ACTION WELL DEVELOPMENT, LTD.
AC-5618 (REV. 1.0)
|
Card Type |
Modem |
|
Chipset |
Unidentified |
|
I/O Options |
Audio in - CD-ROM, speaker connector, line in, line out, audio in, audio out, microphone in |
|
Maximum Modem Rate |
56.0Kbps |
|
Maximum Fax Rate |
14.4Kbps |
|
Fax Class |
Class I |
|
Modem Modulation Protocol |
Bell 103/212A ITU-T V.22bis,V.32, V.32bis, V.34, V.34bis, V.90 |
|
Fax Modulation Protocol |
ITU-T V.17 |
|
Error Correction/Compression |
MNP5, V.42, V.42bis |
|
Data Bus |
16-bit ISA |
|
CONNECTIONS | ||||||
|
Function |
Label |
Function |
Label | |||
|
Line in |
CN1 |
Audio out |
CN5 | |||
|
Line out |
CN2 |
Audio in - CD-ROM |
CN6 | |||
|
Microphone in |
CN3 |
Audio in - CD-ROM |
CN7 | |||
|
Audio in |
CN4 | |||||
|
SUPPORTED COMMAND SET | |
|
Basic AT Commands | |
|
AT, +++, A/ | |
|
A, E, H, M, O, P, Q, T, V | |
|
&C, &P, &V, &W, &Z | |
|
Extended AT Commands | |
|
\A, \B, \N | |
|
%C, %E | |
|
S Registers | |
|
S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12 | |
|
Special Commands | |
|
+MS, #CID | |
|
Voice Commands | |
|
#TL, #VBT, #VRA, #VRX, #VSD, #VSP, #VSS, #VTD, #VTS, #VTX, #SPK | |
|
Note: |
See MHI Help File for full command documentation. Further information on S-registers is currently unavailable |
Proprietary AT Command Set
|
AUTO-MODE DETECTION | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Nn [cmds] |
|
Description: |
Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed. |
|
Command |
Function |
|
N0 |
Auto-mode detection disabled. Handshake begins at line speed designated by the S32 register |
|
í N1 |
Auto-mode detection enabled. Handshake conducted according to the automode algorithm supported by the modem |
|
COMMUNICATION PROTOCOLS | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Bn [cmds] |
|
Description: |
Selects the communication protocol for data calls |
|
Command |
Protocol |
|
B0 |
ITU-T V.22 at 1200bps |
|
COMPRESSION | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Kn [cmds] |
|
Description: |
Selects data compression |
|
Command |
Function |
|
&K0 |
Data compression disabled |
|
&K1 |
MNP5 enabled |
|
&K2 |
V.42bis enabled |
|
&K3 |
MNP5 and V.42bis; or data compression and correction enabled |
|
CONNECT MESSAGE SPEED SOURCE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &En [cmds] |
|
Description: |
Selects source for speed field in CONNECT message |
|
Command |
Function |
|
í &E0 |
DCE speed field |
|
&E1 |
DTE speed field |
|
CONNECT MESSAGES | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &An [cmds] |
|
Description: |
Selects the format of CONNECT messages |
|
Command |
Function |
|
í &A0 |
CONNECT only |
|
&A1 |
Modulation indicator added to CONNECT message |
|
&A2 |
Error detection and data compression indicators added to CONNECT message |
|
&A3 |
Modulation, error detection and data compression indicators added to CONNECT message |
|
DATA SET READY (DSR) | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Sn [cmds] |
|
Description: |
Selects DSR options |
|
Command |
Function |
|
&S0 |
DSR forced high |
|
&S1 |
DSR high only while modem is handshaking or connected |
|
DATA TERMINAL READY (DTR) | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Dn [cmds] |
|
Description: |
Selects modem response to DTR |
|
Command |
Function |
|
í &D0 |
DTR forced high |
|
&D1 |
DTR toggle causes online command mode |
|
&D2 |
Normal DTR operations |
|
&D3 |
Resets on receipt of DTR |
|
DEFAULT CONFIGURATION | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Yn [cmds] |
|
Description: |
Selects the default user defined configuration |
|
Note: |
Does not load configuration |
|
Command |
Function |
|
Y0 |
Select user template 0 |
|
Y1 |
