MOTOROLA, INC.
MODEMSURFR 56K (INTERNAL)
|
Card Type |
Modem (asynchronous) |
|
Chip Set |
Rockwell |
|
Maximum Modem Rate |
56Kbps |
|
Maximum Fax Rate |
14.4Kbps |
|
Data Modulation Protocol |
Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34 Rockwell V.FC, K56+ |
|
Fax Modulation Protocol |
ITU-T V.17, V.21CH2, V.27ter, V.29 |
|
Error Correction/Compression |
MNP5, V.42, V.42bis |
|
Fax Class |
Class I |
|
Data Bus |
16-bit ISA |
|
Card Size |
Three-quarter length, full-height |
|
CONNECTIONS | |||
|
Function |
Label |
Function |
Label |
|
Telephone line |
CN1 |
Telephone line |
CN2 |
|
SUPPORTED STANDARD COMMANDS |
|
Basic AT Commands |
|
+++, comma, A/ |
|
A, B, E, H, L, M, N, O, P, Q, T, V, W, X, Y, Z |
|
&C, &D, &F, &G, &K, &P, &R, &S, &T, &V, &W, &Y, &Z |
|
Extended AT Commands |
|
\A, \B, \K, \N, \V |
|
%C, %E, %L, %Q |
|
Special AT Commands |
|
#CID, +MS |
|
S-Registers |
|
S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S24, S25 |
|
S26, S27, S28, S29, S30, S32, S33, S36, S38, S39, S40, S46, S48, S82, S86, S91, S92, S95 |
Note: See MHI help file for complete information. |
|
UNIDENTIFIED COMMANDS | |
|
Command |
Default |
|
+ES=nnn |
3,0,2 |
|
+ESA=nnnnnnnn |
0,0,0,0,0,0,0,0 |
|
+ITF=nn |
255,64 |
Proprietary AT Command Set
|
BIT-MAPPED REGISTER S31 | |||
|
Format: |
AT [cmds] S31=n [cmds] | ||
|
Default: |
2 | ||
|
Range: |
0 - 43 | ||
|
Description: |
Select automode, extended result code format, and caller ID format. | ||
|
Bit |
Value |
Function | |
|
0 |
í 01 |
Extended result codes controlled by S95. Extended result codes set for single-line format. | |
|
1 |
0 í 1 |
Auto-mode detection disabled In originate mode, handshake begins at line speed designated by the S37 register. Modem can shift to a slower speed if necessary. In answer mode, handshake attempted with the following protocols in order - V.FC, V.32bis, V.32, V.22bis, V.22 or Bell 212, V.21, and Bell 103 | |
|
3, 2 |
í 0001 10 |
Enables CONNECT result codes to report DTE speed Full reporting of CONNECT result codes Enables CONNECT result codes to report DCE speed | |
|
5, 4 |
í 0001 10 |
Caller ID disabled. Caller ID displays formatted data. Caller ID displays raw hexadecimal data. | |
|
BIT-MAPPED REGISTER S41 | ||
|
Format |
AT [cmds] S41=n [cmds] | |
|
Default: |
71 | |
|
Range: |
0 - 71 | |
|
Description: |
Selects compression and auto-retrain. | |
|
Bit |
Value |
Function |
|
1, 0 |
00 01 10 í 11 |
Data compression disabled. MNP5 enabled. V.42bis enabled. MNP5 and V.42bis enabled. |
|
6, 2 |
00 01 í 11 |
Auto-retrain disabled. Auto-retrain enabled. Auto-fallback/fall-forward enabled. |
|
5 - 3 |
000 |
Not used. |
|
DIAL | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] D <#>;[cmds] |
|
Description: |
Dials the telephone number indicated according to any modifiers included in the string. |
|
Command |
Function |
|
DL |
Re-dial last number. |
|
DP |
Pulse dialing enabled. |
|
DS=n |
Dial stored telephone number n. |
|
DT |
Tone dialing enabled. |
|
DW |
Dialing resumed following dial tone detection. |
|
D, |
Dialing paused for amount of time specified in S8 register. |
|
D> |
Transmit grounding pulse. |
|
D! |
Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. |
|
D@ |
Wait for Quiet Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. |
|
D& |
Wait for prompt tone detection function enabled. Waits for prompt tone for amount of time specified by the S7 command. |
|
D* |
Toggles calling tone on or off for this call. |
|
D; |
Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. |
|
DISPLAY BLACKLIST NUMBERS | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] *B [cmds] |
|
Description: |
Displays the list of all the numbers on the blacklist and their statuses. |
|
DISPLAY DELAYED NUMBERS | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] *D [cmds] |
|
Description: |
Displays the list of all delayed numbers and their statuses. |
|
DISPLAY INFORMATION | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] In [cmds] |
|
Description: |
Displays information requested about the modem. |
|
Command |
Function |
|
I0 |
Displays product identification code. |
|
I1 |
Displays ROM checksum. |
|
I2 |
Tests and displays ROM checksum result. |
|
I3 |
Displays firmware revision, model, and interface. |
|
I4 |
Displays product name. |
|
I5 |
Displays country code. |
|
I6 |
Displays data pump model and revision. |
|
DISTINCTIVE RING | |||
|
Format: |
AT [cmds] -SDR=n [cmds] | ||
|
Default: |
Unidentified | ||
|
Range: |
0 - 7 | ||
|
Description: |
Selects which distinctive ring signals the modem will respond to. | ||
|
Bit |
Value |
Function | |
|
0 |
0 1 |
Do not respond to distinctive ring type 1. Respond to distinctive ring type 1. | |
|
1 |
0 1 |
Do not respond to distinctive ring type 2. Respond to distinctive ring type 2. | |
|
2 |
0 1 |
Do not respond to distinctive ring type 3. Respond to distinctive ring type 3. | |
|
RPI CONFIGURATION | ||
|
Type: |
Configuration | |
|
Format: |
AT [cmds] +Hn [cmds] | |
|
Description: |
Configures the Rockwell Protocol Interface. | |
|
Command |
Function | |
|
+H0 |
RPI disabled. | |
|
+H1 |
RPI enabled and local serial port speed set to 19.2Kbps. | |
|
+H2 |
RPI enabled and local serial port speed set to 38.4Kbps. | |
|
+H3 |
RPI enabled and local serial port speed set to 57.6Kbps. | |
|
+H11 |
RPI+ enabled. | |