QUANTUM CORPORATION
DLT 4000 (INTERNAL)
|
Device Type |
Internal Tape Drive |
|
Interface |
SCSI-2 Fast Wide |
|
Format |
DLT |
|
Sustained Transfer Rate |
1.5 MBPS 3.0 MBPS (compressed) |
|
Size |
5.25 in. full height |
|
View |
Top |
|
CONNECTIONS | |
|
Function |
Label |
|
Proprietary Power connector |
CN1 |
|
USER CONFIGURABLE SETTINGS | |||
|
Setting |
Label |
Position | |
|
Factory configured - do not alter. |
JP1/Pins 1 & 2 |
Unidentified | |
|
Factory configured - do not alter. |
JP1/Pins 5 - 26 |
Unidentified | |
|
Factory configured - do not alter. |
JP2/Pins 1 - 26 |
Unidentified | |
|
Factory configured - do not alter. |
JP3/Pins 1 - 6 |
Unidentified | |
|
Remote ID enabled |
JP4/Pins 1 & 2 |
Closed | |
|
Remote ID disabled |
JP4/Pins 1 & 2 |
Open | |
|
Parity check disabled |
JP4/Pins 3 & 4 |
Closed | |
|
Parity check enabled |
JP4/Pins 3 & 4 |
Open | |
|
Factory configured - do not alter. (Loader Connector) |
JP5/Pins 1 - 10 |
Unidentified | |
|
DRIVE SELECT ID | |||
|
Drive ID |
JP4/Pins 5 & 6 |
JP4/Pins 7 & 8 |
JP4/Pins 9 & 10 |
|
0 |
Open |
Open |
Open |
|
1 |
Open |
Open |
Closed |
|
2 |
Open |
Closed |
Open |
|
3 |
Open |
Closed |
Closed |
|
4 |
Closed |
Open |
Open |
|
5 |
Closed |
Open |
Closed |
|
6 |
Closed |
Closed |
Open |
|
7 |
Closed |
Closed |
Closed |
|
Note: Pins 1 & 2 of JP4 are to be closed when selecting SCSI IDs. | |||
|
TERMINATION POWER SELECTION | ||
|
Setting |
JP1/Pins 3 & 4 | |
|
TERMPWR supplied by drive |
Closed | |
|
TERMPWR supplied by SCSI interface to drive |
Open | |
|
MANUFACTURERS RECOMMENDED MEDIA | ||
|
Tape |
Capacity Without Compression |
Capacity With Compression |
|
DLT tape III 1100ft. |
10GB |
20GB |
|
DLT tape IIIxt 1800ft. |
15GB |
35GB |
|
DLT tape IV 1800ft. |
20GB |
40GB |
|
DIAGNOSTIC LED(S) | |||
|
LED |
Color |
Status |
Condition |
|
Write Protect |
Orange |
On |
Cartridge is write-protected. |
|
Write Protect |
Orange |
Off |
Cartridge is write-enabled. |
|
Tape In Use |
Yellow |
Blinking |
Cartridge is loaded and tape is moving. |
|
Tape In Use |
Yellow |
On |
Cartridge is loaded and ready for use. |
|
Use Cleaning Tape |
Yellow |
On |
Drive head requires cleaning, or tape is bad. |
|
Use Cleaning Tape |
Yellow |
Remains on after cleaning tape unloaded |
Cleaning tap attempted to clean drive head, tape expired, cleaning not performed. |
|
Use Cleaning Tape |
Yellow |
Turns on when data cartridge loaded after cleaning |
Problem data cartridge. Attempt different cartridge. |
|
Use Cleaning Tape |
Yellow |
Off |
Cleaning complete, or cleaning unnecessary. |
|
Operate Handle |
Green |
On |
Okay to operate cartridge insert/release handle |
|
Operate Handle |
Green |
Off |
Do not operate cartridge insert/release handle |
|
Operate Handle |
Green |
Blinking |
Close handle and wait for steady green indication before inserting cartridge. |
|
2.6 |
Yellow |
On |
Indicates tape is recorded in 2.6GB format. |
|
2.6 |
Yellow |
Blinking |
Indicates tape is recorded in another density selected for a write from BOT. |
|
6.0 |
Yellow |
On |
Indicates tape is recorded in 6.0GB format. |
|
6.0 |
Yellow |
Blinking |
Indicates tape is recorded in another density selected for a write from BOT. |
|
10.0/15.0 |
Yellow |
On |
Indicates tape is recorded in 10.0GB format if DLT™ tape III is used. Indicates tape is recorded in 15.0GB format if DLT™ tape IIIxt is used. |
|
10.0/15.0 |
Yellow |
Blinking |
Indicates tape is recorded in another density selected for a write from BOT. |
|
20.0 |
Yellow |
On |
Indicates tape is recorded in 20.0GB format. |
|
DIAGNOSTIC LED(S) | |||
|
LED |
Color |
Status |
Condition |
|
20.0 |
Yellow |
Blinking |
Indicates tape is recorded in another density selected for a write from BOT. |
|
Compress |
Yellow |
On |
Compression mode enabled (10.0, 15.0, and 35.0GB densities only). |
|
Compress |
Yellow |
Off |
Compression mode disabled. |
|
Density Override |
Yellow |
On |
Density from front panel selected. Density to be selected by the host (automatic). |
|
Density Override |
Yellow |
Off |
You are in density selection mode. |
|
Note: All four right side or all seven left side indicators On designates that the Power-on self-test (POST) is starting. All four right side or all seven left side indicators Blinking designates that an error has occurred in the POST; clear the error by pressing the unload button, or turn drive power off and then on again. If error remains service is required. | |||