PENRIL DATABILITY NETWORKS
DX V.32TERBO M
|
Modem Type |
Data (synchronous/asynchronous)/Fax |
|
Maximum Data Rate |
19.2Kbps |
|
Maximum Fax Rate |
14.4Kbps |
|
Data Bus |
External |
|
Fax Class |
Class I & II |
|
Data Modulation Protocol |
Bell 103A/212A, 208A/B ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.32terbo |
|
Fax Modulation Protocol |
ITU-T V.17, V.27ter, V.29 |
|
Error Correction/Compression |
MNP5, V.42, V.42bis |
|
CONNECTIONS | |||
|
Purpose |
Location |
Purpose |
Location |
|
Lease line out |
CN1 |
Diagnostic connector |
CN4 |
|
Line in |
CN2 |
AC power |
CN5 |
|
RS-232/422 |
CN3 |
Data/Voice |
BT1 |
|
A/A1 - MI/MIC CONTROL | ||
|
Control Type |
JP3 |
JP4 |
| A/A1 control. |
Pin 1 & 2 closed. |
Pin 1 & 2 closed. |
|
MI/MIC control. |
Pin 2 & 3 closed. |
Pin 2 & 3 closed. |
|
DIAL/LEASE LINE | ||
|
Line Type |
JP1 |
JP2 |
| Dial line connected. |
Pin 1 & 2 closed. |
Pin 1 & 2 closed. |
|
Lease line connected. |
Pin 2 & 3 closed. |
Pin 2 & 3 closed. |
|
DTE CONNECTION - PIN 25 | |
|
Function |
JP6 |
|
Analog loopback (input). |
Pin 1 & 2 closed. |
| Test mode indicator (output). |
Pin 2 & 3 closed. |
|
FACTORY CONFIGURED SETTINGS - DO NOT ALTER | |
|
Jumper |
Setting |
|
JP5 |
Pin 2 & 3 closed. |
|
FRAME/SIGNAL GROUND | |
|
Ground Type |
JP7 |
|
Frame and signal ground connected. |
Pin 1 & 2 closed. |
| Frame and signal ground not connected. |
Pin 2 & 3 closed. |
|
DIAGNOSTIC LED(S) | |||
|
LED |
Color |
Status |
Condition |
|
HS |
Red |
On |
Modem is operating at 7200bps or faster |
|
HS |
Red |
Off |
Modem is operating at slower than 7200bps |
|
AA |
Red |
On |
Auto-answer enabled |
|
AA |
Red |
Off |
Auto-answer disabled |
|
AA |
Red |
Blinking |
Phone is ringing |
|
CD |
Red |
On |
Carrier signal detected |
|
CD |
Red |
Off |
Carrier signal not detected |
|
OH |
Red |
On |
Modem is off-hook |
|
OH |
Red |
Off |
Modem is on-hook |
|
RD |
Red |
On |
Modem is receiving data |
|
RD |
Red |
Off |
Modem is not receiving data |
|
SD |
Red |
On |
Modem is transmitting data |
|
SD |
Red |
Off |
Modem is not transmitting data |
|
TR |
Red |
On |
DTR signal is high |
|
TR |
Red |
Flashing |
Voice mode |
|
MR |
Red |
On |
Modem ready |
|
MR |
Red |
Flashing |
Test mode enabled |
Proprietary AT Command Set
See document V1410 for a full command summary.