OMNILINK COMMUNICATIONS CORPORATION
NETPACER 241
|
Card Type |
ISDN TA |
|
Chipset |
Unidentified |
|
Error Correction/Compression |
Unidentified |
|
I/O Options |
ISDN line in, ISDN line out, 25-pin serial port, RJ-45 serial port, power, RJ-11 line out (4) |
|
ISDN Transfer Rate |
64Kbps x 2 |
|
ISDN Protocol |
V.120, PPP, X.25 |
|
Switch Type |
5ESS, DMS-100, Siemens |
|
Data Bus |
External |
|
CONNECTIONS | |||
|
Function |
Label |
Function |
Label |
|
RJ-45 ISDN interface |
CN1 |
RJ-11 analog phone interface - line 1 |
CN6 |
|
S/T interface |
CN2 |
RJ-11 analog phone interface - line 2 |
CN7 |
|
Serial port 1 (25-pin connector) |
CN3 |
RJ-11 analog phone interface - line 3 |
CN8 |
|
Serial port 2 (RJ-45 interface) |
CN4 |
RJ-11 analog phone interface - line 4 |
CN9 |
|
Power connector |
CN5 | ||
|
Note: RJ-11 lines 1 & 2 share B-channel 1. RJ-11 lines 3 & 4 are assigned to B-channel 2. | |||
|
SUPPORTED COMMAND SET |
|
Basic AT Commands |
|
AT, +++ |
|
A, E, F, V |
|
Note: See MHI Help File for full command documentation. |
PROPRIETARY AT COMMAND SET
|
HOOK CONTROL | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] H |
|
Description: |
Modem hangs up |
|
ON-LINE | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] O |
|
Description: |
Reestablishes data transfer mode |
|
REPORT INFORMATION | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] I |
|
Description: |
Displays firmware version and data |
|
X.23 COMMANDS | |
|
Type: |
Immediate |
|
Format: |
<CR> <CR> [cmds] |
|
Description: |
Configures serial port for X.28 |
|
DIAGNOSTIC LED(S) | |||
|
LED |
Color |
Status |
Condition |
|
T1 |
Unidentified |
On |
Data is being transmitted to serial port 1 |
|
T1 |
Unidentified |
Off |
Data is not being transmitted to serial port 1 |
|
T2 |
Unidentified |
On |
Data is being transmitted to serial port 2 |
|
T2 |
Unidentified |
Off |
Data is not being transmitted to serial port 2 |
|
R1 |
Unidentified |
On |
Data is being received from serial port 1 |
|
R1 |
Unidentified |
Off |
Data is not being received from serial port 1 |
|
R2 |
Unidentified |
On |
Data is being received from serial port 2 |
|
R2 |
Unidentified |
Off |
Data is not being received from serial port 2 |
|
L1 |
Unidentified |
On |
Analog phone equipment is connected to line 1; off-hook |
|
L1 |
Unidentified |
Off |
Analog phone equipment is not connected to line 1; on-hook |
|
L2 |
Unidentified |
On |
Analog phone equipment is connected to line 2; off-hook |
|
L2 |
Unidentified |
Off |
Analog phone equipment is not connected to line 2; on-hook |
|
L3 |
Unidentified |
On |
Analog phone equipment is connected to line 3; off-hook |
|
L3 |
Unidentified |
Off |
Analog phone equipment is not connected to line 3; on-hook |
|
L4 |
Unidentified |
On |
Analog phone equipment is connected to line 4; off-hook |
|
L4 |
Unidentified |
Off |
Analog phone equipment is not connected to line 4; on-hook |
|
B1 |
Unidentified |
On |
Bearer channel 1 is in use |
|
B1 |
Unidentified |
Off |
Bearer channel 1 is not in use |
|
B2 |
Unidentified |
On |
Bearer channel 2 is in use |
|
B2 |
Unidentified |
Off |
Bearer channel 2 is not in use |
|
DCH |
Unidentified |
On |
Data channel is in use |
|
DCH |
Unidentified |
Off |
Data channel is not in use |
|
CON |
Unidentified |
On |
Custom application is installed |
|
CON |
Unidentified |
Off |
Custom application is not installed |
|
UL |
Unidentified |
On |
ISDN connection with the switch is normal |
|
UL |
Unidentified |
Off |
ISDN not connected with the switch. |
|
UL |
Unidentified |
Blinking |
ISDN connection with the switch has been made, but the TEI is being negotiated |
|
ER |
Unidentified |
On |
Errors have been detected on network |
|
ER |
Unidentified |
Off |
Errors have not been detected on network |
|
CA |
Unidentified |
On |
Custom application is being run |
|
CA |
Unidentified |
Off |
Custom application is not being run |
|
PWR |
Unidentified |
On |
Power is on |
|
PWR |
Unidentified |
Off |
Power is off |