ACER, INC.
MAGIC F34
|
Card Type |
Modem/Fax card |
|
Chip Set |
Unidentified |
|
Maximum Modem Rate |
33.6Kbps |
|
Maximum Fax Rate |
14.4Kbps |
|
Data Modulation Protocol |
Bell 103/212A ITU-T V.22, V.22bis, V.23, V.32, V.32bis, V.34 |
|
Fax Modulation Protocol |
ITU-T V.17, V.33, V.29, V.27ter, V.21CH2 |
|
Error Correction/Compression |
MNP5, V.42, V.42bis |
|
Fax Class |
Class I & II |
|
Data Bus |
16-bit ISA |
|
Card Size |
Half length, full-height card |
|
CONNECTIONS | ||||||
|
Function |
Label |
Function |
Label | |||
|
Telephone line out |
CN1 |
Microphone |
CN4 | |||
|
Telephone line in |
CN2 |
Audio card connector |
CN5 | |||
|
Line out |
CN3 | |||||
|
SERIAL PORT ADDRESS | ||||
|
Setting |
JP2 |
JP3 |
JP4 |
JP5 |
|
COM1 |
1 & 2 |
2 & 3 |
2 & 3 |
2 & 3 |
|
COM2 |
2 & 3 |
1 & 2 |
2 & 3 |
1 & 2 |
|
í Plug and Play enabled |
1 & 2 |
Unidentified |
1 & 2 |
1 & 2 |
|
Note: Pins designated should be in the closed position. To use the plug and play option, the optional chip C1 must be installed. | ||||
|
SUPPORTED COMMAND SET |
|
Basic AT Commands |
|
AT, +++, A/ |
|
A, B, C, E, H, M, O, P, Q, T, V, W, X, Y, Z |
|
&C, &F, &M, &P, &Q, &T, &V, &W, &Y, &Z |
|
Extended AT Commands |
|
\A, \B, \K, \N, \V, |
|
%C, %E, %L, %Q, %TT |
|
S Registers |
|
S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S19, S20, S21, S22, S23, |
|
S24, S25, S26, S29, S30, S31, S32, S33, S36, S37, S38, S39, S40, S41, S46, S48, S82, S86, S91, |
|
S92, S95 |
|
Special Commands |
|
#CID, +MS?, +MS, #BDR, #CLS, #MDL?, #MFR?, #REV?, #TL, #VBQ, #VBS, #VBT, #VCI?, #VLS, |
|
#VRA, #VRN, #VRX, #VSD, #VSK, #VSP, #VSR, #VSS, #VTD, #VTM, #VTS, #VTX |
|
Note: See MHI Help File for full command documentation. |
Proprietary AT Command Set
|
AUTO-MODE DETECTION | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Nn [cmds] |
|
Description: |
Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed. |
|
Command |
Function |
|
N0 |
Auto-mode detection disabled |
|
N1 |
Auto-mode detection enabled |
|
BLACKLISTED NUMBERS | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] *B [cmds] |
|
Description: |
Sends the list of blacklisted numbers to the DTE. If no numbers are blacklisted, the OK result code is sent |
|
DATA SET READY (DSR) | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Sn [cmds] |
|
Description: |
Selects DSR options |
|
Command |
Function |
|
&S0 |
DSR forced high |
|
&S1 |
DSR high only while modem is handshaking or connected |
|
DATA TERMINAL READY (DTR) | |||||
|
Type: |
Configuration | ||||
|
Format: |
AT [cmds] &Dn [cmds] | ||||
|
Description: |
Selects modem response to DTR | ||||
Note: The action each variant of &D causes depends on the setting of &Q | |||||
|
&Q Setting |
&D0 |
&D1 |
&D2 |
&D3 | |
|
&Q0, &Q5, &Q6 |
Command 0 |
Command 1 |
Command 2 |
Command 3 | |
|
&Q1, &Q4 |
Command 4 |
Command 1 |
Command 2 |
Command 3 | |
|
&Q2, &Q3 |
Command 2 |
Command 2 |
Command 2 |
Command 2 | |
|
Command |
Function | ||||
|
Command 0 |
Modem does not respond to DTR | ||||
|
Command 1 |
Modem goes to command mode after DTR goes off | ||||
|
Command 2 |
Modem goes to command mode and disconnects (hangs up) after DTR goes off; Auto-Answer is disabled. | ||||
|
Command 3 |
Modem is initialized after DTR goes off | ||||
|
Command 4 |
Modem goes to command mode and disconnects (hangs up) after DTR goes off. | ||||
|
DIAL | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] D<#> [cmds] |
|
Description: |
Dials telephone number according to any modifiers included in the string |
|
Note: |
Any combination of modifiers can be used to produce the desired dial functions in sequence. |
|
Command |
Function |
|
0-9 |
Dialing digits |
|
A, B, C, D, *, # |
Tone dial characters |
|
P |
Pulse dial |
|
R |
Reverse originate mode |
|
S=n |
Dial NVRAM telephone number |
|
T |
Tone dial |
|
W |
Wait for dial tone |
|
, |
Pause |
|
! |
Flash hook, modem goes on hook for .75 seconds |
|
@ |
Wait for quiet answer |
|
^ |
Disable data calling tone for a single call origination |
|
; |
Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command |
|
-( ) space |
Ignored by modem. The modem ignores these characters, but they can be included in the dial string for separation purposes |
|
FLOW CONTROL | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Kn [cmds] |
|
Description: |
Enables flow control options |
|
Command |
Function |
|
&K0 |
Flow control disabled |
|
&K3 |
RTS/CTS flow control enabled |
|
&K4 |
XON/XOFF flow control enabled |
|
&K5 |
Transparent XON/XOFF flow control enabled |
|
&K6 |
Unidirectional XON/XOFF flow control enabled |
|
GUARD TONE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Gn [cmds] |
|
Description: |
Commands the modem to transmit a guard tone in V.22/V.22bis |
Note: Used primarily for international data transmission | |
|
Command |
Function |
|
&G0 |
Guard tone disabled |
|
&G1 |
Guard tone disabled |
|
&G2 |
1800Hz guard tone enabled |
|
REPORT INFORMATION | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] In [cmds] |
|
Description: |
Displays information requested |
|
Command |
Function |
|
I0 |
Reports product code |
|
I1 |
Calculates and verifies the ROM checksum |
|
I2 |
Calculates and compares the ROM checksum with the pre-stored checksum |
|
I3 |
Reports the firmware version, basic model, application code, and interface type code |
|
I4 |
Reports OEM defined identifier string in either Hayes-compatible binary format or ASCII format |
|
I5 |
Reports country code |
|
I6 |
Reports modem data pump model and internal code revision |
|
SPEAKER VOLUME | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Ln [cmds] |
|
Description: |
Controls speaker volume |
|
Command |
Function |
|
L0 |
Low speaker volume |
|
L1 |
Low volume setting |
|
L2 |
Medium volume setting |
|
L3 |
Highest volume setting |