IPTools.net.ua

Card Type

Modem/Communication Adapter card

Chip Set

Unidentified

I/O Options:

Analog telephone port (RJ-11), microphone in, audio in, audio out, game/MIDI port, TV/audio in, IDE interface

Maximum Modem Rate

33.6Kbps

Maximum Fax Rate

14.4Kbps

Data Modulation Protocol

ITU-T V.22, V.22bis, V.32, V.32bis, V.34

Fax Modulation Protocol

ITU-T V.17, V.27ter, V.29

Error Correction/Compression

MNP5, V.42, V.42bis

Fax Class

Class I & II

Data Bus

16-bit ISA

CONNECTIONS

Function

Label

Function

Label

Miromedia radio connector

CN1

Microphone in

CN5

Line in (RJ-11)

CN2

Audio in

CN6

Internal telephone connector

CN3/pins 1-5

Audio out

CN7

Microphone connector

CN3/pins 6-8

MIDI/game port

CN8

TV/audio in

CN4

SUPPORTED COMMAND SET

Basic AT Commands

AT, �+++�, A/

A, B, E, F, M, P, Q, T, V, X, Y

&E, &V, &W, &Z

Extended AT Commands

\B \L, \V

%E

Special Commands

"H, "N

+MS

S Registers

S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S25, S30, S32, S33

Note: See MHI Help File for full command documentation.

COMMUNICATIONS MODE

Type:

Configuration

Format:

AT [cmds] &Mn [cmds]

Description:

Selects communications mode

Command

Mode

&M0

Asynchronous mode

COMMUNICATIONS MODE

Type:

Configuration

Format:

AT [cmds] &Qn [cmds]

Description:

Selects communications mode options

Command

Mode

&Q0

Asynchronous mode, serial port speed follows connect speed.

DATA SET READY (DSR)

Type:

Configuration

Format:

AT [cmds] &Sn [cmds]

Description:

Selects DSR options

Command

Function

&S0

DSR forced high

&S1

DSR high only while modem is handshaking or connected

DATA TERMINAL READY (DTR)

Type:

Configuration

Format:

AT [cmds] &Dn [cmds]

Description:

Selects modem response to DTR

Command

Function

&D0

DTR override

&D1

DTR toggle causes online command mode

&D2

DTR toggle causes modem to go on-hook

&D3

Loads profile as specified in &Y

DIAL

Type:

Immediate

Format:

AT [cmds] D<#> [cmds]

Description:

Dials telephone number according to any modifiers included in the string

Note:

Any combination of modifiers can be used to produce the desired dial functions in sequence.

Command

Function

DP

Pulse dialing enabled

DR

Answer mode enabled; originate mode disabled following handshake initiation.

DS=n

Dial stored telephone number n

DT

Tone dialing enabled/Pulse dialing disabled

DW

Dialing resumed following dial tone detection

D,

Dialing paused for amount of time specified in S8 register

D!

Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook.

D@

Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string.

D;

Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command

FLOW CONTROL

Type:

Configuration

Format:

AT [cmds] &Kn [cmds]

Description:

Enables flow control options

Command

Function

&K0

Flow control disabled

&K1

RTS/CTS flow control enabled

&K3

RTS/CTS flow control enabled

&K4

XON/XOFF flow control enabled

&K5

Transparent XON/XOFF flow control enabled

FORCE SPEED MODE

Type:

Configuration

Format:

AT [cmds] &Nn [cmds]

Description:

Selects force speed option in V.32/V.32bis mode

Command

Mode

&N0

Support maximum allowable rate

&N1

Selects maximum allowable rate as specified by register S28

GUARD TONE

Type:

Configuration

Format:

AT [cmds] &Gn [cmds]

Description:

Commands the modem to transmit a guard tone in V.22/V.22bis

Command

Function

&G0

Guard tone disabled

&G2

1800Hz guard tone enabled

HOOK CONTROL

Type:

Immediate

Format:

AT [cmds] Hn [cmds]

Description:

Selects whether the modem is on-hook or off-hook

Command

Function

H0

Modem commanded to go on-hook (hang-up)

LINE TYPE

Type:

Configuration

Format:

AT [cmds] &Ln [cmds]

Description:

Command nonfunctional

Command

Line Type

&L0

Selects switched-network line mode

ON-LINE

Type:

Immediate

Format:

AT [cmds] On [cmds]

Description:

Controls on-line command (data transmission) state options.

Command

Function

O0

On-line command mode with no retraining enabled

PULSE DIALING RATIO

Type:

Configuration

Format:

AT [cmds] &Pn [cmds]

Description:

Selects pulse dial make/break ratio.

Note:

For compatibility purposes only; command nonfunctional

Command

Function

&P0

Returns OK

&P1

Returns OK

REPORT INFORMATION

Type:

Immediate

Format:

AT [cmds] In [cmds]

Description:

Displays information requested

Command

Function

I0

Reports modem version

I1

Reports OK

I2

Tests and reports ROM checksum

I3

Reports version number of installed modem files

I4

Reports modem capabilities string GENERIC Mwave

RESTORE PROFILE ON POWER-UP

Type:

Configuration

Format:

AT [cmds] &Yn [cmds]

Description:

Restores a selected profile into the active profile on power-up (hard reset)

Command

Function

&Y0

Restore profile 0 on power-up

&Y1

Restore profile 1 on power-up

&Y2

Restore factory defaults on power-up

SOFT RESET

Type:

Immediate

Format:

AT [cmds] Zn [cmds]

Description:

Restores modem profiles previously saved in non-volatile RAM using the &W command.

