MAGICRAM, INC.
FM288B
|
Card Type |
Fax, Modem (synchronous/asynchronous) |
|
Chip Set |
Unidentified |
|
Maximum Data Rate |
28.8Kbps |
|
Maximum Fax Rate |
14.4Kbps |
|
Data Bus |
PCMCIA Type II |
|
Fax Class |
Class I & II |
|
Data Modulation Protocol |
Bell 103/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34 |
|
Fax Modulation Protocol |
ITU-T V.17, V.21CH2, V.27ter, V.29 |
|
Error Correction/Compression |
MNP10, V.42bis |
V1923
Proprietary AT Command Set
|
AUTO-RETRAIN - AUTO-FALLBACK/FALL-FORWARD | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] %En [cmds] |
|
Description: |
Controls auto-retrain mode and fallback/fall-forward |
|
Command |
Function |
|
í %E0 |
Auto-retrain disabled |
|
%E1 |
Auto-retrain enabled |
|
%E2 |
Auto-fallback/fall-forward enabled |
|
BIT-MAPPED REGISTER S14 | ||
|
Format |
AT [cmds] S14=n [cmds] | |
|
Default: |
138 | |
|
Range: |
0-174 | |
|
Unit: |
Bit-mapped | |
|
Description: |
Controls echo, result codes and display, dial mode, and answer/originate mode. | |
|
Bit |
Value |
Function |
|
0 |
í 0 |
Not used |
|
1 |
0 í 1 |
Command echo disabled Command echo enabled |
|
2 |
í 01 |
Result codes enabled Result codes disabled |
|
3 |
0 í 1 |
Display result codes in numeric format Display result codes in verbose format |
|
4 |
í 0 |
Not used |
|
5 |
í 01 |
Tone dial enabled Pulse dial enabled |
|
6 |
í 0 |
Not used |
|
7 |
0 í 1 |
Answer mode enabled Originate mode enabled |
|
BIT-MAPPED REGISTER S21 | ||
|
Format |
AT [cmds] S21=n [cmds] | |
|
Default: |
4 | |
|
Range: |
0-253 | |
|
Unit: |
Bit-mapped | |
|
Description: |
Selects jack type, CTS/DCD/DSR signals, low DTR action, and the long space disconnect function. | |
|
Bit |
Value |
Function |
|
0 |
í 01 |
Selects RJ-11 jack Selects RJ-12 or RJ-13 jack |
|
1 |
í 0 |
Not used |
|
2 |
0 í 1 |
CTS forced high CTS follows RTS |
|
4, 3 |
í 0001 10 11 |
DTR signal ignored Modem goes to command mode on low DTR Modem disconnects on low DTR; Auto-Answer is disabled. Modem is initialized on low DTR |
|
5 |
í 01 |
DCD forced high DCD normal |
|
6 |
í 01 |
DSR forced high DSR normal |
|
7 |
í 01 |
Long space disconnect function disabled Long space disconnect function enabled |
|
BIT-MAPPED REGISTER S22 | ||
|
Format |
AT [cmds] S22=n [cmds] | |
|
Default: |
117 | |
|
Range: |
0-127 | |
|
Unit: |
Bit-mapped | |
|
Description: |
Controls speaker volume and controls, and limits results codes. | |
|
Bit |
Value |
Function |
|
1, 0 |
00 í 0110 11 |
Off volume Low level volume Medium level volume High level volume |
|
3, 2 |
00 í 0110 11 |
Speaker off Speaker off on carrier Speaker always on Speaker on during handshake |
|
6, 5, 4 |
000 100 101 110 í 111 |
Basic result codes only enabled Basic and connection speed result codes enabled Basic and connection speed result codes and dialtone detection enabled All result codes except dialtone detection enabled All result codes enabled |
|
BIT-MAPPED REGISTER S23 | ||
|
Format |
AT [cmds] S23=n [cmds] | |
|
Default: |
55 | |
|
Range: |
0-189 | |
|
Unit: |
Bit-mapped | |
|
Description: |
Grants/denies remote digital loopback, controls DTE rate and parity, and sets guard tone. | |
|
Bit |
Value |
Function |
|
0 |
0 í 1 |
Remote digital loopback denied Remote digital loopback allowed |
|
3, 2, 1 |
000 001 010 í 011100 101 110 |
Sets serial port speed to 0-300bps Sets serial port speed to 600bps Sets serial port speed to 1200bps Sets serial port speed to 2400bps Sets serial port speed to 4800bps Sets serial port speed to 9600bps Sets serial port speed to 19200bps |
|
5,4 |
00 01 10 í 11 |
Parity even Not used Parity odd No Parity |
|
7, 6 |
í 0001 10 |
Guard tone disabled Guard tone disabled Guard tone 1800Hz enabled |
|
BIT-MAPPED REGISTER S27 | ||
|
Format |
AT [cmds] S27=n [cmds] | |
|
Default: |
73 | |
|
Range: |
0-110 | |
|
Unit: |
Bit-mapped | |
|
Description: |
Selects synchronous/asynchronous mode, line type, clock source, and ITU-T/Bell modes. | |
