ANGIA COMMUNICATIONS, INC.
PCMCIA 14400BPS DATA/14400BPS FAX
|
Card Type |
Fax, Modem (asynchronous) |
|
Chip Set |
Unidentified |
|
Maximum Data Rate |
14.4Kbps |
|
Maximum Fax Rate |
14.4Kbps |
|
Data Bus |
PCMCIA Type II |
|
Fax Class |
Class I |
|
Data Modulation Protocol |
Bell 103/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis |
|
Fax Modulation Protocol |
ITU-T V.17, V.21CH2, V.27ter, V.29 |
|
Error Correction/Compression |
MNP5, V.42, V.42bis |
V2329
|
SUPPORTED COMMAND SET |
|
Basic AT Commands |
|
AT, +++, Comma, A/ |
|
A, B, C, D, E, F, H, L, M, O, P, Q, S, T, V, W, X, Y, Z |
|
&C, &D, &E, &G, &J, &L, &M, &P, &Q, &R, &T, &V, &W, &Y, &Z |
|
Extended AT Commands |
|
\A, \B, \C, \G, \J, \K, \N \Q, \V, \X, \Z, %A, %E |
|
S Registers |
|
S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S11, S12, S16, S18, S25, S26, S36 |
|
S38, S39, S46, S48 |
|
Note: See MHI Help file for full command documentation. |
Proprietary AT Command Set
|
BIT MAPPED REGISTERS | |
|
Register |
Default |
|
S14 |
Read-only |
|
S19 |
26 |
|
S20 |
32 |
|
S21 |
Read-only |
|
S22 |
Read-only |
|
S23 |
Read-only |
|
S27 |
Read-only |
|
COMPRESSION | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] %Cn [cmds] |
|
Description: |
Selects data compression |
|
Command |
Function |
|
%C0 |
Data compression disabled |
|
%C1 |
Data compression enabled; V.42bis during LAPM, MNP5 during MNP |
|
CONNECT MODE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Nn [cmds] |
|
Description: |
Controls the type of connection the modem will operate in |
|
Command |
Function |
|
\N0 |
Direct mode enabled |
|
\N1 |
Normal mode enabled |
|
\N2 |
MNP reliable mode enabled |
|
\N3 |
MNP auto-reliable mode enabled |
|
\N4 |
V.42 reliable mode enabled |
|
\N5 |
V.42 auto-reliable mode enabled |
|
\N6 |
Reliable mode enabled |
|
í \N7 |
Auto-reliable mode enabled |
|
DISPLAY FIRMWARE VERSION | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] %V [cmds] |
|
Description: |
Displays firmware version information |
|
ENQ/ACK | ||
|
Type: |
Configuration | |
|
Format: |
AT [cmds] \Hn [cmds] | |
|
Description: |
Controls Hewlett Packard ENQ/ACK protocol | |
|
Command |
Function | |
|
í \H0 |
Hewlett Packard ENQ/ACK disabled | |
|
\H1 |
Hewlett Packard ENQ/ACK emulating terminal enabled | |
|
\H2 |
Hewlett Packard ENQ/ACK emulating host | |
|
FACTORY DEFAULT PROFILE | ||
|
Type: |
Configuration | |
|
Format: |
AT [cmds] &F [cmds] | |
|
Description: |
Sets values in active profile to values found in the default profile | |
|
Command |
Function | |
|
&F0 |
Restore auto-reliable compression/correction default profile | |
|
&F1 |
Restore auto-reliable compression/correction default profile | |
|
INACTIVITY TIMER | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Tn [cmds] |
|
Default: |
0 |
|
Range: |
0-90 |
|
Unit: |
1 minute |
|
Description: |
Sets the length of time that the modem does not receive information before it disconnects. |
|
MINIMUM MODEM PORT RATE | ||
|
Type: |
Configuration | |
|
Format: |
AT [cmds] %Mn [cmds] | |
|
Description: |
Selects the minimum modem port rate | |
|
Command |
Function | |
|
í %M300 |
300bps selected | |
|
%M1200 |
1200bps selected | |
|
%M2400 |
2400bps selected | |
|
%M4800 |
4800bps selected | |
|
%M7200 |
7200bps selected | |
|
%M9600 |
9600bps selected | |
|
%M12000 |
12000bps selected | |
|
%M14400 |
14400bps selected | |
|
MODEM PORT RATE | ||
|
Type: |
Configuration | |
|
Format: |
AT [cmds] %Bn [cmds] | |
|
Description: |
Selects the modem port rate | |
|
Command |
Function | |
|
%B300 |
300bps selected | |
|
%B1200 |
1200bps selected | |
|
%B2400 |
2400bps selected | |
|
%B4800 |
4800bps selected | |
|
%B7200 |
7200bps selected | |
|
%B9600 |
9600bps selected | |
|
%B12000 |
12000bps selected | |
|
í %B14400 |
14400bps selected | |
|
REPORT INFORMATION | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] In [cmds] |
|
Description: |
Displays information requested |
|
Command |
Function |
|
I0 |
Reports product code |
|
I1 |
Reports ROM checksum |
|
I2 |
Reports OK |
|
I3 |
Reports a date code |