OLICOM, INC.
OC-7111
|
Card Type |
Fax, Modem (asynchronous) |
|
Chip Set |
Unidentified |
|
Maximum Data Rate |
28.8Kbps |
|
Maximum Fax Rate |
14.4Kbps |
|
Data Bus |
PCMCIA Type II |
|
Fax Class |
Class I & II |
|
Data Modulation Protocol |
Bell 103/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34 Rockwell V.FC |
|
Fax Modulation Protocol |
ITU-T V.17, V.21CH2, V.27ter, V.29 |
|
Error Correction/Compression |
MNP5, MNP10, V.42, V.42bis |
V1942
|
MISCELLANEOUS TECHNICAL NOTES |
Note: Due to country specific parameters, S-register settings are unidentified. |
Proprietary AT Command Set
|
AUTOSYNC™ | ||
|
Format |
AT [cmds] S19=n [cmds] | |
|
Default: |
Unidentified | |
|
Range: |
0-30 | |
|
Unit: |
Bit-mapped | |
|
Description: |
Sets options for Hayes AutoSync™ functions. | |
|
Bit |
Value |
Function |
|
0 |
0 |
Not used. |
|
1 |
0 1 |
BSC enabled. HDLC enabled. |
|
2 |
0 1 |
HDLC address detection disabled. HDLC address detection enabled. |
|
3 |
0 1 |
NRZI bit encoding enabled. NRZ2 bit encoding enabled. |
|
4 |
0 1 |
Mark idle enabled. Flag or sync idle enabled. |
|
AUTOSYNC HDLC ADDRESS | |
|
Type: |
Register |
|
Format: |
AT [cmds] S20=n [cmds] |
|
Default: |
Unidentified |
|
Range: |
0-255 |
|
Unit: |
Unidentified |
|
Description: |
Sets the HDLC address/BSC character |
|
AUTO-RETRAIN - AUTO-FALLBACK/FALL-FORWARD | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] %En [cmds] |
|
Description: |
Controls auto-retrain mode and fallback/fall-forward |
|
Command |
Function |
|
í %E0 |
Auto-retrain disabled |
|
%E1 |
Auto-retrain enabled |
|
%E2 |
Auto-fallback/fall-forward enabled |
|
%E3 |
Auto-retrain enabled with fast hang-up |
|
BIT MAPPED REGISTERS | |
|
Register |
Default |
|
S14 |
Unidentified |
|
S21 |
Unidentified |
|
S22 |
Unidentified |
|
S23 |
Unidentified |
|
S27 |
Unidentified |
|
S28 |
Unidentified |
|
S31 |
Unidentified |
|
S40 |
Unidentified |
|
S41 |
Unidentified |
|
S201 |
Unidentified |
|
BREAK SEND | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Bn [cmds] |
|
Default: |
3 |
|
Range: |
1-9 |
|
Unit: |
.1 second |
|
Description: |
Sends break to modem |
|
BREAK TYPE | ||||
|
Type: |
Configuration | |||
|
Format: |
AT [cmds] \Kn [cmds] | |||
|
Description: |
Configures action of break signal | |||
|
Command |
Break from DTE |
Modem receives \B |
Break received from remote modem | |
|
\K0 |
Online command mode enabled, send no break to remote modem |
Break sent to remote modem and buffered cleared |
Buffers cleared, break sent to DTE | |
|
\K1 |
Break sent to remote modem and buffered cleared |
Break sent to remote modem and buffered cleared |
Buffers cleared, break sent to DTE | |
|
\K2 |
Online command mode enabled, send no break to remote modem |
Send break to remote modem immediately |
Break sent immediately to DTE | |
|
\K3 |
Send break to remote modem immediately |
Send break to remote modem immediately |
Break sent immediately to DTE | |
|
\K4 |
Online command mode enabled, send no break to remote modem |
Send break with transmitted data |
Break sent with received data to the DTE | |
|
í \K5 |
Send break with transmitted data |
Send break with transmitted data |
Break sent with received data to the DTE | |
|
COUNTRY CODE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] *NCnn [cmds] |
|
Description: |
Select a country code from NVRAM (nn=00-08) |
|
DIAL | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] D<#> [cmds] |
|
Description: |
Dials telephone number according to any modifiers included in the string |
|
Note: |
Any combination of modifiers can be used to produce the desired dial functions in sequence. |
|
Command |
Function |
|
DJ |
Link will be negotiated at 1200bps for current call only |
|
DK |
Power level adjustment enabled for current call only |
|
DL |
Re-dial last number |
|
DP |
Pulse dialing enabled |
|
DT |
Tone dialing enabled/Pulse dialing disabled |
|
DR |
Accepted but not used. |
|
DS=n |
Dial stored telephone number n |
|
D! |
Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. |
|
DW |
Dialing resumed following dial tone detection |
|
D@ |
Wait for Quiet Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. |
|
D, |
Dialing paused for amount of time specified in S8 register |
|
D; |
Modem returned to command state after dialing. The semicolon can only be placed at the end of the dial command. |
|
D^ |
Calling tone enabled/disabled for current dialing attempt |
|
