NEWCOM, INC.
336IFXSP(C)
|
Card Type |
Modem (asynchronous) |
|
Chipset |
Unidentified |
|
I/O Options |
Audio line out, microphone in, speaker out, voice, speakerphone |
|
Maximum Data Rate |
33.6Kbps |
|
Maximum Fax Rate |
14.4Kbps |
|
Data Modulation |
Bell 103A, 212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34 |
|
Fax Modulation |
ITU-T V.17, V.21CH2, V.27ter, V.29 |
|
Error Correction/Compression |
MNP5, V.42, V.42bis |
|
Fax Class |
Class I |
|
Data Bus |
16-bit ISA |
|
Card Size |
Full height, half length |
|
CONNECTIONS | |||
|
Function |
Label |
Function |
Label |
|
Telephone line out |
CN1 |
Headphone line out |
CN4 |
|
Telephone line in |
CN2 |
Speaker out |
CN5 |
|
Microphone in |
CN3 | ||
|
PLUG-N-PLAY | |||
|
Setting |
JP1/A |
JP1/B |
JP1/C |
|
í Enabled |
Closed |
Closed |
Closed |
|
Disabled |
Open |
Open |
Open |
Note: If Plug-N-Play mode is enabled, all other jumper settings must also be set for Plug-N-Play. | |||
|
INTERRUPT SELECTION | |||||||
|
Setting |
JP1/D |
JP1/E |
JP1/F |
JP1/G |
JP1/H |
JP1/I |
JP1/J |
|
3 |
Open |
Open |
Open |
Open |
Open |
Open |
Closed |
|
4 |
Open |
Open |
Open |
Open |
Open |
Closed |
Open |
|
5 |
Open |
Open |
Open |
Open |
Closed |
Open |
Open |
|
7 |
Open |
Open |
Open |
Closed |
Open |
Open |
Open |
|
10 |
Closed |
Open |
Open |
Open |
Open |
Open |
Open |
|
11 |
Open |
Closed |
Open |
Open |
Open |
Open |
Open |
|
12 |
Open |
Open |
Closed |
Open |
Open |
Open |
Open |
|
í Plug-N-Play |
Closed |
Closed |
Closed |
Closed |
Closed |
Closed |
Closed |
|
SERIAL PORT ADDRESS SELECTION | ||||
|
Setting |
JP1/K |
JP1/L |
JP1/M |
JP1/N |
|
3F8h (COM1:) |
Closed |
Closed |
Open |
Open |
|
2F8h (COM2:) |
Closed |
Open |
Open |
Closed |
|
3E8h (COM3:) |
Open |
Closed |
Closed |
Open |
|
2E8h (COM4:) |
Open |
Open |
Closed |
Closed |
|
í Plug-N-Play |
Open |
Open |
Open |
Open |
|
SUPPORTED STANDARD COMMANDS |
|
Basic AT Commands |
|
+++, comma, A/ |
|
A, C, D, E, F, H, L, M, N, O, P, Q, T, V, X, Y, Z |
|
&C, &D, &F, &G, &J, &K, &P, &S, &T, &W, &Y, &Z |
|
Extended AT Commands |
|
\A, \B, \C, \G, \J, \N, \O, \Q, \T, \U, \X, \Y, \Z |
|
%A, %C, %E, %G |
|
Special AT Commands |
|
-C, "H, -J, "O |
|
S-Registers |
|
S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S25, S27 |
|
S30, S31, S33, S37 |
Note: See MHI help file for complete information. |
|
IS-101 COMMANDS |
|
+V Commands |
|
+VBT, +VCID, +VCSD, +VDR, +VEM, +VGM, +VGR, +VGS, +VGT, +VIP, +VIT, +VLS, +VNH, +VRA, +VRN |
|
+VRX, +VSD, +VSM, +VSP, +VTD, +VTS, +VTX, #VSPS |
|
-S Commands |
|
-SAC, -SCD, -SDA, -SDS, -SER, -SFX, -SIC, -SIP, -SQR, -SSP, -SSQ, -SSR, -SSV |
Note: The functions of the IS-101 commands are unidentified. |
Proprietary AT Command Set
|
BREAK TYPE | |||||
|
Type: |
Configuration | ||||
|
Format: |
AT [cmds] \Kn [cmds] | ||||
|
Description: |
Configures action of break signal. | ||||
|
Command |
Break from DTE Reliable/Normal mode |
Break from DTE Direct mode |
Modem receives \B |
Break from remote modem | |
|
\K0 |
Enter command mode, do not send break to remote modem. |
Send break to remote modem immediately, then enter command mode. |
Buffers cleared and break sent to remote modem. |
Buffers cleared and break sent to DTE. | |
|
\K1 |
Buffers cleared and break sent to remote modem. |
Send break to remote modem immediately. |
Buffers cleared and break sent to remote modem. |
Buffers cleared and break sent to DTE. | |
|
\K2 |
Enter command mode, do not send break to remote modem. |
