NEWCOM, INC.
56IFX(C), 56IFXV(C)
|
Card Type |
Modem (asynchronous) |
|
Chipset |
Unidentified |
|
I/O Options |
Voice (on 56ifxv(c) only) |
|
Maximum Data Rate |
56Kbps |
|
Maximum Fax Rate |
14.4Kbps |
|
Data Modulation |
Bell 103A, 212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34 US Robotics x2 |
|
Fax Modulation |
ITU-T V.17, V.21CH2, V.27ter, V.29 |
|
Error Correction/Compression |
MNP5, V.42, V.42bis |
|
Fax Class |
Class I |
|
Data Bus |
16-bit ISA |
|
Card Size |
Full height, half length |
|
CONNECTIONS | |||
|
Function |
Label |
Function |
Label |
|
Telephone line out |
CN1 |
Not used |
CN4 |
|
Telephone line in |
CN2 |
Not used |
CN5 |
|
Not used |
CN3 | ||
Note: CN3, CN4, and CN5 may not be present on all models. | |||
|
PLUG-N-PLAY | |||
|
Setting |
JP1/A |
JP1/B |
JP1/C |
|
í Enabled |
Closed |
Closed |
Closed |
|
Disabled |
Open |
Open |
Open |
Note: If Plug-N-Play mode is enabled, all other jumper settings must also be set for Plug-N-Play. | |||
|
INTERRUPT SELECTION | |||||||
|
Setting |
JP1/D |
JP1/E |
JP1/F |
JP1/G |
JP1/H |
JP1/I |
JP1/J |
|
3 |
Open |
Open |
Open |
Open |
Open |
Open |
Closed |
|
4 |
Open |
Open |
Open |
Open |
Open |
Closed |
Open |
|
5 |
Open |
Open |
Open |
Open |
Closed |
Open |
Open |
|
7 |
Open |
Open |
Open |
Closed |
Open |
Open |
Open |
|
10 |
Closed |
Open |
Open |
Open |
Open |
Open |
Open |
|
11 |
Open |
Closed |
Open |
Open |
Open |
Open |
Open |
|
12 |
Open |
Open |
Closed |
Open |
Open |
Open |
Open |
|
í Plug-N-Play |
Closed |
Closed |
Closed |
Closed |
Closed |
Closed |
Closed |
|
SERIAL PORT ADDRESS SELECTION | ||||
|
Setting |
JP1/K |
JP1/L |
JP1/M |
JP1/N |
|
3F8h (COM1:) |
Closed |
Closed |
Open |
Open |
|
2F8h (COM2:) |
Closed |
Open |
Open |
Closed |
|
3E8h (COM3:) |
Open |
Closed |
Closed |
Open |
|
2E8h (COM4:) |
Open |
Open |
Closed |
Closed |
|
í Plug-N-Play |
Open |
Open |
Open |
Open |
|
SUPPORTED STANDARD COMMANDS |
|
Basic AT Commands |
|
+++, comma, A/ |
|
A, C, D, E, F, H, L, M, N, O, P, Q, T, V, X, Y, Z |
|
&C, &D, &F, &G, &J, &K, &P, &S, &T, &V, &W, &Y, &Z |
|
Extended AT Commands |
|
\A, \B, \C, \G, \J, \N, \O, \Q, \T, \U, \X, \Y, \Z |
|
%A, %C, %E, %G, %L, %Q |
|
Special AT Commands |
|
-C, "H, -J, "O |
|
S-Registers |
|
S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S24, S25 |
|
S26, S27, S28, S29, S30, S31, S32, S33, S36, S38, S39, S40, S41, S46, S48, S82, S86, S91, S92 |
|
S95 |
Note: See MHI help file for complete information. |
|
IS-101 COMMANDS |
|
+V Commands |
|
+VCID, +VCSD, +VDR, +VEM, +VGM, +VGR, +VGS, +VGT, +VIP, +VIT, +VLS, +VNH, +VRA, +VRN, +VRX |
|
+VSD, +VSM, +VSP, #VSPS, +VTD, +VTS, +VTX |
|
-S Commands |
|
-SAC, -SCD, -SDA, -SDS, -SER, -SFX, -SIC, -SIP, -SQR, -SSP, -SSQ, -SSR, -SSV |
Note: The functions of the IS-101 commands are unidentified. These commands are supported on 56ifxv(c) only. |
Proprietary AT Command Set
See NEWCOM, INC. 336IFXSP(C) for a full command summary.