MOTOROLA
VOICESURFR 28800 INTERNAL
|
Card Type |
Modem (asynchronous) |
|
Chip Set |
Unidentified |
|
I/O Options |
Speaker out, microphone |
|
Maximum Modem Rate |
28.8Kbps |
|
Maximum Fax Rate |
14.4Kbps |
|
Data Modulation Protocol |
Unidentified |
|
Fax Modulation Protocol |
Unidentified |
|
Error Correction/Compression |
Unidentified |
|
Fax Class |
Unidentified |
|
Data Bus |
16-bit ISA |
|
Card Size |
Half-length, full-height card |
|
CONNECTIONS | ||||||
|
Function |
Label |
Function |
Label | |||
|
Line out (RJ-11) |
CN1 |
Speaker out |
CN3 | |||
|
Line in (RJ-11) |
CN2 |
Microphone |
CN4 | |||
|
USER CONFIGURABLE SETTINGS | ||
|
Function |
Label |
Position |
|
í Factory configured - do not alter |
S6 |
Unidentified |
|
í Factory configured - do not alter |
S7 |
Unidentified |
|
í Factory configured - do not alter |
S8 |
Unidentified |
|
SERIAL PORT ADDRESS | ||
|
Setting |
S1 |
S2 |
|
COM1 (3F8h) |
Open |
Open |
|
COM2 (2F8h) |
Closed |
Open |
|
í COM3 (3E8h) |
Open |
Closed |
|
COM4 (2E8h) |
Closed |
Closed |
|
INTERRUPT | |||
|
Setting |
S3 |
S4 |
S5 |
|
IRQ 3 |
Closed |
Open |
Open |
|
IRQ 4 |
Open |
Closed |
Open |
|
í IRQ 5 |
Open |
Open |
Closed |
|
PLUG AND PLAY | |||||
|
Plug & Play |
JP10 |
JP11 |
JP12 |
JP13 |
JP14 |
|
Enabled |
Closed |
Closed |
Closed |
Open |
Closed |
|
í Disabled |
Open |
Open |
Open |
Closed |
Open |
|
SUPPORTED COMMAND SET |
|
Basic AT Commands |
|
AT, +++, A/ |
|
A, E, H, M, O, S, V, X, Y, Z |
|
&F, &V, &W, &Y, &Z |
|
Extended AT Commands |
|
\K, \Q |
|
%A, %C |
|
S Registers |
|
S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S25, S26, S38 |
|
Note: See MHI Help File for full command documentation. |
Proprietary AT Command Set
|
AUTO FALLFORWARD/FALLBACK | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &An [cmds] |
|
Description: |
Controls the auto fallforward/fallback |
|
Command |
Function |
|
í &A0 |
Disable auto fallforward/fallback |
|
&A1 |
Enable auto fallforward/fallback |
|
CONNECTION SPEED NEGOTIATION | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Hn [cmds] |
|
Description: |
Controls the connection speed negotiation |
|
Command |
Function |
|
í &H0 |
V.34 connect speed negotiation (28.8Kbps-300bps) |
|
&H1 |
V.34 (28.8Kbps- 4800bps) |
|
&H2 |
V.32bis automatic (14.4Kbps -300bps) |
|
&H3 |
V.32bis only (14.4Kbps - 4800bps) |
|
&H4 |
V.32 automatic (9600-300bps) |
|
&H5 |
V.32 only (9600-4800bps) |
|
&H6 |
V.22 only (2400-1200bps) |
|
&H7 |
V.22 only (1200bps) |
|
&H8 |
212 only (1200bps) |
|
&H9 |
103 only (300bps) |
|
&H10 |
V.21 only (300bps) |
|
DATA CARRIER DETECT (DCD) | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Cn [cmds] |
|
Description: |
Selects whether the DCD option is enabled or disabled |
|
Command |
Function |
|
í &C0 |
DCD enabled |
|
&C1 |
DCD enabled after carrier signal detected |
|
&C2 |
Force DCD on and toggle DCD on disconnect |
|
DATA SET READY (DSR) | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Sn [cmds] |
|
Description: |
Selects DSR options |
|
Command |
Function |
|
&S0 |
DSR forced high |
|
í &S1 |
DSR high only while modem is handshaking or connected |
|
&S2 |
DSR high only while modem is connected |
|
&S3 |
DSR is forced high in all modes |
|
DATA TERMINAL READY (DTR) | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Dn [cmds] |
|
Description: |
Selects modem response to DTR |
Note: The action each variant of &D causes depends on the setting of &Q | |
|
Command |
Function |
|
í &D0 |
Modem does not respond to DTR |
|
&D1 |
Modem goes to command mode after DTR goes is off |
|
&D2 |
Modem goes to command mode and disconnects (hangs up) after DTR goes off; Auto-Answer is disabled. |
|
&D3 |
Modem is initialized after DTR goes off |
|
DIAL | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] D<#> [cmds] |
|
Description: |
Dials telephone number according to any modifiers included in the string |
|
Note: |
Any combination of modifiers can be used to produce the desired dial functions in sequence. |