|
Bit |
Value |
Function |
|
3, 1, 0 |
000 001 010 011 100 í 101110 |
Asynchronous mode, serial port speed follows connect speed. Asynchronous command mode and synchronous connect mode. Asynchronous command mode and synchronous connect mode, DTR dialing enabled. Asynchronous command mode on low DTR, synchronous connect mode on high DTR. Hayes AutoSync™ mode - serial port locked at 9600bps. Error correction mode Asynchronous mode with buffering |
|
2 |
í 01 |
Switched line Leased line |
|
5, 4 |
í 0001 10 |
Local modem generates transmit clock source Local DTE generates transmit clock source Remote DCE/DTE generates transmit clock source |
|
6 |
0 í 1 |
ITU/T mode Bell mode |
|
BIT-MAPPED REGISTER S28 | ||
|
Format |
AT [cmds] S28=n [cmds] | |
|
Default: |
0 | |
|
Range: |
0-31 | |
|
Unit: |
Bit-mapped | |
|
Description: |
Controls V.23 split speed, transmit/receive speed, pulse dialing, and link negotiation. | |
|
Bit |
Value |
Function |
|
0 |
í 01 |
V.23 split speed operation disabled V.23 split speed operation enabled |
|
1 |
í 01 |
75bps transmit, 1200bps receive enabled 1200bps transmit, 75bps receive enabled |
|
2 |
í 0 |
Not used |
|
4, 3 |
í 0001 10 11 |
39ms make/61ms break at 10pps 33ms make/67ms break at 10pps 39ms make/61ms break at 20pps 33ms make/67ms break at 20pps |
|
5 |
í 0 |
Not used |
|
6, 7 |
í 0001 10 |
Link will be negotiated at highest possible speed Link will be negotiated at 1200bps Link will be negotiated at 4800bps |
|
BIT-MAPPED REGISTER S31 | ||
|
Format |
AT [cmds] S31=n [cmds] | |
|
Default: |
2 | |
|
Range: |
0-10 | |
|
Unit: |
Bit-mapped | |
|
Description: |
Controls auto-baud function and result codes. | |
|
Bit |
Value |
Function |
|
0 |
í 0 |
Not used |
|
1 |
0 í 1 |
Auto-baud disabled Auto-baud enabled |
|
3, 2 |
í 0001 10 |
DTE speed displayed in result codes Extended result codes enabled; DCE and DTE speed displayed in result codes. DCE speed displayed in result codes |
|
BIT-MAPPED REGISTER S39 | |||||
|
Format: |
AT [cmds] S39=n [cmds] | ||||
|
Default: |
3 | ||||
|
Range: |
0-6 | ||||
|
Description: |
Select flow control | ||||
|
Bit |
Value |
Function | |||
|
2 - 0 |
000 í 011100 101 110 |
Flow control disabled RTS/CTS flow control enabled XON/XOFF flow control enabled Transparent XON flow control enabled Both XON/XOFF and RTS/CTS flow control enabled | |||
|
BIT-MAPPED REGISTER S40 | ||
|
Format |
AT [cmds] S40=n [cmds] | |
|
Default: |
107 | |
|
Range: |
0-239 | |
|
Unit: |
Bit-mapped | |
|
Description: |
Controls power level and break handling; selects MNP extended services, MNP10 fallback, and block size. | |
|
Bit |
Value |
Function |
|
0 |
0 í 1 |
MNP extended services disable MNP extended services enable |
|
1 |
0 í 1 |
MNP10 at 2400 and 1200 disabled MNP10 at 2400 and 1200 enabled |
|
2 |
í 01 |
Power level adjustment enabled Power level adjustment disabled |
|
5 - 3 |
000 001 010 011 100 í 101 |
\K0 \K1 \K2 \K3 \K4 \K5 |
|
7, 6 |
00 í 0110 11 |
MNP block size is 64 characters MNP block size is 128 characters MNP block size is 192 characters MNP block size is 256 characters |
|
BIT-MAPPED REGISTER S41 | ||
|
Format |
AT [cmds] S41=n [cmds] | |
|
Default: |
3 | |
|
Range: |
0-91 | |
|
Unit: |
Bit-mapped | |
|
Description: |
Selects compression, auto-retrain, flow control, and MNP mode. | |
|
Bit |
Value |
Function |
|
1 - 0 |
00 01 10 í 11 |
Data compression disabled MNP5 enabled V.42bis enabled MNP5 and V.42bis enabled |
|
6, 2 |
í 0001 10 |
Auto-retrain disabled Auto-retrain enabled Auto-fallback/fall-forward enabled |
|
3 |
í 01 |
Flow control disabled Flow control enabled |
|
4 |
í 01 |
Stream mode for MNP Block mode for MNP |
|
5 |
í 0 |
Not used |
|
BIT-MAPPED REGISTER S201 | |||||
|
Format: |
AT [cmds] S201=n [cmds] | ||||
|
Default: |
32 | ||||
|
Range: |
0-32 | ||||
|
Unit: |
Bit-mapped | ||||
|
Description: |
Sets initial power level and compromise equalizer | ||||
