E-TECH RESEARCH, INC.
C1414AX PCMCIA
|
Card Type |
Modem(synchronous/asynchronous) |
|
Chip Set |
Unidentified |
|
Maximum Data Rate |
14.4Kbps |
|
Maximum Fax Rate |
14.4Kbps |
|
Data Bus |
PCMCIA |
|
Fax Class |
Class I & II |
|
Data Modulation Protocol |
Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis |
|
Fax Modulation Protocol |
ITU-T V.17, V.21CH2, V.27ter, V.29 |
|
Error Correction/Compression |
MNP5, V.42, V.42bis |
Proprietary AT Command Set
V1795
|
BITS PER CHARACTER | ||
|
Type: |
Configuration | |
|
Format: |
AT [cmds] $Ln [cmds] | |
|
Description: |
Controls bits per character | |
|
Command |
Function | |
|
$L0 |
8 bits per character | |
|
$L1 |
9 bits per character | |
|
í $L2 |
10 bits per character | |
|
$L3 |
11 bits per character | |
|
CARRIER DETECT | ||
|
Type: |
Configuration | |
|
Format: |
AT [cmds] &Cn [cmds] | |
|
Description: |
Controls DCD, Computer Systems Interface and Port Contender | |
|
Command |
Function | |
|
&C0 |
DCD forced high | |
|
í &C1 |
DCD follows remote modem | |
|
&C2 |
Conforms to Computer Systems Interface | |
|
&C3 |
Conforms to Port Contender | |
|
CLEAR DOWN/DISCONNECT | ||
|
Type: |
Configuration | |
|
Format: |
AT [cmds] Yn [cmds] | |
|
Description: |
Controls long space disconnect and V.32 clear down | |
|
Command |
Function | |
|
í Y0 |
Long space disconnect disabled | |
|
Y1 |
Long space disconnect enabled | |
|
Y2 |
V.32 clear down enabled | |
|
Y3 |
V.32 clear down and long space disconnect enabled | |
|
COMPRESSION | ||
|
Type: |
Configuration | |
|
Format: |
AT [cmds] $Cn [cmds] | |
|
Description: |
Controls data compression | |
|
Command |
Function | |
|
$C0 |
Data compression disabled | |
|
í $C1 |
Data compression enabled | |
|
CONNECT/SPEED MESSAGE | ||
|
Type: |
Configuration | |
|
Format: |
AT [cmds] $Xn [cmds] | |
|
Description: |
Controls connect and speed message displayed | |
|
Command |
Function | |
|
$X0 |
Normal connect and DCE speed message enabled | |
|
$X1 |
Normal connect and DTE speed message enabled | |
|
í $X2 |
Extended connect and DCE speed message enabled | |
|
$X3 |
Extended connect and DTE speed message enabled | |
|
DIAL INTERRUPT | ||
|
Type: |
Configuration | |
|
Format: |
AT [cmds] $Kn [cmds] | |
|
Description: |
Controls dial interrupt | |
|
Command |
Function | |
|
$K0 |
Dial interrupt disabled | |
|
í $K1 |
Dial interrupt enabled | |
|
DISPLAY STORED INFORMATION | ||
|
Type: |
Configuration | |
|
Format: |
AT [cmds] &Vn [cmds] | |
|
Description: |
Displays stored phone numbers, configuration profiles and S registers | |
|
Command |
Function | |
|
&V0 |
Display stored phone numbers | |
|
&V1 |
Display current configuration profiles | |
|
&V2 |
Display contents of S registers | |
|
&V3 |
Display stored profiles briefly | |
|
DSR SIGNAL | ||
|
Type: |
Configuration | |
|
Format: |
AT [cmds] &Sn [cmds] | |
|
Description: |
Controls DSR, Computer Systems Interface and Port Contender | |
|
Command |
Function | |
|
í &S0 |
DSR forced high | |
|
&S1 |
DSR follows remote modem | |
|
&S2 |
Conforms to Computer Systems Interface | |
|
&S3 |
Conforms to Port Contender | |
|
FLOW CONTROL | ||
|
Type: |
Configuration | |
|
Format: |
AT [cmds] $Fn [cmds] | |
|
Description: |
Controls XON/XOFF, ENQ/ACK, DTR/DSR AND CTS/RTS flow control | |
|
Command |
Function | |
|
$F0 |
XON/XOFF enabled | |
|
$F1 |
XON/XOFF passthrough enabled | |
|
$F2 |
ENQ/ACK enabled | |
|
$F3 |
DTR/DSR enabled | |
|
í $F4 |
CTS/RTS enabled | |
|
$F5 |
Flow control disabled | |
|
LINE SPEED | ||
|
Type: |
Configuration | |
|
Format: |
AT [cmds] &Ln [cmds] | |
|
Description: |
Controls speed at which modem attempts to connect | |
|
Command |
Function | |
|
í &L0 |
Line speed follows DTE speed | |
|
&L1 |
Connect at V.23 75/1200bps | |
|
&L2 |
Not used | |
|
&L3 |
Connect at 300bps | |
|
&L4 |
Not used | |
|
&L5 |
Connect at 1200bps | |
|
&L6 |
Connect at 2400bps | |
|
&L7 |
Connect at 4800bps | |
|
&L8 |
Connect at 7200bps | |
|
&L9 |
Connect at 9600bps | |
|
PROTOCOL | ||
|
Type: |
Configuration | |
|
Format: |
AT [cmds] $En [cmds] | |
|
Description: |
Controls protocol used | |
|
Command |
Function | |
|
$E0 |
Normal mode | |
|
$E1 |
Auto MNP mode | |
|
$E2 |
MNP mode | |
|
í $E3 |
Auto V.42 mode | |
|
$E4 |
LAPM mode | |
|
RETRAIN LIMIT | ||
|
Type: |
Configuration | |
|
Format: |
AT [cmds] &En [cmds] | |
|
Description: |
Controls number of retrains per minute allowed | |
|
Command |
Function | |
|
í &E0 |
Disconnect If more than four retrain attempts in three minutes | |
|
&E1 |
Disconnect If more than four retrain attempts in four minutes | |
|
&E2 |
Disconnect If more than four retrain attempts in five minutes | |
|
&E3 |
Unlimited retrain allowed | |
|
&E4 |
Retrain disabled | |
|
SPEED CONVERSION | ||
|
Type: |
Configuration | |
|
Format: |
AT [cmds] $Sn [cmds] | |
|
Description: |
Controls speed conversion | |
|
Command |
Function | |
|
í $S0 |
Speed conversion enabled | |
|
$S8 |
Speed conversion disabled | |
|
TRANSMISSION LEVEL | ||
|
Type: |
Configuration | |
|
Format: |
AT [cmds] $Tn [cmds] | |
|
Description: |
Controls transmission level | |
|
Command |
Function | |
|
$T0 - $T2 |
-4dBm | |
|
í -$T3 |
-6dBm | |
|
$T4 |
-8dBm | |
|
$T5 |
-10dBm | |
|
$T6 |
-12dBm | |
|
$T7 |
-14dBm | |
|
$T8 |
-16dBm | |