|
Command |
Function |
|
DL |
Re-dial last number |
|
DP |
Pulse dialing enabled |
|
DS=n |
Dial stored telephone number n |
|
DT |
Tone dialing enabled/Pulse dialing disabled |
|
DW |
Dialing resumed following dial tone detection |
|
D, |
Dialing paused for amount of time specified in S8 register |
|
D! |
Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. |
|
D@ |
Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. |
|
D; |
Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. |
|
REPORT INFORMATION | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] In [cmds] |
|
Description: |
Displays information requested |
|
Command |
Function |
|
I0 |
Reports product code |
|
I1 |
Reports 000 |
|
I2 |
Reports OK or ERROR |
|
I3 |
Reports firmware revision number |
|
I4 |
Reports configuration settings |
|
RESULT CODES | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Qn [cmds] |
|
Description: |
Enables modem to send result codes to the DTE |
|
Command |
Function |
|
í Q0 |
Result code sending enabled |
|
Q1 |
Result code sending disabled |
|
Q2 |
Call progress messages on originate only |
|
SPEAKER VOLUME | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Ln [cmds] |
|
Description: |
Controls speaker volume |
|
Command |
Function |
|
L0 |
Low volume setting |
|
L1 |
Low volume setting |
|
í L2 |
Medium volume setting |
|
L3 |
Highest volume setting |
|
TRELLIS CODING | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Un [cmds] |
|
Description: |
Controls the trellis coding |
|
Command |
Function |
|
&U0 |
Enable trellis coding for V.32 mode at 9600bps |
|
í &U1 |
Disable trellis coding for V.32 mode at 9600bps |
Extended AT Commands
|
ANSWER MODE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] %On [cmds] |
|
Description: |
Sets the answer mode |
|
Command |
Function |
|
%O0 |
Answer mode if ringing |
|
%O1 |
Forced to answer mode |
|
%O2 |
Automatic answer in originate mode |
|
AUTO-RELIABLE TIME BUFFER CONFIGURATION | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Cn [cmds] |
|
Description: |
Controls the handling of incoming data during auto-reliable time period |
|
Command |
Function |
|
\C0 |
Timeout and fallback, speed buffer, no data buffer |
|
\C1 |
Timeout and fallback, speed buffer, buffer receive data |
|
\C2 |
Auto reliable, fallback with fallback character, speed buffer, no receive data buffer |
|
\C3 |
Timeout and fallback, ITU-T V.14, buffer receive data |
|
\C4 |
Timeout and fallback with fallback character, ITU-T V.14, no data buffer |
|
BREAK SEND | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Bn [cmds] |
|
Description: |
Sends break to modem |
|
Command |
Function |
|
\B0 |
6 data bits, no parity, 1 stop bit |
|
\B1 |
7N1 character length |
|
\B2 |
7P1 character length |
|
\B3 |
8P1 character length |
|
\B4 |
7P2 character length |
|
\B5 |
8P1 character length |
|
CALLER ID | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] #CC=n [cmds] |
|
Description: |
Controls the Caller ID function |
|
Command |
Function |
|
#CC=0 |
Caller ID disabled |
|
#CC=1 |
Caller ID displays formatted data |
|
#CC=2 |
Caller ID displays raw hexadecimal data |
|
CHARACTER ABORT | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] %Kn [cmds] |
|
Description: |
Controls the character abort |
|
Command |
Function |
|
%K0 |
Enable 2 second delay to character abort |
|
%K1 |
Disable delay to character abort |
|
COMPUTER - TO - MODEM SPEED SELECTION | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Tn [cmds] |
|
Description: |
Controls the computer- to - modem speed |
|
Command |
Function |
|
\T0 |
Autobaud |
|
\T1 |
Set speed to last AT command entry speed |
|
\T2 |
Force 300bps after connecting |
|
\T3 |
Force 1200bps after connecting |
|
\T4 |
Force 2400bps after connecting |
|
\T5 |
Force 4800bps after connecting |
|
\T6 |
Force 7200bps after connecting |
|
\T7 |
Force 9600bps after connecting |
|
\T8 |
Force 12.0bps after connecting |
|
\T9 |