|
Bit |
Value |
Function | |||
|
4-0 |
í 0000000001 00010 ...to... 01010 01011 ...to... 11111 |
-26 dBm -30 dBm -10 dBm ... -10 dBm -11 dBm ...to... -31 dBm | |||
|
5 |
0 í 1 |
Compromise equalizer disabled Compromise equalizer enabled | |||
|
BREAK SEND | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Bn [cmds] |
|
Default: |
3 |
|
Range: |
1-9 |
|
Unit: |
.1 second |
|
Description: |
Sends break to modem |
|
BREAK TYPE | ||||
|
Type: |
Configuration | |||
|
Format: |
AT [cmds] \Kn [cmds] | |||
|
Description: |
Configures action of break signal | |||
|
Command |
Break from DTE |
Modem receives \B |
Break received from remote modem | |
|
\K0 |
Online command mode enabled, send no break to remote modem |
Break sent to remote modem and buffered cleared |
Buffers cleared, break sent to DTE | |
|
\K1 |
Break sent to remote modem and buffered cleared |
Break sent to remote modem and buffered cleared |
Buffers cleared, break sent to DTE | |
|
\K2 |
Online command mode enabled, send no break to remote modem |
Send break to remote modem immediately |
Break sent immediately to DTE | |
|
\K3 |
Send break to remote modem immediately |
Send break to remote modem immediately |
Break sent immediately to DTE | |
|
\K4 |
Online command mode enabled, send no break to remote modem |
Send break with transmitted data |
Break sent with received data to the DTE | |
|
í \K5 |
Send break with transmitted data |
Send break with transmitted data |
Break sent with received data to the DTE | |
|
COMPRESSION | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] %Cn [cmds] |
|
Description: |
Selects data compression |
|
Command |
Function |
|
%C0 |
Data compression disabled |
|
%C1 |
MNP5 enabled |
|
%C2 |
V.42bis enabled |
|
í %C3 |
MNP5 and V.42bis |
|
CONNECT MODE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Nn [cmds] |
|
Description: |
Controls the type of connection the modem will operate in |
|
Command |
Function |
|
\N0 |
Normal mode enabled |
|
\N1 |
Direct mode enabled |
|
\N2 |
Reliable mode enabled |
|
\N3 |
Auto-reliable mode enabled |
|
\N4 |
V.42 error correcting mode enabled |
|
\N5 |
MNP error correcting mode enabled |
|
FLASH DIAL MODIFIER TIME | |
|
Type: |
Register |
|
Format |
AT [cmds] S29=n [cmds] |
|
Default: |
0 |
|
Range: |
0-255 |
|
Unit: |
10 ms |
|
Description: |
Time the modem will go on-hook upon receiving the ! dial modifier in dial string. |
|
FLOW CONTROL | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Gn [cmds] |
|
Description: |
Selects modem port flow control |
|
Command |
Function |
|
í \G0 |
Flow control disabled |
|
\G1 |
Flow control enabled |
|
FLOW CONTROL CHARACTER - XOFF | |
|
Type: |
Register |
|
Format: |
AT [cmds] S33=n [cmds] |
|
Default: |
19 |
|
Range: |
0-255 |
|
Unit: |
ASCII |
|
Description: |
Sets the character used to represent XOFF |
|
FLOW CONTROL CHARACTER - XON | |
|
Type: |
Register |
|
Format: |
AT [cmds] S32=n [cmds] |
|
Default: |
17 |
|
Range: |
0-255 |
|
Unit: |
ASCII |
|
Description: |
Sets the character used to represent XON |
|
LINE SIGNAL LEVEL | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] %L [cmds] |
|
Description: |
Returns a value which indicates the received line signal level (in -dBm) |
|
LINE SIGNAL QUALITY | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] %Q [cmds] |
|
Description: |
Returns a value which indicates line signal quality |
|
LOCK SERIAL PORT | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Jn [cmds] |
|
Description: |
Sets operation of serial port speed |
|
Command |
Function |
|
í \J0 |
Serial speed locked |
|
\J1 |
Serial speed follows connect speed |
|
MAXIMUM BLOCK SIZE FOR TRANSMISSION | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \An [cmds] |
|
Description: |
Sets the maximum transmittable block size |
|
Command |
Function |
|
\A0 |
MNP block size is 64 characters |
|
í \A1 |
MNP block size is 128 characters |