DIALING CODE | ||
|
Type: |
Configuration | |
|
Format: |
AT [cmds] *Zn [cmds] | |
|
Description: |
Select the dial code for pulse dialing | |
|
Command |
Function | |
|
í *Z0 |
Use dial code 0 | |
|
*Z1 |
Use dial code 1 | |
|
DELAYED NUMBERS | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] *B [cmds] |
|
Description: |
Displays delayed numbers list |
|
DELAYED NUMBERS | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] *D [cmds] |
|
Description: |
Displays delayed numbers list |
|
COMPRESSION | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] %Cn [cmds] |
|
Description: |
Selects data compression |
|
Command |
Function |
|
%C0 |
Data compression disabled |
|
%C1 |
MNP5 enabled |
|
%C2 |
V.42bis enabled |
|
í %C3 |
MNP5 and V.42bis enabled |
|
CONNECT MODE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Nn [cmds] |
|
Description: |
Controls the type of connection the modem will operate in |
|
Command |
Function |
|
\N0 |
Normal mode enabled |
|
\N1 |
Direct mode enabled |
|
\N2 |
MNP reliable mode enabled |
|
í \N3 |
Auto-reliable mode enabled |
|
\N4 |
V.42 reliable mode enabled |
|
\N5 |
MNP auto-reliable mode enabled |
|
FLASH DIAL MODIFIER TIME | |
|
Type: |
Register |
|
Format |
AT [cmds] S29=n [cmds] |
|
Default: |
0 |
|
Range: |
0-255 |
|
Unit: |
Unidentified |
|
Description: |
Time the modem will go on-hook upon receiving the ! dial modifier in dial string. |
|
FLOW CONTROL | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Gn [cmds] |
|
Description: |
Selects modem port flow control |
|
Command |
Function |
|
í \G0 |
Flow control disabled |
|
\G1 |
Flow control enabled |
|
FLOW CONTROL CHARACTER - XOFF | |
|
Type: |
Register |
|
Format: |
AT [cmds] S33=n [cmds] |
|
Default: |
19 |
|
Range: |
0-255 |
|
Unit: |
ASCII |
|
Description: |
Sets the character used to represent XOFF |
|
FLOW CONTROL CHARACTER - XON | |
|
Type: |
Register |
|
Format: |
AT [cmds] S32=n [cmds] |
|
Default: |
17 |
|
Range: |
0-255 |
|
Unit: |
ASCII |
|
Description: |
Sets the character used to represent XON |
|
LINE SIGNAL LEVEL | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] %L [cmds] |
|
Description: |
Returns a value which indicates the received line signal level |
|
LINE SIGNAL QUALITY | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] %Q [cmds] |
|
Description: |
Returns a value which indicates line signal quality |
|
LOCK SERIAL PORT | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Jn [cmds] |
|
Description: |
Sets operation of serial port speed |
|
Command |
Function |
|
í \J0 |
Serial speed locked |
|
\J1 |
Serial speed follows connect speed |
|
MAXIMUM BLOCK SIZE FOR TRANSMISSION | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \An [cmds] |
|
Description: |
Sets the maximum transmittable block size |
|
Command |
Function |
|
\A0 |
MNP block size is 64 characters |
|
í \A1 |
MNP block size is 128 characters |
|
\A2 |
MNP block size is 192 characters |
|
\A3 |
MNP block size is 256 characters |
|
MODULATION SELECTION DISPLAY | ||
|
Type: |
Immediate | |
|
Format: |
AT [cmds] +MS? [cmds] | |
|
Description: |
Displays modulation, automode, minimum rate and maximum rate settings | |
|
Command |
Function | |
|
+MS=? |
Displays supported mode selection | |
|
MODULATION SELECTION | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] +MS=x,y,z,a [cmds] |
|
Description: |
Sets options for active protocol; the transfer rates specified by z and a must be valid for the protocol selected. |
|
Command |
Function |
|
x=0 |
V.21 |
|
x=1 |
V.22 |
|
x=2 |
V.22bis |
|
x=3 |
V.23 |
|
x=9 |
V.32 |
|
x =10 |
V.32bis |
|
x=11 |
V.34 |
|
x =64 |
Bell 103 |
|
x =69 |
Bell 212A |
|
x =74 |
V.FC |
|
y =0 |
Automode disabled |
|
y =1 |
Auto-detect highest speed enabled |
|
z, a=300 |
Set minimum or maximum transfer rate at 300bps, respectively. |
|
z, a =1200 |
Set minimum or maximum transfer rate at 1200bps, respectively. |
|
z, a =2400 |
Set minimum or maximum transfer rate at 2400bps, respectively. |
|
z, a =4800 |
Set minimum or maximum transfer rate at 4800bps, respectively. |
|
z, a =7200 |
Set minimum or maximum transfer rate at 7200bps, respectively. |
|
z, a =9600 |
Set minimum or maximum transfer rate at 9600bps, respectively. |
|
z, a =12000 |
Set minimum or maximum transfer rate at 12000bps, respectively. |
|
z, a =14400 |
Set minimum or maximum transfer rate at 14400bps, respectively. |
|
z, a =16800 |
