GLOBAL VILLAGE COMMUNICATIONS
POWERPORT PLATINUM PRO
|
Card Type |
Modem (asynchronous), Ethernet |
|
Chipset |
Unidentified |
|
Boot ROM |
Not available |
|
Network Transfer Rate |
10Mbps |
|
Topology |
Star |
|
Wire Type |
Unshielded twisted pair |
|
Maximum Data Rate |
28.8Kbps |
|
Maximum Fax Rate |
14.4Kbps |
|
Data Modulation |
Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34 Rockwell V.FC |
|
Fax Modulation |
ITU-T V.17, V.21CH2, V.27ter, V.29 |
|
Error Correction/Compression |
MNP5, MNP10EC, V.42, V.42bis |
|
Fax Class |
Class I |
|
Data Bus |
PCMCIA Type II |
53175
|
SUPPORTED STANDARD COMMANDS |
|
Basic AT Commands |
|
+++, comma, A/ |
|
A, D, E, H, M, N, O, V, W, X, Y, Z |
|
&F, &L, &P, &Q, &V, &W, &Y, &Z |
|
Extended AT Commands |
|
\B, \G, \K, \N, \T, \V, \X |
|
%C |
|
S-Registers |
|
S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S36, S38, S46, S48, S95 |
Note: See MHI help file for complete information. |
Proprietary AT Command Set
|
COMMUNICATION PROTOCOLS | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Bn [cmds] |
|
Description: |
Selects the communication protocol for low-speed data calls. |
|
Command |
Protocol |
|
B0 |
Modem will use ITU-T V.22 at 1200bps or 600bps and V.21 at 300bps. |
|
í B1 |
Modem will use Bell 212A at 1200bps and 103A at 300bps. |
|
B2 |
Modem will use ITU-T V.23 at 1200/75bps. |
|
B3 |
Modem will use ITU-T V.23 at 75/1200bps. |
|
B4 |
Modem will use ITU-T V.23 at 600/75bps. |
|
B5 |
Modem will use ITU-T V.23 at 75/600bps. |
|
DISPLAY INFORMATION | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] In [cmds] |
|
Description: |
Displays information requested about the modem. |
|
Command |
Function |
|
I0 |
Displays manufacturer and model information. |
|
I1 |
Displays ROM checksum. |
|
I2 |
Tests and reports ROM checksum. |
|
I3 |
Displays product identification code and version. |
|
I4 |
Displays modem capabilities. |
|
I5 |
Displays version of DSP chip. |
|
I6 |
Displays DSP checksum. |
|
I7 |
Displays release date of firmware. |
|
I8 |
Displays frequency of the controller clock. |
|
I9 |
Displays sync frequency of the DSP chip. |
|
I10 |
Displays DAA type. |
|
LINE SPEED | |
|
Type: |
Register |
|
Format |
AT [cmds] S37=n [cmds] |
|
Description: |
Sets the maximum allowable data exchange rate attempted during handshake process. |
|
Command |
Function |
|
í S37=0 |
Speed of last connection |
|
S37=3 |
Set speed to 300bps. |
|
S37=4 |
Set speed to 600bps. |
|
S37=5 |
Set speed to 1200bps. |
|
S37=6 |
Set speed to 2400bps. |
|
S37=7 |
Set speed to 4800bps. |
|
S37=8 |
Set speed to 7200bps. |
|
S37=9 |
Set speed to 9600bps. |
|
S37=10 |
Set speed to 12Kbps. |
|
S37=11 |
Set speed to 14.4Kbps. |
|
S37=12 |
Set speed to 16.8Kbps. |
|
S37=13 |
Set speed to 19.2Kbps. |
|
S37=14 |
Set speed to 21.6Kbps. |
|
S37=15 |
Set speed to 24Kbps. |
|
S37=16 |
Set speed to 26.4Kbps. |
|
S37=17 |
Set speed to 28.8Kbps. |
|
MNP10EC MODE | ||
|
Type: |
Configuration | |
|
Format: |
AT [cmds] -SEC=n [cmds] | |
|
Description: |
Selects whether the modem will attempt to use MNP10EC mode during the handshaking sequence. | |
|
Command |
Function | |
|
-SEC=0 |
MNP10EC handshaking disabled unless a V.34 connection is attempted via a cellular line. | |
|
í -SEC=1 |
MNP10EC handshaking enabled. | |
|
RESULT CODES | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Qn [cmds] |
|
Description: |
Enables modem to send result codes to the DTE. |
|
Command |
Function |
|
í Q0 |
Result codes enabled. |
|
Q1 |
Result codes disabled. |
|
Q2 |
Result codes enabled in originate mode only. |
|
TRELLIS CODING | ||
|
Type: |
Configuration | |
|
Format: |
AT [cmds] &Un [cmds] | |
|
Description: |
Selects whether the modem will use trellis coding. | |
|
Command |
Function | |
|
í &U0 |
Trellis coding enabled. | |
|
&U1 |
Trellis coding disabled. | |