Send break to remote modem immediately, then enter command mode. |
Send break to remote modem immediately. |
Send break to DTE immediately. | |
|
\K3 |
Send break to remote modem immediately. |
Send break to remote modem immediately. |
Send break to remote modem immediately. |
Send break to DTE immediately. | |
|
\K4 |
Enter command mode, do not send break to remote modem. |
Send break to remote modem immediately, then enter command mode. |
Send break to remote modem with transmitted data. |
Break sent with received data to the DTE. | |
|
\K5 |
Send break with transmitted data. |
Send break to remote modem immediately. |
Send break to remote modem with transmitted data. |
Break sent with received data to the DTE. | |
|
COMMUNICATION PROTOCOLS | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Bn [cmds] |
|
Description: |
Selects the communication protocol for low-speed data calls. |
|
Command |
Protocol |
|
B0 |
Modem will use ITU-T V.22 at 1200bps. |
|
í B1 |
Modem will use Bell 212A at 1200bps. |
|
B2 |
Modem will use ITU-T V.23 at 1200/75bps. |
|
B3 |
Modem will use ITU-T V.23 at 75/1200bps. |
|
DISPLAY INFORMATION | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] In [cmds] |
|
Description: |
Displays information requested about the modem. |
|
Command |
Function |
|
I0 |
Displays product identification code. |
|
I1 |
Displays chip firmware revision. |
|
I2 |
Tests and displays ROM checksum result. |
|
I3 |
Displays modem chipset name. |
|
I5 |
Displays hardware configuration. |
|
I6 |
Displays country code. |
|
I7 |
Displays board firmware revision. |
|
I8 |
Displays chipset feature bitmap. |
|
I10 |
Displays board feature bitmap. |
|
I11 |
Displays board feature bitmap. |
|
I14 |
Displays digital SAFE device information. |
|
I20 |
Displays the revision level of the modem's voice chipset. |
|
I21 |
Displays the revision level of the modem's voice firmware. |
|
I22 |
Displays the voice chipset manufacturers name. |
|
I23 |
Displays the model name of the modem's voice chipset. |
|
DISPLAY PROFILES | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] &Vn [cmds] |
|
Description: |
Displays active and stored configuration profiles. |
|
Command |
Function |
|
í &V0 |
Displays stored profile 0. |
|
&V1 |
Displays stored profile 1. |
|
&V3 |
Displays relay status and I/O information. |
|
EXTENDED RESULT CODES | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Wn [cmds] |
|
Description: |
Selects which result codes the modem will report. |
|
Command |
Function |
|
í W0 |
Enables CONNECT result codes to report DTE speed. |
|
W1 |
Enables CONNECT result codes to report DTE speed. |
|
W2 |
Enables CONNECT result codes to report DCE speed. |
|
W3 |
Enables CONNECT result codes to report DTE speed with error correction and compression information. |
|
W4 |
Enables CONNECT result codes to report DTE speed with modulation protocol, error correction, and compression information. |
|
MODE SELECTION | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] +FCLASS=n |
|
Description: |
Sets what mode the modem will operate in. |
|
Command |
Function |
|
+FCLASS=0 |
Data mode. |
|
+FCLASS=1 |
Class 1 fax mode. |
|
+FCLASS=8 |
Voice mode. |
|
+FCLASS=80 |
IS-101 voice mode. |
|
TRELLIS CODING | ||
|
Type: |
Configuration | |
|
Format: |
AT [cmds] &Un [cmds] | |
|
Description: |
Selects whether the modem will use trellis coding. | |
|
Command |
Function | |
|
í &U0 |
Trellis coding enabled. | |
|
&U1 |
Trellis coding disabled. | |