Set minimum or maximum transfer rate at 16800bps, respectively. |
|
z, a =19200 |
Set minimum or maximum transfer rate at 19200bps, respectively. |
|
z, a =21600 |
Set minimum or maximum transfer rate at 21600bps, respectively. |
|
z, a =24000 |
Set minimum or maximum transfer rate at 24000bps, respectively. |
|
z, a =26400 |
Set minimum or maximum transfer rate at 26400bps, respectively. |
|
z, a =28800 |
Set minimum or maximum transfer rate at 28800bps, respectively. |
|
MNP - EXTENDED SERVICES | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] -Kn [cmds] |
|
Description: |
Selects MNP extended services |
|
Command |
Function |
|
í -K0 |
MNP extended services disabled |
|
-K1 |
MNP extended services enabled |
|
MNP - STREAM/BLOCK MODE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Ln [cmds] |
|
Description: |
Selects the transfer mode for MNP link |
|
Command |
Function |
|
í \L0 |
Stream mode for MNP enabled |
|
\L1 |
Block mode for MNP enabled |
|
MNP10 - FALLBACK | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] -Qn [cmds] |
|
Description: |
Allows MNP10 to fall back to speeds slower than 4800bps |
|
Command |
Function |
|
-Q0 |
MNP10 at 2400 and 1200bps enabled |
|
-Q1 |
MNP10 at 2400 and 1200bps disabled |
|
MNP10 - LINK NEGOTIATION | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] *Hn [cmds] |
|
Description: |
Sets the speed at which MNP10 link negotiation will occur |
|
Command |
Function |
|
*H0 |
Link will be negotiated at highest possible speed |
|
*H1 |
Link will be negotiated at 1200bps |
|
*H2 |
Link will be negotiated at 4800bps |
|
MNP10 - POWER LEVEL ADJUST | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] )Mn [cmds] |
|
Description: |
Controls automatic transmit power level adjustment during MNP 10 link negotiation |
|
Command |
Function |
|
í )M0 |
Power level adjustment disabled |
|
)M1 |
Power level adjustment enabled |
|
REPORT INFORMATION | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] In [cmds] |
|
Description: |
Displays information requested |
|
Command |
Function |
|
I0 |
Reports product code |
|
I1 |
Reports ROM checksum |
|
I2 |
Calculates and reports ROM checksum |
|
I3 |
Reports firmware level |
|
I5 |
Reports country code |
|
SLEEP TIMER | |
|
Type: |
Register |
|
Format |
AT [cmds] S24=n [cmds] |
|
Default: |
0 |
|
Range: |
Unidentified |
|
Unit: |
Unidentified |
|
Description: |
Maximum duration of DTE and DCE inactivity allowed prior to initiating low-power sleep mode. |
|
STORED NUMBERS | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] \Fn [cmds] |
|
Description: |
Displays phone number directory |
|
TEST MODES | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S16=n [cmds] | |
|
Default: |
Unidentified | |
|
Range: |
0-125 | |
|
Unit: |
Bit-mapped | |
|
Description: |
Controls loopback tests, analog, digital, remote digital, and self tests. | |
|
Bit |
Value |
Function |
|
0 |
0 1 |
Local analog loopback not in progress Local analog loopback in progress |
|
1 |
0 |
Not used |
|
2 |
0 1 |
Local digital loopback not in progress Local digital loopback in progress |
|
3 |
0 1 |
Modem not in remote digital loopback Remote digital loopback in progress |
|
4 |
0 1 |
Remote digital loopback not requested Remote digital loopback requested |
|
5 |
0 1 |
Remote digital loopback w/ self-test not in progress Remote digital loopback w/ self-test in progress |
|
6 |
0 1 |
Local analog loopback w/ self-test not in progress Local analog loopback w/ self-test in progress |
|
TRANSMISSION LEVEL - CELLULAR | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] @Mn [cmds] |
|
Default: |
Unidentified |
|
Range: |
0-31 |
|
Unit: |
-1dBm |
|
Description: |
Sets the signal level for transmission while in cellular mode |
|
TRANSMISSION LEVEL - FAX | |
|
Type: |
Register |
|
Format: |
AT [cmds] S92=n [cmds] |
|
Default: |
Unidentified |
|
Range: |
0-15 |
|
Unit: |
-1 dBm |
|
Description: |
Sets the signal level for transmission while in fax mode |
|
TRANSMISSION LEVEL - PSTN | |
|
Type |
Register |
|
Format |
AT [cmds] S91=n [cmds] |
|
Default |
Unidentified |
|
Range |
0-15 |
|
Unit |
-1 dBm |
|
Description |
Sets the signal level for transmission over switched phone lines |
|
V.32 - COMPROMISE EQUALIZER | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] :En [cmds] |
|
Description: |
Controls V.32 compromise equalizer |
|
Command |
Function |
|
:E0 |
Equalizer disabled |
|
í :E1 |
Equalizer enabled |