PROTEON, INC.
PRONET-4/16 MODEL P1390
|
NIC Type |
Token-Ring |
|
Transfer Rate |
4/16Mbps |
|
Data Bus |
16-bit ISA |
|
Topology |
Ring |
|
Wiring Type |
Unshielded twisted pair Shielded twisted pair |
|
Boot ROM |
Available |
|
BOOT ROM | ||
|
Setting |
JP1 | |
|
Disabled |
Closed | |
|
Enabled |
Open | |
|
INTERRUPT REQUEST | |||||||||
|
IRQ |
JP2A |
JP2B |
JP2C |
JP2D |
JP2E |
JP2F |
JP2G |
JP2H |
JP2I |
|
2/9 |
Open |
Open |
Open |
Closed |
Open |
Open |
Open |
Open |
Open |
|
3 |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Closed |
|
4 |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Closed |
Open |
|
5 |
Open |
Open |
Open |
Open |
Open |
Open |
Closed |
Open |
Open |
|
6 |
Open |
Open |
Open |
Open |
Open |
Closed |
Open |
Open |
Open |
|
7 |
Open |
Open |
Open |
Open |
Closed |
Open |
Open |
Open |
Open |
|
10 |
Open |
Open |
Closed |
Open |
Open |
Open |
Open |
Open |
Open |
|
11 |
Open |
Closed |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
|
12 |
Closed |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
|
SA ADDRESS ENABLE (SAEN) | ||
|
Mode |
JP3 | |
|
SAEN enabled |
Closed | |
|
SAEN disabled |
Open | |
|
Note:The SAEN jumper is provided for systems that are not 100% ISA compatible. If the you get a DMA data error or if the card fails to initialize, you should disabled SAEN.
| ||
|
I/O BASE ADDRESS | |||||||||
|
Address |
JP4A |
JP4B |
JP4C |
JP4D |
JP4E |
JP4F |
JP4G |
JP4H | |
|
0120h |
Closed |
Closed |
Closed |
Closed |
Closed |
Closed |
Closed |
Open | |
|
0220h |
Closed |
Closed |
Closed |
Closed |
Closed |
Closed |
Open |
Closed | |
|
0320h |
Closed |
Closed |
Closed |
Closed |
Closed |
Closed |
Open |
Open | |
|
0420h |
Closed |
Closed |
Closed |
Closed |
Closed |
Open |
Closed |
Closed | |
|
0A20h |
Closed |
Closed |
Closed |
Closed |
Open |
Closed |
Open |
Closed | |
|
FC20h |
Open |
Open |
Open |
Open |
Open |
Open |
Closed |
Closed | |
|
FD20h |
Open |
Open |
Open |
Open |
Open |
Open |
Closed |
Open | |
|
FE20h |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Closed | |
|
FF20h |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Open | |
|
Note: A total of 255 I/O address settings are available. The switches are a binary representation of the two most significant digits in the Hexadecimal I/O address, the two least significant bits are set at 0020h. JP4H is the Least Significant Bit and JP4A is the Most Significant Bit. The jumpers have the following decimal values: jumper H=1, G=2, F=4, E=8, D=16, C=32, B=64, A=128. open the jumpers and add the values of the open jumpers. Convert that number to a hexadecimal number, and use it as the two left most digits in the numer "xx20h". If using Banyan VINES network, the I/O addresses are limited to the range between and including 0120h to 0F20h. | |||||||||
|
DMA CHANNEL | ||||
|
Channel |
JP5A & JP5B |
JP5C & JP5D |
JP5E & JP5F | |
|
DMA5 |
Open |
Open |
Closed | |
|
DMA6 |
Open |
Closed |
Open | |
|
DMA7 |
Closed |
Open |
Open | |
|
DMA CLOCK | |||||
|
Speed |
JP6A |
JP6B |
JP6C |
JP6D | |
|
Bus speed |
Open |
Open |
Open |
Closed | |
|
4MHz |
Open |
Open |
Closed |
Open | |
|
8MHz |
Open |
Closed |
Open |
Open | |
|
16MHz |
Closed |
Open |
Open |
Open | |