|
\A2 |
MNP block size is 192 characters |
|
\A3 |
MNP block size is 256 characters |
|
MNP - EXTENDED SERVICES | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] -Kn [cmds] |
|
Description: |
Selects MNP extended services |
|
Command |
Function |
|
-K0 |
MNP extended services disabled |
|
í -K1 |
MNP extended services enabled |
|
MNP - STREAM/BLOCK MODE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Ln [cmds] |
|
Description: |
Selects the transfer mode for MNP link |
|
Command |
Function |
|
í \L0 |
Stream mode for MNP enabled |
|
\L1 |
Block mode for MNP enabled |
|
MNP10 - FALLBACK | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] -Qn [cmds] |
|
Description: |
Allows MNP10 to fall back to speeds slower than 4800bps |
|
Command |
Function |
|
-Q0 |
MNP10 at 2400 and 1200bps disabled |
|
í -Q1 |
MNP10 at 2400 and 1200bps enabled |
|
MNP10 - LINK NEGOTIATION | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] *Hn [cmds] |
|
Description: |
Sets the speed at which MNP10 link negotiation will occur |
|
Command |
Function |
|
í *H0 |
Link will be negotiated at highest possible speed |
|
*H1 |
Link will be negotiated at 1200bps |
|
*H2 |
Link will be negotiated at 4800bps |
|
MNP10 - POWER LEVEL ADJUST | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] )Mn [cmds] |
|
Description: |
Controls automatic transmit power level adjustment during MNP 10 link negotiation |
|
Command |
Function |
|
í )M0 |
Power level adjustment disabled |
|
)M1 |
Power level adjustment enabled |
|
SLEEP TIMER | |
|
Type: |
Register |
|
Format |
AT [cmds] S24=n [cmds] |
|
Default: |
1 |
|
Range: |
0-255 |
|
Unit: |
1 second |
|
Description: |
Maximum duration of DTE and DCE inactivity allowed prior to initiating low-power sleep mode. |
|
TEST MODES | ||
|
Type: |
Register | |
|
Format |
AT [cmds] S16=n [cmds] | |
|
Default: |
0 | |
|
Range: |
0-125 | |
|
Unit: |
Bit-mapped | |
|
Description: |
Controls loopback tests, analog, digital, remote digital, and self tests. | |
|
Bit |
Value |
Function |
|
0 |
í 01 |
Local analog loopback not in progress Local analog loopback in progress |
|
1 |
í 0 |
Not used |
|
2 |
í 01 |
Local digital loopback not in progress Local digital loopback in progress |
|
3 |
í 01 |
Modem not in remote digital loopback Remote digital loopback in progress |
|
4 |
í 01 |
Remote digital loopback not requested Remote digital loopback requested |
|
5 |
í 01 |
Remote digital loopback w/ self-test not in progress Remote digital loopback w/ self-test in progress |
|
6 |
í 01 |
Local analog loopback w/ self-test not in progress Local analog loopback w/ self-test in progress |
|
TEST MODE - PTT | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] %TTn [cmds] |
|
Description: |
Send PTT test signals for a line tests |
|
TRANSMISSION LEVEL - PSTN | |
|
Type |
Register or Configuration |
|
Format |
AT [cmds] S91=n [cmds] |
|
Default |
10 |
|
Range |
0-15 |
|
Unit |
-1 dBm |
|
Description |
Sets the signal level for transmission over switched phone lines |
|
TRANSMISSION LEVEL - FAX | |
|
Type: |
Register |
|
Format: |
AT [cmds] S92=n [cmds] |
|
Default: |
10 |
|
Range: |
0-15 |
|
Unit: |
-1 dBm |
|
Description: |
Sets the signal level for transmission while in fax mode |
|
TRANSMISSION LEVEL - LEASED-LINE | |
|
Type: |
Register |
|
Format: |
AT [cmds] S99=n [cmds] |
|
Default: |
10 |
|
Range: |
0-15 |
|
Unit: |
-1 dBm |
|
Description: |
Sets the signal level for transmission over leased-lines |
Proprietary V.25bis Command Set
|
LOCAL CONFIGURATION | |
|
Type: |
Configuration |
|
Format: |
CNLx [cmds] |
|
Description: |
Enables AT command x |
|
PROGRAM IDENTIFICATION | |
|
Type: |
Immediate |
|
Format: |
PRI |
|
Description: |
Returns VAL message |
|
REQUEST STORED NUMBER | |
|
Type: |
Immediate |
|
Format: |
RLNn <CR> |
|
Range: |
0-19 |
|
Unit: |
Memory location |
|
Description: |
Display dial string stored at memory address n |