IPTools.net.ua

Modem Type

Data (synchronous/asynchronous)/Fax

Maximum Data Rate

14.4Kbps

Maximum Fax Rate

14.4Kbps

Data Bus

External

Fax Class

Class I & II

Data Modulation Protocol

ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis

Fax Modulation Protocol

ITU-T V.17, V.21CH2, V.27ter, V.29

Error Correction/Compression

MNP5, V.42, V.42bis

CONNECTIONS

Purpose

Location

Purpose

Location

Line out

CN1

DC power

CN4

Line in

CN2

Power switch

SW1

RS-232/422

CN3

DIAGNOSTIC LED(S)

LED

Color

Status

Condition

MR

Red

On

Power is on

MR

Red

Off

Power is off

TR

Red

On

DTR signal is high

TR

Red

Off

DTR signal is low

SD

Red

Blinking

Modem is transmitting data

SD

Red

Off

Modem is not transmitting data

RD

Red

Blinking

Modem is receiving data

RD

Red

Off

Modem is not receiving data

OH

Red

On

Modem is off-hook

OH

Red

Off

Modem is on-hook

CD

Red

On

Carrier signal detected

CD

Red

Off

Carrier signal not detected

AA

Red

On

Auto-answer enabled

AA

Red

Off

Auto-answer disabled

AA

Red

Blinking

Phone is ringing

HS

Red

Blinking

Modem is in test mode or detected an error

HS

Red

On

Modem is operating at 9600bps or faster

HS

Red

Off

Modem is not operating faster than 9600bps

ACCEPT RELIABLE MODE

Type:

Immediate

Format:

AT [cmds] \U [cmds]

Example:

AT \U B1<CR>

Description:

Accepts remote modem�s request for reliable link.

AUTO-RETRAIN

Type:

Configuration

Format:

AT %En

Example:

AT %E1 <CR>

Description:

Selects auto-retrain mode.

Function

Auto-retrain disabled.

Auto-retrain enabled.

BTI-MAPPED REGISTERS

Register

Default

S14

Unidentified

S21

Unidentified

S22

Unidentified

S23

Unidentified

S27

Unidentified

S40

57

S41

1

BREAK SEND

Type:

Configuration

Format:

AT [cmds] \Bn [cmds]

Example:

AT \B3 &W<CR>

Default:

3

Range:

1-9

Unit:

.1 second

Description:

Sends break to modem.

BREAK TYPE

Type:

Configuration

Format:

AT [cmds] \Kn [cmds]

Example:

AT \K5 <CR>

Description:

Configures action of break signal.

Function

Online command mode enabled, send no break to remote modem.

Break sent to remote modem and buffered cleared.

Send break to remote modem immediately.

Send break with transmitted data.

COMPRESSION

Type:

Configuration

Format:

AT [cmds] %Cn [cmds]

Example:

AT %C1 <CR>

Description:

Selects data compression.

Function

Data compression disabled.

Data compression enabled.

COMPRESSION

Type:

Configuration

Format:

AT [cmds] %Mn [cmds]

Example:

AT %M3 <CR>

Description:

Selects data compression.

Function

Data compression disabled.

Data compression enabled on transmit only.

Data compression enabled on receive only.

Data compression enabled.

CONNECT MODE

Type:

Configuration

Format:

AT [cmds] \Nn [cmds]

Example:

AT \N1 DT555-1212<CR>

Description:

Sets connect mode.

Function

Normal mode enabled.

Direct mode enabled.

Reliable mode enabled.

Auto-reliable mode enabled.

CONVERT TO RELIABLE MODE

Type:

Immediate

Format:

AT [cmds] \Y [cmds]

Example:

AT \Y<CR>

Description:

Initiates reliable mode link.

ECHO OPTIMIZATION

Type:

Immediate

Format:

AT [cmds] \En [cmds]

Example:

AT \E1 <CR>

Description:

Enables modem echo optimization.

Command

Function

\E1

One shot optimization enabled.

FLOW CONTROL

Type:

Configuration

Format:

AT [cmds] \Gn [cmds]

Example:

AT \G0 &K3<CR>

Description:

Selects modem port flow control.

Function

Flow control disabled.

Flow control enabled.

INACTIVITY TIMER

Type:

Configuration

Format:

AT [cmds] \Tn [cmds]

Example:

AT\T0<CR>

Default:

0

Range:

0-90

Unit:

1 minute

Description:

Sets the length of time that the modem does not receive information before it disconnects.

LINE SIGNAL LEVEL

Type:

Immediate

Format:

AT [cmds] %L [cmds]

Example:

AT %L &W<CR>

Description:

Returns recieved line signal level.

MAXIMUM BLOCK SIZE FOR TRANSMISSION

Type:

Configuration

Format:

AT [cmds] \An [cmds]

Example:

AT \A2 &MB28800<CR>

Description:

Sets the maximum transmittable block size.

Function

Maximum MNP block size is 64 characters.

Maximum MNP block size is 128 characters.

Maximum MNP block size is 192 characters.

Maximum MNP block size is 256 characters.

MNP STREAM/BLOCK MODE

Type:

Configuration

Format:

AT [cmds] \Ln [cmds]

Example:

AT \L1 DT555-1212<CR>

Description:

Selects the transfer mode for MNP.

Function

Stream mode for MNP enabled.

Block mode for MNP enabled.

ON-LINE IN RELIABLE MODE

Type:

Immediate

Format:

AT [cmds] \O

Example:

AT \O <CR>

Description:

Returns to on-line and requests reliable mode connection.

REPORT SIGNAL QUALITY

Type:

Immediate

Format:

AT [cmds] %Q [cmds]

Example:

AT %Q &W<CR>

Description:

Reports signal quality.

SWITCH TO MNP MODE

Type:

Immediate

Format:

AT [cmds] \Z [cmds]

Example:

AT \Z &W<CR>

Description:

Switches to normal mode from MNP mode.

TEST MODES

Format

AT [cmds] S16=n [cmds]

Example:

ATS16=0<CR>

Default:

0

Range:

0-125

Unit:

Bit-mapped

Description:

Controls loopback tests, analog, digital, remote digital, and self tests.

Bit

Value

Function

0

1

Local analog loopback in progress.

1

0

Not used.

2

1

Local digital loopback in progress.

3

1

Remote digital loopback in progress.

4

1

Remote digital loopback requested.

5

1

Remote digital loopback w/ self-test in progress.

6

1

Local analog loopback w/ self-test in progress.

V.42bis DICTIONARY CLEAR

Type:

Immediate

Format:

AT [cmds] %P [cmds]

Example:

AT %P &W<CR>

Description:

Clears V.42bis dictionary.

V.42bis DICTIONARY SIZE

Type:

Configuration

Format:

AT [cmds] %Dn [cmds]

Example:

AT %D2 &W<CR>

Description:

Controls V.42bis dictionary size.

Function

512 bytes.

1024 bytes.

2048 bytes

4096 bytes (one way compression only)

V.42bis MAXIMUM STRING LENGTH

Type:

Configuration

Format:

AT [cmds] %Sn [cmds]

Example:

AT %S32 <CR>

Default:

32

Range:

6 - 64

Unit:

Unidentified

Description:

Selects string size for V.42bis compression.