Select user template 1 |
|
í Y2 |
Select factory setting 0 |
|
Y3 |
Select factory setting 1 |
|
DIAL | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] D<#> [cmds] |
|
Description: |
Dials telephone number according to any modifiers included in the string |
|
Note: |
Any combination of modifiers can be used to produce the desired dial functions in sequence. |
|
Command |
Function |
|
DL |
Re-dial last number |
|
DP |
Pulse dialing enabled |
|
DS=n |
Dial stored telephone number n |
|
DT |
Tone dialing enabled/Pulse dialing disabled |
|
DW |
Dialing resumed following dial tone detection |
|
D, |
Dialing paused for amount of time specified in S8 register |
|
D@ |
Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. |
|
D! |
Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. |
|
D; |
Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. |
|
FACTORY DEFAULT PROFILE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Fn [cmds] |
|
Description: |
Sets values in active profile to values found in the default profile |
|
Command |
Function |
|
í &F0 |
Restore factory configuration 0 |
|
&F1 |
Restore factory configuration 1 |
|
FLOW CONTROL | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Hn [cmds] |
|
Description: |
Enables/disables flow control |
|
Command |
Function |
|
&H0 |
Flow control disabled |
|
í &H1 |
RTS to CTS flow control enabled |
|
REPORT INFORMATION | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] In [cmds] |
|
Description: |
Displays information requested |
|
Command |
Function |
|
I1 |
Reports manufacturer and model name |
|
I2 |
Reports software version and provider |
|
I3 |
Reports vendor/chip ID |
|
I4 |
Reports stored and active profile |
|
I5 |
Reports stored and active profile |
|
I6 |
Reports stored and active profile |
|
I7 |
Reports stored telephone numbers |
|
RTS/CTS | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Rn [cmds] |
|
Description: |
Selects RTS/CTS options |
|
Command |
Function |
|
&R0 |
RTS is ignored |
|
&R1 |
Modem recieves data only on RTS |
|
SELECT CALL PROGRESS RESULT CODES | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Xn [cmds] |
|
Description: |
Enables selection of tone detection and associated result code format options |
|
Command |
Function |
|
X0 |
Busy and dial tone detection disabled; result codes 0 - 4 enabled. |
|
X1 |
Busy and dial tone detection disabled; result codes 0 - 5 & 9 - 1212 enabled. |
|
X2 |
Busy tone detection disabled, dial tone detection enabled; result codes 0 - 6 & 9 - 1212 enabled. |
|
X3 |
Busy tone detection enabled, dial tone detection disabled; result codes 0 - 5, 7 - 1212 enabled. |
|
X4 |
Busy and dial tone detection enabled; result codes 0 - 1212 enabled. |
|
SOFT RESET | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] Zn [cmds] |
|
Description: |
Restores modem profiles previously saved in non-volatile RAM |
|
Command |
Function |
|
Z0 |
Restore default user template as defined by Yn |
|
Z1 |
Restore user template 0 |
|
Z2 |
Restore user template 1 |
|
Z3 |
Restore factory setting 0 |
|
Z4 |
Restore factory setting 1 |
|
SPEAKER VOLUME | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Ln [cmds] |
|
Description: |
Controls speaker volume |
|
Command |
Function |
|
L0 |
Low volume setting |
|
L1 |
Low volume setting |
|
í L2 |
Medium volume setting |
|
L3 |
Highest volume setting |
|
TEST MODES | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] &Tn |
|
Description: |
Selects test options |
|
Command |
Function |
|
í &T0 |
TBD |
|
&T1 |
TBD |
|
&T2 |
TBD |
|
&T3 |
TBD |
EXTENDED AT COMMAND SET
|
BREAK TYPE | ||
|
Type: |
Configuration | |
|
Format: |
AT [cmds] \Kn [cmds] | |
|
Description: |
