ATI TECHNOLOGIES, INC.
2400 ETC-I, 2400 ETC-FAX
|
Card Type |
Modem (synchronous/asynchronous) |
|
Chip Set |
ATI |
|
Maximum Data Rate |
2400bps |
|
Maximum Fax Rate |
9600bps |
|
Data Bus |
8-bit ISA |
|
Fax Class |
Class I |
|
Data Modulation Protocol |
Bell 103A/212A ITU-T V.22, V.22bis |
|
Fax Modulation Protocol |
ITU-T V.27ter, V.29 |
|
Error Correction/Compression |
MNP5, V.42, V.42bis |
|
CONNECTIONS | ||||||
|
Function |
Label |
Function |
Label | |||
|
Line in |
CN1 |
Line out |
CN2 | |||
|
SERIAL PORT ADDRESS | |||||
|
COM |
IRQ |
SW1/1 |
SW1/2 |
SW1/3 |
SW1/4 |
|
COM1: (3F8h) |
4 |
On |
Off |
Off |
Off |
|
í COM2: (2F8h) |
3 |
Off |
On |
Off |
Off |
|
COM3: (3E8h) |
4 |
Off |
Off |
On |
Off |
|
COM4: (2E8h) |
3 |
Off |
Off |
Off |
On |
|
COM1: (3F8h) |
Set by JP1 |
On |
Off |
Off |
Off |
|
COM2: (2F8h) |
Set by JP1 |
On |
Off |
On |
On |
|
COM3: (3E8h) |
Set by JP1 |
Off |
Off |
On |
Off |
|
COM4: (2E8h) |
Set by JP1 |
On |
On |
On |
Off |
|
INTERRUPT | ||||
|
Setting |
JP1/A |
JP1/B |
JP1/C |
JP1/D |
|
IRQ2 |
Closed |
Open |
Open |
Open |
|
IRQ3 |
Open |
Closed |
Open |
Open |
|
í IRQ4 or automatic |
Open |
Open |
Closed |
Open |
|
IRQ5 |
Open |
Open |
Open |
Closed |
Proprietary AT Command Set
|
AUTO-RELIABLE FALLBACK CHARACTER | |
|
Type: |
Register |
|
Format: |
AT [cmds] S46=n [cmds] |
|
Default: |
13 |
|
Range: |
0-127 |
|
Unit: |
1 ASCII character |
|
Description: |
Sets the character used as the auto-reliable fallback character. S46=0 will disable this function. |
|
BREAK TYPE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &In [cmds] |
|
Description: |
Sets the modems response to a break signal. |
|
Command |
Function |
|
í &I0 |
Send break with transmitted data. |
|
&I1 |
Send break to remote modem immediately. |
|
&I2 |
Send break to remote modem immediately, modem buffers cleared. |
|
DATA COMPRESSION | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Un [cmds] |
|
Description: |
Selects data compression. |
|
Command |
Function |
|
í &U0 |
Data compression disabled. |
|
&U1 |
Data compression enabled. |
|
FLOW CONTROL TYPE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Kn [cmds] |
|
Description: |
Enables flow control options. |
|
Command |
Function |
|
í &K0 |
Flow control disabled. |
|
&K3 |
RTS/CTS flow control enabled. |
|
&K4 |
XON/XOFF flow control enabled. |
|
&K8 |
Transparent remote XON/XOFF flow control enabled. |
|
&K12 |
Transparent XON/XOFF flow control enabled. |
|
INACTIVITY TIMER | |
|
Type: |
Register |
|
Format: |
AT [cmds] S40=n [cmds] |
|
Default: |
0 |
|
Range: |
1-255 |
|
Unit: |
1 minute |
|
Description: |
Sets the length of time that the modem does not receive information before it disconnects. |
|
REDIAL ATTEMPTS | |
|
Type: |
Register |
|
Format: |
AT [cmds] S41=n [cmds] |
|
Default: |
0 |
|
Range: |
0-10 |
|
Unit: |
1 attempt |
|
Description: |
Sets the number of times the modem will attempt to redial a busy call. |