes |
|
%D2 |
Select 2Kbytes |
|
ERROR CONTROL BUFFER SIZE - MAXIMUM | |
|
Type: |
Register |
|
Format: |
AT [cmds] S50=n [cmds] |
|
Default: |
200 |
|
Range: |
0-255 |
|
Unit: |
1 Character |
|
Description: |
Sets the maximum buffer size for error control |
|
ERROR CONTROL BUFFER SIZE - MINIMUM | |
|
Type: |
Register |
|
Format: |
AT [cmds] S49=n [cmds] |
|
Default: |
10 |
|
Range: |
0-255 |
|
Unit: |
1 Character |
|
Description: |
Sets the minimum buffer size for error control |
|
FLOW CONTROL TYPE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Qn [cmds] |
|
Description: |
Sets type of flow control used by modem |
|
Command |
Function |
|
\Q0 |
Flow control disabled |
|
\Q1 |
XON/XOFF; software flow control; RTS/CTS bi-directional enabled |
|
\Q2 |
Unidirectional CTS interface signal enabled |
|
\Q3 |
Bi-directional RTS/CTS flow control enabled |
|
\Q4 |
Unidirectional XON/XOFF flow control by DCE enabled |
|
INACTIVITY TIMER | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Tn [cmds] |
|
Default: |
0 |
|
Range: |
0-90 |
|
Unit: |
1 minute |
|
Description: |
Sets the length of time that the modem does not receive information before it disconnects. |
|
REPORT INFORMATION | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] In [cmds] |
|
Description: |
Displays information requested |
|
Command |
Function |
|
I0 |
Reports 3-digit product code |
|
I1 |
Reports checksum |
|
I2 |
Return OK response |
|
I |
Reports firmware version information |
|
I4 |
Reports configuration settings |