CREATIX POLYMEDIA
PCMCIA 14.4 FAXMODEM
|
Card Type |
Modem (asynchronous) |
|
Chip Set |
Unidentified |
|
Maximum Data Rate |
14.4Kbps |
|
Maximum Fax Rate |
14.4Kbps |
|
Data Bus |
PCMCIA Type II |
|
Fax Class |
Class I |
|
Data Modulation Protocol |
Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis |
|
Fax Modulation Protocol |
ITU-T V.17, V.21CH2, V.27ter, V.29 |
|
Error Correction/Compression |
MNP5, V.42, V.42bis |
V1892
Proprietary AT Command Set
|
AUTO-RETRAIN - FALLBACK/FALLFORWARD | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] %En [cmds] |
|
Description: |
Controls auto-retrain mode and fallback/fall forward |
|
Command |
Function |
|
%E0 |
Auto-retrain disabled |
|
í %E1 |
Auto-retrain enabled |
|
%E2 |
Fallback/fall forward enabled |
|
%E3 |
Auto-retrain enabled but modem will disconnect if EQM reaches hang-up threshold |
|
BREAK SEND | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Bn [cmds] |
|
Default: |
3 |
|
Range: |
Unidentified |
|
Unit: |
.1 second |
|
Description: |
Sends break to modem |
|
BREAK TYPE | |
|
Type |
Configuration |
|
Format |
AT [cmds] \Kn [cmds] |
|
Default |
5 |
|
Range |
1-5 |
|
Description |
Configures action of break signal |
|
COMPRESSION | |
|
Type: |
Configuration |
|
Format: |
AT %Cn |
|
Description: |
Selects data compression |
|
Command |
Function |
|
%C0 |
Data compression disabled |
|
%C1 |
MNP5 enabled |
|
%C2 |
V.42bis enabled |
|
í %C3 |
MNP5 and V.42bis enabled |
|
COMPROMISE EQUALIZER | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] :En [cmds] |
|
Description: |
Controls V.32 compromise equalizer |
|
Command |
Function |
|
:E0 |
Equalizer disabled |
|
í :E1 |
Equalizer enabled |
|
CONNECT MODE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Nn [cmds] |
|
Description: |
Sets connect mode |
|
Command |
Function |
|
\N0 |
Normal mode enabled |
|
\N1 |
Direct mode enabled |
|
\N2 |
Reliable mode enabled |
|
í \N3 |
Auto-reliable mode enabled |
|
\N4 |
LAPM mode enabled |
|
\N5 |
MNP mode enabled |
|
FLOW CONTROL | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Gn [cmds] |
|
Description: |
Selects modem port flow control |
|
Command |
Function |
|
í \G0 |
Flow control disabled |
|
\G1 |
Flow control enabled |
|
MAXIMUM BLOCK SIZE FOR TRANSMISSION | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \An [cmds] |
|
Description: |
Sets the maximum transmittable block size |
|
Command |
Function |
|
\A0 |
MNP block size is 64 characters |
|
\A1 |
MNP block size is 128 characters |
|
\A2 |
MNP block size is 192 characters |
|
í \A3 |
MNP block size is 256 characters |
|
MNP STREAM/BLOCK MODE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Ln [cmds] |
|
Description: |
Selects the transfer mode for MNP |
|
Command |
Function |
|
í \L0 |
Stream mode for MNP enabled |
|
\L1 |
Block mode for MNP enabled |
|
MNP10 COMPRESSION | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] -Kn [cmds] |
|
Description: |
Selects MNP10 data compression from V.42 LAPM |
|
Command |
Function |
|
-K0 |
MNP10 disabled |
|
í -K1 |
MNP10 enabled |
|
-K2 |
MNP10 enabled on originate mode only |
|
MNP10 FALLBACK | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] -Qn [cmds] |
|
Description: |
Allows MNP10 to fallback to speeds slower than 4800bps |
|
Command |
Function |
|
-Q0 |
MNP10 at 2400 and 1200bps disabled |
|
í -Q1 |
MNP10 at 2400 and 1200bps enabled |
|
MNP10 LINK NEGOTIATION | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] *Hn [cmds] |
|
Description: |
Sets the speed at which MNP10 link negotiation will occur |
|
Command |
Function |
|
í *H0 |
Link will be negotiated at highest possible speed |
|
*H1 |
Link will be negotiated at 1200bps |
|
*H2 |
Link will be negotiated at 4800bps |
|
MNP10 POWER LEVEL ADJUST | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] )Mn [cmds] |
|
Description: |
Controls automatic transmit power level adjustment during MNP 10 link negotiation |
|
Command |
Function |
|
í )M0 |
Power level adjustment disabled |
|
)M1 |
Power level adjustment enabled |
|
REPORT LINE SIGNAL LEVEL | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] %L [cmds] |
|
Description: |
Returns received line signal level |
|
REPORT LINE SIGNAL QUALITY | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] %Q [cmds] |
|
Description: |
Reports line signal quality |
|
TRANSMISSION LEVEL | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] @Mn [cmds] |
|
Default: |
0 |
|
Range: |
11-31 |
|
Unit: |
-1dBm |
|
Description: |
Sets the initial signal level for transmission |
|
Command |
Function |
|
@M0 |
-26dBm |
|
@M1 |
-30dBm |
|
@M2-@M10 |
-10dBm |