IPTools.net.ua

Card Type

Modem, Fax

Chip Set

Unidentified

I/O Options

microphone, speaker out

Maximum Modem Rate

56Kbps

Maximum Fax Rate

14.4Kbps

Data Modulation Protocol

ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34, V.90, K56 flex

Fax Modulation Protocol

ITU-T V.17, V.21CH2, V.27ter, V.29

Error Correction/Compression

MNP2-4,MNP5, V.42, V.42bis

Fax Class

Class I & II

Data Bus

32-bit PCI

Card Size

Half-length, half-height card

CONNECTIONS

Function

Label

Function

Label

Microphone

CN1

Speaker out

CN2

SUPPORTED COMMAND SET

Basic AT Commands

AT, A/

A, E, H, L, M, O, Q, S, T, V, X, Z

&C, &F, &P, &V

Extended AT Commands

%Q

S Registers

S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12

Special Commands

+MS

Note: See MHI Help File for full command documentation.

DIAL

Type:

Immediate

Format:

AT [cmds] D<#> [cmds]

Description:

Dials telephone number according to any modifiers included in the string

Note:

Any combination of modifiers can be used to produce the desired dial functions in sequence.

Command

Function

DL

Re-dial last number

DP

Pulse dialing enabled

DS=n

Dial stored telephone number n

DT

Tone dialing enabled/Pulse dialing disabled

DW

Dialing resumed following dial tone detection

D,

Dialing paused for amount of time specified in S8 register

D"WXY"

Optional method of denoting telephone numbers. Letters enclosed in quotes are interpreted as numbers according to the system found on a telephone keypad.

D!

Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook.

D&

Wait for credit card bong before continuing with the dial string

D^

Toggles calling tone enable/disable

D@

Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string.

D$

Wait for prompt tone detection function enabled. Waits for prompt tone for amount of time specified by the S7 command.

D;

Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command.

REPORT INFORMATION

Type:

Immediate

Format:

AT [cmds] In [cmds]

Description:

Displays information requested

Command

Function

I0

Reports modem model and speed

I1

Reports ROM checksum

I2

Tests and reports ROM checksum

I3

Unidentified

I4

Unidentified

I5

Unidentified

I6

Reports data connection information

I7

Reports manufacturer and model information

DATA TERMINAL READY (DTR)

Type:

Configuration

Format:

AT [cmds] &Dn [cmds]

Description:

Selects modem response to DTR

Command

Function

í &D0

Modem does not respond to DTR

&D1

Modem goes to command mode after DTR goes is off

&D2

Modem goes to command mode and disconnects (hangs up) after DTR goes off; Auto-Answer is disabled.

GUARD TONE

Type:

Configuration

Format:

AT [cmds] &Gn [cmds]

Description:

Commands the modem to transmit a guard tone in V.22/V.22bis

Command

Function

í &G0

Guard tone disabled

&G1

Guard tone disabled

&G2

1800Hz guard tone enabled

STORE ACTIVE PROFILE

Type:

Configuration

Format:

AT [cmds] &Wn [cmds]

Description:

Writes the values for the active profile into the non-volatile RAM

AUTO-RETRAIN - AUTO-FALLBACK/FALL-FORWARD

Type:

Configuration

Format:

AT [cmds] %En [cmds]

Description:

Controls auto-retrain mode and fallback/fall-forward

Command

Function

%E0

Auto-retrain disabled

%E1

Auto-retrain enabled

DSVD

Type:

Configuration

Format:

AT [cmds] �SSEn [cmds]

Description:

Controls the DSVD

Command

Function

-SSE0

Disabled

-SSE1

Enabled

DATA COMPRESSION

Type:

Configuration

Format:

AT [cmds] +DSn,m,o,p [cmds]

Description:

Controls the data compression

Command

Function

n=0

Negotiated; no compression

n=1

Data compression both directions, accept any direction

m=0

Do not disconnect if V.42bis is not negotiated by the remote modem as specified in n

o

Specifies the maximum number of dictionary entries (2048 entries) which should be negotiated

p

Specifies the maximum string length (32bytes) to be negotiated

ERROR CONTROL REPORING

Type:

Configuration

Format:

AT [cmds] +Ern [cmds]

Description:

Controls the whether or not the extended-format intermediate result code is transmitted from the modem to the DTE

Command

Function

+ER0

Disabled

+ER1

Enabled

LOCAL FLOW CONTROL

Type:

Configuration

Format:

AT [cmds] +IFCn [cmds]

Description:

Controls the modem local flow control

Command

Function

+IFC0

No flow control

+IFC1

XON/XOFF on transmitted data

+IFC2

Circuit 133

+IFC3

XON/XOFF on transmitted data with XON/XOFF characters being passed through to the remote modem.

LOCAL RATE REPORTING

Type:

Configuration

Format:

AT [cmds] +ILRRn [cmds]

Description:

Controls whether or not the extended-format information text is transmitted from the modem to the DTE

Command

Function

+ILRR0

Disabled

+ILRR1

Enabled

MANUFACTURER IDENTIFICATION

Type:

Configuration

Format:

AT [cmds] +GMIn [cmds]

Description:

Reports the modem manufacturer

MODEL IDENTIFICATION

Type:

Configuration

Format:

AT [cmds] +GMMn [cmds]

Description:

Reports the modem model identification

MODULATION REPORTING

Type:

Configuration

Format:

AT [cmds] +MRn [cmds]

Description:

Controls the modulation reporting

Command

Function

+MR0

Disabled

+MR1

Enabled

REVISION IDENTIFICATION

Type:

Configuration

Format:

AT [cmds] +GMRn [cmds]

Description:

Reports the modem version, revision level, or date.

VIDEO READY MODE

Type:

Configuration

Format:

AT [cmds] +Hn [cmds]

Description:

Controls the video ready mode

Command

Function

+H0

Disable video ready mode

+H16

Enabled video ready mode

FLASH DIAL MODIFIER TIME

Type:

Register

Format

AT [cmds] S29=n [cmds]

Default:

70

Range:

0-255

Unit:

.01 second

Description:

Time the modem will go on-hook upon receiving the ! dial modifier in dial string.