TANDBERG DATA
TDC 3620, TDC 3640, TDC 3660 (VER. 2)
|
Device Type |
Tape Drive |
|
Interface |
SCSI-2 |
|
Format |
QIC-24 (TDC3620), QIC-120 (TDC3640), QIC-150 (TDC3660 VER. 2) |
|
Sustained Transfer Rate |
Unidentified |
|
Size |
5.25 in. half height |
|
View |
Top |
|
CONNECTIONS | |
|
Function |
Label |
|
Ground connector |
CN1 |
|
Note: CN1 not present on all models. | |
|
USER CONFIGURABLE SETTINGS | |||
|
Setting |
Label |
Position | |
|
Factory configured - do not alter. (Serial communication out) |
JP1/Pins 1 & 2 |
Unidentified | |
|
Factory configured - do not alter. (Serial communication in) |
JP1/Pins 3 & 4 |
Unidentified | |
|
Parity check enabled |
JP1/Pins 5 & 6 |
Closed | |
|
Parity check disabled |
JP1/Pins 5 & 6 |
Open | |
|
DRIVE SELECT ID | ||||
|
Drive ID |
JP1/Pins 7 & 8 |
JP1/Pins 9 & 10 |
JP1/Pins 11 & 12 | |
|
0 |
Open |
Open |
Open | |
|
1 |
Open |
Open |
Closed | |
|
2 |
Open |
Closed |
Open | |
|
3 |
Open |
Closed |
Closed | |
|
4 |
Closed |
Open |
Open | |
|
5 |
Closed |
Open |
Closed | |
|
6 |
Closed |
Closed |
Open | |
|
7 |
Closed |
Closed |
Closed | |
|
Note: Pins 2 & 4 of JP1 must be open to enable SCSI ID select. With Pins 2 & 4 of JP1 closed, factory test functions are enabled via pins 7-12. | ||||
|
MANUFACTURERS RECOMMENED MEDIA | |||
|
Drive |
Tape |
Capacity Without Compression |
Capacity With Compression |
|
TDC 3620 |
3M® DC300XL 137m |
45MB |
Unidentified |
|
TDC 3620 |
3M® DC300XLP 137m |
45MB |
Unidentified |
|
TDC 3620 |
DEI 169m |
55MB |
Unidentified |
|
TDC 3620 |
DEI Ser. II Gold Plus 169m |
55MB |
Unidentified |
|
TDC 3620 |
3M® DC600A 183m |
60MB |
Unidentified |
|
TDC 3620 |
3M® DC600XTD 183m |
60MB |
Unidentified |
|
TDC 3640 |
3M® DC600A 183m |
125MB |
Unidentified |
|
TDC 3640 |
3M® DC600XTD 183m |
125MB |
Unidentified |
|
TDC 3660 (VER. 2) |
3M® DC600A 183m |
125MB |
Unidentified |
|
TDC 3660 (VER. 2) |
3M® DC600XTD 183m |
125MB |
Unidentified |
|
TERMINATING RESISTOR CONFIGURATION | |||
|
Function |
RP1 |
RP2 |
RP3 |
|
Termination enabled |
Terminator installed |
Terminator installed |
Terminator installed |
|
Termination disabled |
Terminator not installed |
Terminator not installed |
Terminator not installed |
|
DIAGNOSTIC LED(S) | |||||||
|
LED1 (Red) Blink-Code* |
Condition |
Fatal Error | |||||
|
Short |
Short |
Short |
Short |
Short |
Short |
No error | |
|
Short |
Short |
Short |
Short |
Short |
Long |
Append error | |
|
Short |
Short |
Short |
Short |
Long |
Short |
Bad command block | |
|
Short |
Short |
Short |
Short |
Long |
Long |
Bad parameter block | |
|
Short |
Short |
Short |
Long |
Short |
Short |
Bus parity error | |
|
Short |
Short |
Short |
Long |
Short |
Long |
Busy | |
|
Short |
Short |
Short |
Long |
Long |
Short |
Capst. servo error |
B |
|
Short |
Short |
Short |
Long |
Long |
Long |
Cartridge removed | |
|
Short |
Short |
Long |
Short |
Short |
Short |
Compare error | |
|
Short |
Short |
Long |
Short |
Short |
Long |
Copy data error | |
|
Short |
Short |
Long |
Short |
Long |
Short |
Copy managem. error | |
|
Short |
Short |
Long |
Short |
Long |
Long |
File mark error | |
|
Short |
Short |
Long |
Long |
Short |
Short |
Head servo error |
B |
|
Short |
Short |
Long |
Long |
Short |
Long |
Illegal command | |
|
Short |
Short |
Long |
Long |
Long |
Short |
Illeagal copy | |
|
Short |
Short |
Long |
Long |
Long |
Long |
Illegal length | |
|
Short |
Long |
Short |
Short |
Short |
Short |
Inappropriate request | |
|
Short |
Long |
Short |