Configures action of break signal | |
|
Command |
Function | |
|
\K0 |
Online command mode enabled, send no break to remote modem | |
|
\K1 |
Break sent to remote modem and buffered cleared | |
|
\K2 |
Online command mode enabled, send no break to remote modem | |
|
\K3 |
Send break to remote modem immediately | |
|
\K4 |
Online command mode enabled, send no break to remote modem | |
|
í \K5 |
Send break with transmitted data | |
VOICE COMMANDS
|
INACTIVITY TIMER | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] #VIT=n [cmds] |
|
Range: |
0-255 |
|
Unit: |
.1ms |
|
Description: |
Maximum duration of voice inactivity allowed prior to initiating hang-up process. |
|
MODE SELECTION | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] #CLS=n [cmds] |
|
Description: |
Selects which mode the modem will operate in. |
|
Command |
Function |
|
#CLS=0 |
Modem will operate in data mode. |
|
#CLS=1 |
Modem will operate in fax class I mode. |
|
#CLS=8 |
Modem will operate in voice mode. |
|
RECORD GAIN | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] #RG=hhhh [cmds] |
|
Range: |
0000 - 7FFF |
|
Unit: |
Unidentified (hexadecimal) |
|
Description: |
Sets the record gain. #RG? queries value |
|
VOICE - LOCAL SERIAL PORT SPEED | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] #BDR=n [cmds] |
|
Range: |
0-48 |
|
Unit: |
2400bps |
|
Description: |
Sets the speed of the local serial port when in voice mode. |
|
VOICE DEVICE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] #VLS=n [cmds] |
|
Description: |
Selects the I/O device for the DSP chip. |
|
Note: |
VLS? Queries current setting. #VLS=? Command will display the available options. |
|
Command |
Function |
|
í #VLS=0 |
Telephone line and handset used for voice I/O. |
|
#VLS=2 |
Internal speaker only used for voice I/O. |
|
#VLS=3 |
External microphone only used for voice I/O. |
|
#VLS=4 |
Telephone line and handset used for voice I/O; internal speaker enabled. |
|
#VLS=6 |
Speakerphone used for voice I/O. |
|
VOICE PARAMETERS | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] #VIP [cmds] |
|
Description: |
Initializes voice parameters |
|
VOICE RING DETECT TIME | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] #VRN=n [cmds] |
|
Default: |
Unidentified |
|
Range: |
0-255 |
|
Unit: |
.1ms |
|
Description: |
Sets the maximum time the modem will wait for the remote station to ring before it assumes that it went off-hook before it rang. |
|
VOICE SAMPLE QUALITY | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] #VBS=n [cmds] |
|
Description: |
Selects the number of bits per sample that the modem records. |
|
Note: |
This modem may not support all options listed below. The #VBS? Command will display the available options. |
|
Command |
Function |
|
#VBS=2 |
Modem records 2 bits per sample in ADPCM encoding. |
|
#VBS=4 |
Modem records 4 bits per sample in ADPCM encoding. |
|
#VBS=8 |
Modem records 8 bits per sample in PCM encoding. |
|
#VBS=16 |
Modem records 16 bits per sample in PCM encoding. |
|
VOICE SAMPLING RATE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] #VSR=n [cmds] |
|
Description: |
Sets the sampling rate used when recording voice signals. #VSR? queries settings |
|
Command |
Function |
|
#VSR=7200 |
Selects a sampling rate of 7.2KHz. |
|
#VSR=8000 |
Selects a sampling rate of 8.0KHz. |
|
VOICE TIMING MARK | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] #VTM=n [cmds] |
|
Range: |
1-10 |
|
Unit: |
1ms |
|
Description: |
Configures timing mark placement. |
|
VOICE VOLUME LEVEL | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] #VGT=n [cmds] |
|
Range: |
0-255 |
|
Description: |
Sets the volume level when playing back audio signals. |