Force 14.4bps after connecting |
|
\T10 |
Force 16.8bps after connecting |
|
\T11 |
Force 19.2bps after connecting |
|
\T12 |
Force 21.6bps after connecting |
|
\T13 |
Force 24.0bps after connecting |
|
\T14 |
Force 26.4bps after connecting |
|
\T15 |
Force 28.8bps after connecting |
|
\T16 |
Force 38.4bps after connecting |
|
\T17 |
Force 57.6bps after connecting |
|
\T18 |
Force 76.8bps after connecting |
|
\T19 |
Force 115.2bps after connecting |
|
\T20 |
Force 128.0bps after connecting |
|
CONNECT MODE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Nn [cmds] |
|
Description: |
Controls the type of connection the modem will operate in |
|
Command |
Function |
|
\N0 |
Normal mode enabled |
|
\N1 |
Direct mode enabled |
|
\N2 |
Reliable mode enabled |
|
\N3 |
Auto-reliable mode enabled |
|
\N4 |
V.42 reliable mode enabled |
|
\N5 |
V.42, MNP reliable mode enabled |
|
\N6 |
Simulated controlled carrier |
|
DTR SIGNAL | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] %Zn [cmds] |
|
Description: |
Sets the DTR signal |
|
Command |
Function |
|
%Z0 |
Ignore DTR toggle |
|
%Z1 |
Dial stored phone number (0-3) on DTR toggle |
|
%Z2 |
Attempt to connect on DTR toggle |
|
EXTENDED RESULT CODES | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Vn [cmds] |
|
Description: |
Selects extended result codes |
|
Command |
Function |
|
\V0 |
Connect and protocol message reports modem - to - modem speed |
|
\V1 |
Connect and protocol message reports computer - to - modem speed |
|
\V2 |
Connect message reports computer - to - modem speed/V.42 error correction |
|
\V3 |
Connect message reports computer - to - modem speed |
|
FLOW CONTROL | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Gn [cmds] |
|
Description: |
Selects modem port flow control |
|
Command |
Function |
|
\G0 |
Flow control disabled |
|
\G1 |
XON/XOFF flow control enabled |
|
\G2 |
XON/XOFF flow control only for transmitting data |
|
\G3 |
XON/XOFF flow control with pass-through enabled |
|
PARITY | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] \P [cmds] |
|
Description: |
Controls parity |
|
Command |
Function |
|
\P0 |
Even Parity |
|
\P1 |
Space |
|
\P2 |
Odd |
|
\P3 |
Mark |
|
\P4 |
Automatic |
|
RETRAIN | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] %Q [cmds] |
|
Description: |
Sets the retrain |
|
Command |
Function |
|
%Q0 |
Disable retrain |
|
%Q1 |
Attempt up to 3 retrains and disconnect if unsuccessful |
|
%Q2 |
Retrain until signal quality is good |
|
RETURN CALL PROGRESS MESSAGE SPEED | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] %R [cmds] |
|
Description: |
Sets the return call progress message speed |
|
Command |
Function |
|
%R0 |
Return call progress message at current computer - to - modem speed |
|
%R1 |
Return call progress message at last computer- to - modem speed |
|
%R2 |
Return call progress message at 300bps |
|
%R3 |
Return call progress message at 1200bps |
|
%R4 |
Return call progress message at 2400bps |
|
%R5 |
Return call progress message at 4800bps |
|
%R6 |
Return call progress message at 7200bps |
|
%R7 |
Return call progress message at 9600bps |
|
%R8 |
Return call progress message at 12.0bps |
|
%R9 |
Return call progress message at 14.4bps |
|
%R10 |
Return call progress message at 16.8bps |
|
%R11 |
Return call progress message at 19.2bps |
|
%R12 |
Return call progress message at 21.6bps |
|
%R13 |
Return call progress message at 24.0bps |
|
%R14 |
Return call progress message at 26.4bps |
|
%R15 |
Return call progress message at 28.8bps |
|
%R16 |
Return call progress message at 38.4bps |
|
%R17 |
Return call progress message at 57.6bps |
|
%R18 |
Return call progress message at 76.8bps |
|
%R19 |
Return call progress message at 115.2bps |
|
%R20 |
Return call progress message at 128.0bps |
S(status) -REGISTERS
|
RETRANSMISSION COUNTER | |
|
Type: |
Register |
|
Format |
AT [cmds] S70=n [cmds] |
|
Default: |
100 |
|
Range: |
0-255 |
|
Description: |
Sets the retransmission counter |