Short |
Short |
Long |
Latch error |
A |
|
Short |
Long |
Short |
Short |
Long |
Short |
No cartridge | |
|
Short |
Long |
Short |
Short |
Long |
Long |
Not loaded | |
|
Short |
Long |
Short |
Long |
Short |
Short |
Power-on request | |
|
Short |
Long |
Short |
Long |
Short |
Long |
QIC. No data detected | |
|
Short |
Long |
Short |
Long |
Long |
Short |
Read after write error | |
|
Short |
Long |
Short |
Long |
Long |
Long |
Read EOM logical | |
|
Short |
Long |
Long |
Short |
Short |
Short |
Read EOM physical | |
|
Short |
Long |
Long |
Short |
Short |
Long |
Reserv. Conflict | |
|
Short |
Long |
Long |
Short |
Long |
Short |
Sensor error |
B |
|
Short |
Long |
Long |
Short |
Long |
Long |
Tape runnout |
B |
|
Short |
Long |
Long |
Long |
Short |
Short |
Unit attention | |
|
Short |
Long |
Long |
Long |
Short |
Long |
Write EOM warning | |
|
Short |
Long |
Long |
Long |
Long |
Short |
Write EOM | |
|
Short |
Long |
Long |
Long |
Long |
Long |
Cartridge write prot. | |
|
Long |
Short |
Short |
Short |
Short |
Short |
16 rewrite errors | |
|
Long |
Short |
Short |
Short |
Short |
Long |
24 rereads. Blk. fnd. | |
|
Long |
Short |
Short |
Short |
Long |
Short |
24 rereads. Not fnd. | |
|
Long |
Short |
Short |
Short |
Long |
Long |
Illegal copy function | |
|
Long |
Short |
Short |
Long |
Short |
Short |
Illegal header | |
|
Long |
Short |
Short |
Long |
Short |
Long |
No header | |
|
Long |
Short |
Short |
Long |
Long |
Short |
Too large address | |
|
Long |
Short |
Short |
Long |
Long |
Long |
Bad ID or LUN | |
|
Long |
Short |
Long |
Short |
Short |
Short |
Partial Description | |
|
Long |
Short |
Long |
Short |
Short |
Long |
Bad target status | |
|
Long |
Short |
Long |
Short |
Long |
Short |
Check condition | |
|
Long |
Short |
Long |
Short |
Long |
Long |
Data transfer error | |
|
Long |
Short |
Long |
Long |
Short |
Short |
Selection failure | |
|
DIAGNOSTIC LED(S) CONTINUED | |||||||
|
LED1 (Red) Blink-Code* |
Condition |
Fatal Error | |||||
|
Long |
Short |
Long |
Long |
Short |
Long |
Sequence error | |
|
Long |
Short |
Long |
Long |
Long |
Short |
Illegal block size | |
|
Long |
Long |
Short |
Short |
Short |
Long |
Buffer size error |
A |
|
Long |
Long |
Short |
Short |
Long |
Short |
Rereads outside limits | |
|
Long |
Long |
Short |
Short |
Long |
Long |
Rewrites outside limits | |
|
Long |
Long |
Short |
Long |
Short |
Short |
Buffer error. Low nibble |
A |
|
Long |
Long |
Short |
Long |
Short |
Long |
Buffer error. High nibble |
A |
|
Long |
Long |
Short |
Long |
Long |
Short |
Unspec. fatal error | |
|
Long |
Long |
Short |
Long |
Long |
Long |
Timeout error |
B |
|
Long |
Long |
Long |
Short |
Short |
Short |
Buffer RAM error |
A |
|
Long |
Long |
Long |
Short |
Short |
Long |
Drive contr. Error |
A |
|
Long |
Long |
Long |
Short |
Long |
Short |
EEPROM verification |
A |
|
Long |
Long |
Long |
Short |
Long |
Long |
EEPROM error |
A |
|
Long |
Long |
Long |
Long |
Short |
Short |
External RAM error |
A |
|
Long |
Long |
Long |
Long |
Short |
Long |
SCSI contr. Error |
A |
|
Long |
Long |
Long |
Long |
Long |
Short |
Spurious interrupt |
B |
|
Long |
Long |
Long |
Long |
Long |
Long |
Stack overflow |
B |
|
Note: Type A Code: Error cannot be reset. Drive will continue to report error with a blinking code once initial error has occurred. Service is required. Type B Code: Errors are failures in the Drive or the cartridge. Error can be cleared by RESET and information saved in EEPROM. | |||||||
.