Command

Function

Z0

Restore setting 0

Z1

Restore setting 1

Z2

Restore factory defaults

SPEAKER VOLUME

Type:

Configuration

Format:

AT [cmds] Ln [cmds]

Description:

Controls speaker volume

Command

Function

L0

Minimum volume setting

L1

Low volume setting

L2

Medium volume setting

L3

Highest volume setting

TRANSMIT CARRIER

Type:

Configuration

Format:

AT [cmds] Cn [cmds]

Description:

Controls the transmit carrier switching

Command

Function

C1

Transmit carrier enabled

TRELLIS CODING

Type:

Configuration

Format:

AT [cmds] &Un [cmds]

Description:

Enables/disables trellis coding

Command

Function

&U0

V.32 trellis coding enabled

&U1

V.32 trellis coding disabled

BREAK TYPE

Type:

Configuration

Format:

AT [cmds] \Kn [cmds]

Description:

Configures action of break signal

Command

Break from DTE

Break received from remote modem

\K0

Online command mode enabled, send no break to remote modem

Buffers cleared, break sent to DTE

\K1

Break sent to remote modem and buffered cleared

Buffers cleared, break sent to DTE

\K2

Online command mode enabled, send no break to remote modem

Break sent immediately to DTE

í \K3

Send break to remote modem immediately

Break sent immediately to DTE

COMPRESSION

Type:

Configuration

Format:

AT [cmds] %Cn [cmds]

Description:

Selects data compression

Command

Function

%C0

Data compression disabled

%C1

MNP5 enabled

INACTIVITY TIMER

Type:

Configuration

Format:

AT [cmds] \Tn [cmds]

Range:

0-90

Unit:

1minute

Description:

Sets the length of time that the modem does not receive information before it disconnects. \T0 disables timer

MAXIMUM BLOCK SIZE FOR TRANSMISSION

Type:

Configuration

Format:

AT [cmds] \An [cmds]

Description:

Sets the maximum transmittable block size

Command

Function

\A0

MNP block size is 64 characters

\A1

MNP block size is 128 characters

\A2

MNP block size is 192 characters

\A3

MNP block size is 256 characters

\A4

Variable block size

DSVD MODE

Type:

Configuration

Format:

AT [cmds] -SSE=n [cmds]

Description:

Select whether the modem will use DSVD mode.

Command

Function

í -SSE=0

DSVD mode disabled.

-SSE=1

DSVD mode enabled.

UNIDENTIFIED

Type:

Configuration

Format:

AT [cmds] %TT6r, s, c, p [cmds]

Description:

Unidentified

Command

Function

r=0

2400 (if s=0)

r=1

4800bps

r=2

7200bps

r=3

9600bps

r=4

1200bps

r=5

14.4Kbps

r=6

16.8Kbps

r=7

19.2Kbps

r=8

21.6Kbps

r=9

24.0Kbps (if s¹ 0)

r=A

26.4Kbps (if s¹ 0)

r=B

28.8Kbps (if s¹ 0)

s=7

2400 symbols per second

s=8

3000 symbols per second

s=9

3200 symbols per second

c=0

V.34 low carrier

c>0

V.34 high carrier

V.42bis - MAXIMUM STRING LENGTH

Type:

Immediate

Format:

AT [cmds] "On [cmds]

Range:

6-250

Unit:

Characters

Description:

Selects string size for V.42bis compression

BIT-MAPPED REGISTER S49

Format

AT [cmds] S49=n [cmds]

Range:

0-255

Unit:

Bit-mapped

Description:

Selects call indicator, V.8, and V.34 protocol. Bits are additive

Bit

Value

Function

0

0

Not used

1

1

Call indicator disabled

2

1

V.8 protocol disabled

3

1

V.34 protocol disabled

BIT-MAPPED REGISTER S50

Format

AT [cmds] S50=n [cmds]

Range:

0-255

Unit:

Bit-mapped

Description:

Selects baud rates that the V.34 modem will request for reception

Bit

Value

Function

0

1

2400 baud receive symbol rate disabled

1

1

2743 baud receive symbol rate disabled

2

1

2800 baud receive symbol rate disabled

3

1

3000 baud receive symbol rate disabled

4

1

3200 baud receive symbol rate disabled

5

1

3429 baud receive symbol rate disabled

6

1

Asymmetric symbol rates disabled

7

0

Not used

BIT-MAPPED REGISTER S52

Format

AT [cmds] S52=n [cmds]

Range:

0-255

Unit:

Bit-mapped

Description:

Controls the various features of the V.34 data pump

Bit

Value

Function

0

1

Asymmetric data rates disabled

1

1

Auxiliary channel disabled

2-7

0

Not used

BIT-MAPPED REGISTER S53

Format

AT [cmds] S53=n [cmds]

Range:

0-255

Unit:

Bit-mapped

Description:

Controls request options for: pre-emphasis, constellation warping, constellation shaping, and precoding

Bit

Value

Function

0

0

Not used

1

1

Pre-emphasis requests enabled

2

1

Constellation warping requests enabled

3

1

Constellation shaping requests enabled

4

1

Precoding requests enabled

5-7

0

Not used

CALLING TONE

Type:

Register

Format

AT [cmds] S24=n [cmds]

Description:

Enables/disables calling tone

Command

Function

S24=0

Calling tone disabled.

S24=1

Calling tone enabled.

DCE LINE SPEED

Type:

Register

Format

AT [cmds] S28=n [cmds]

Description:

Sets the maximum allowable data exchange rate attempted during handshake process.

Command

Function

S28=0

Speed of last connection

S28=1

50bps

S28=2

75bps

S28=3

110bps

S28=4

134.5bps

S28=5

150bps

S28=6

300bps

S28=8

1200bps

S28=9

2400bps

S28=10

4800bps

S28=11

7200bps

S28=12

9600bps

S28=13

12.0Kbps

S28=14

14.4Kbps