IPTools.net.ua

Card Type

Modem (asynchronous)

Chipset

Unidentified

Maximum Data Rate

14.4Kbps

Maximum Fax Rate

14.4Kbps

Data Modulation

ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis

Fax Modulation

ITU-T V.17, V.27ter, V.29

Error Correction/Compression

MNP5, MNP10EC, V.42, V.42bis

Fax Class

Class I & II

Data Bus

Serial

DIAGNOSTIC LED(S)

LED

Color

Status

Condition

TM

Red

On

Modem is in test mode

TM

Red

Off

Modem is not in test mode

TD

Red

Blinking

Modem is transmitting data

TD

Red

Off

Modem is not transmitting data

RD

Red

Blinking

Modem is receiving data

RD

Red

Off

Modem is not receiving data

OH

Red

On

Modem is off-hook

OH

Red

Off

Modem is on-hook

CD

Red

On

Carrier signal detected

CD

Red

Off

Carrier signal not detected

AA

Red

On

Auto-answer enabled

AA

Red

Off

Auto-answer disabled

AA

Red

Blinking

Phone is ringing

TR

Red

On

DTR signal is high

TR

Red

Off

DTR signal is low

CP

Red

On

Compression enabled

CP

Red

Off

Compression disabled

EC

Red

On

Error correction enabled

EC

Red

Off

Error correction disabled

POWER

Red

On

Power is on

POWER

Red

Off

Power is off

MISCELLANEOUS TECHNICAL NOTES

SUPPORTED STANDARD COMMANDS

Basic AT Commands

+++, �comma�, A/

A, B, E, H, L, M, N, O, P, Q, T, V, W, X, Y, Z

&C, &D, &F, &G, &K, &Q, &R, &S, &V, &W, &Y, &Z

Extended AT Commands

\A, \B, \G, \L, \N, \V

%C, %E, %L, %Q

Special AT Commands

:E, -K

S-Registers

S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S18, S24, S25, S29, S30, S32, S33, S38

S48, S82, S86, S95

UNIDENTIFIED COMMANDS

Command

Default

\K

Unidentified

*S

Unidentified

MNP10EC MODE

Type:

Configuration

Format:

AT [cmds] -SEC=n [cmds]

Description:

Selects whether the modem will attempt to use MNP10EC mode during the handshaking sequence.

Command

Function

-SEC=0

MNP10EC handshaking disabled unless a V.34 connection is attempted via a cellular line.

í -SEC=1

MNP10EC handshaking enabled.

PROTOCOL/SPEED

Type:

Configuration

Format:

AT [cmds] Fn [cmds]

Description:

Selects the protocol and speed the modem will attempt to connect at.

Command

Function

F0

Auto-detect the highest common connect speed.

F1

Select V.21 or Bell 103 at 300bps speed.

F3

Select V.23 at 75/1200bps speed.

F4

Select V.22 or Bell 212A at 1200bps speed.

F5

Select V.22bis at 2400bps speed.

F6

Select V.32 or V.32bis at 4800bps speed.

F7

Select V.32bis at 7200bps speed.

F8

Select V.32bis or V.32 at 9600bps speed.

F9

Select V.32bis at 12Kbps speed.

F10

Select V.32bis at 14.4Kbps speed.