ARCHTEK AMERICA CORPORATION
1914BAV
|
Modem Type |
Data (synchronous/asynchronous)/Fax/Voice |
|
Maximum Data Rate |
19.2Kbps |
|
Maximum Fax Rate |
14.4Kbps |
|
Data Bus |
8-bit ISA |
|
Fax Class |
Class I |
|
Data Modulation Protocol |
Bell 103J/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis AT&T V.32terbo |
|
Fax Modulation Protocol |
ITU-T V.17, V.21CH2, V.27ter, V.29 |
|
Error Correction/Compression |
MNP5, V.42, V.42bis |
|
CONNECTIONS | |||
|
Purpose |
Location |
Purpose |
Location |
|
Line out |
CN1 |
Speaker line out |
CN4 |
|
Line in |
CN2 |
Microphone line in |
CN5 |
|
Audio line in |
CN3 | ||
|
BASE I/O ADDRESS SELECTION | |||
|
Port |
JP1 pins 7 & 8 |
JP1 pins 9 & 10 |
JP1 pins 11 & 12 |
| COM1: (100h) |
Open |
Open |
Open |
|
í COM2: (180h) |
Open |
Closed |
Open |
|
í COM3: (280h) |
Closed |
Open |
Closed |
|
í COM4: (300h) |
Closed |
Closed |
Open |
|
í COM5: (380h) |
Closed |
Closed |
Closed |
|
INTERRUPT SELECTION | |||
|
IRQ |
JP1 pins 1 & 2 |
JP pins 3 & 4 |
JP1 pins 5 & 6 |
|
í 5 |
Open |
Open |
Closed |
|
í 7 |
Open |
Closed |
Open |
| 9 |
Closed |
Open |
Open |
Proprietary AT Command Set
|
CALLING TONE | |
|
Type: |
Register |
|
Format: |
AT [cmds] S35=n [cmds] |
|
Example: |
AT S35=1 DT555-1212<CR> |
|
Description: |
Controls the transmission of the calling tone while dialing. |
|
í Command |
Function |
|
í S35=0 |
Calling tone disabled. |
| S35=1 |
Calling tone enabled. |
|
COMPRESSION | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] %Cn [cmds] |
|
Example: |
AT %C0 <CR> |
|
Description: |
Selects data compression. |
|
í Command |
Function |
|
í %C0 |
Data compression disabled. |
| %C1 |
Data compression enabled. |
|
COMPRESSION | |
|
Type: |
Configuration |
|
Format: |
AT "Hn |
|
Example: |
AT %C0 "H0 <CR> |
|
Description: |
Selects data compression. |
|
í Command |
Function |
|
í "H0 |
Data compression disabled. |
| "H1 |
Data compression enabled. |
|
CONNECT MODE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Nn [cmds] |
|
Example: |
AT \N0 DT555-1212 <CR> |
|
Description: |
Sets connect mode. |
|
Command |
Function |
|
í \N0 |
Normal mode enabled. |
|
í \N1 |
Direct mode enabled. |
|
í \N2 |
Reliable mode enabled. |
| \N3 |
Auto-reliable mode enabled. |
|
í \N4 |
LAPM mode enabled. |