OLICOM, INC.
OC-3230 TR/MODEM 144
|
Card Type |
Modem(asynchronous), Fax, NIC |
|
Chip Set |
Texas Instruments TMS 380C25 |
|
Maximum Onboard Memory |
32KB, 128KB for LAN buffers |
|
Network Rate |
4/16Mbps |
|
Maximum Data Rate |
14.4Kbps |
|
Maximum Fax Rate |
14.4Kbps |
|
Data Bus |
PCMCIA Type II |
|
Fax Class |
Class I & II |
|
Data Modulation Protocol |
Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis |
|
Fax Modulation Protocol |
Unidentified |
|
Error Correction/Compression |
MNP10, V.42bis |
|
Topology |
Token Ring |
|
Wiring Type |
Shielded/Unshielded twisted pair |
|
Boot ROM |
128KB PROM |
V1802/N1433
Proprietary AT Command Set
|
AUTO-RETRAIN - FALLBACK/FALLFORWARD | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] %E n [cmds] |
|
Description: |
Controls auto-retrain mode and fallback/fall forward. |
|
Command |
Function |
|
%E0 |
Auto-retrain disabled |
|
%E1 |
Auto-retrain enabled |
|
%E2 |
Auto-retrain and Fallback/fall forward enabled |
|
%E3 |
Auto-retrain and Fallback/fall forward with fast hang up enabled |
|
BREAK SEND | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \B n [cmds] |
|
Range: |
1-9 |
|
Unit: |
.1 second |
|
Description: |
Sends break of n to modem |
|
BREAK TYPE | |||
|
Type: |
Configuration | ||
|
Format: |
AT [cmds] \K n [cmds] | ||
|
Description: |
Configures action of break signal | ||
|
Command |
Break from DTE Reliable/Normal mode |
Modem receives \B |
Break from remote modem |
|
\K0 |
Enter command mode, do not send break to remote modem. |
Buffers cleared and break sent to remote modem. |
Buffers cleared and break sent to DTE. |
|
\K1 |
Buffers cleared and break sent to remote modem. |
Buffers cleared and break sent to remote modem. |
Buffers cleared and break sent to DTE. |
|
\K2 |
Enter command mode, do not send break to remote modem. |
Send break to remote modem immediately. |
Send break to DTE immediately. |
|
\K3 |
Send break to remote modem immediately. |
Send break to remote modem immediately. |
Send break to DTE immediately. |
|
\K4 |
Enter command mode, do not send break to remote modem. |
Send break to remote modem with transmitted data. |
Break sent with received data to the DTE. |
|
\K5 |
Send break with transmitted data. |
Send break to remote modem with transmitted data. |
Break sent with received data to the DTE. |
|
CELLULAR TRANSMISSION LEVEL | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] @M n [cmds] |
|
Default: |
Unidentified |
|
Range: |
0 - 31 |
|
Unit: |
-1 dBm |
|
Description: |
Sets the signal level for transmission when in leased line mode |
|
CHANGE COUNTRY CODE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] *NC nn [cmds] |
|
Description: |
Changes country code to one of 8 stored in NVRAM |
|
COMPRESSION | |
|
Type: |
Configuration |
|
Format: |
AT %C n |
|
Description: |
Selects data compression. |
|
Command |
Function |
|
%C0 |
Data compression disabled |
|
%C1 |
MNP5 enabled |
|
%C2 |
V.42bis enabled |
|
%C3 |
MNP5 and V.42bis enabled |
|
COMPROMISE EQUALIZER | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] :E n [cmds] |
|
Description: |
Controls compromise equalizer |
|
Command |
Function |
|
:E0 |
Equalizer disabled |
|
:E1 |
Equalizer enabled |
|
CONNECT MODE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \N n [cmds] |
|
Description: |
Sets connect mode |
|
Command |
Function |
|
\N0 |
Normal mode enabled |
|
\N1 |
Direct mode enabled |
|
\N2 |
Reliable mode enabled |
|
\N3 |
Auto-reliable mode enabled |
|
\N4 |
LAPM mode only enabled |
|
\N5 |
MNP mode only enabled |
|
DISPLAY CURRENT CONFIGURATION | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] \S [cmds] |
|
Description: |
Displays current command profile |
|
DISPLAY DELAYED NUMBERS | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] *B [cmds] |
|
Description: |
Displays list of delayed numbers |
|
DISPLAY DELAYED NUMBERS | |
|
Type: |
Immediate |
|
Format: |
AT [cmds *D [cmds] |
|
Description: |
Displays list of of delayed numbers |
|
DISPLAY LINE SIGNAL LEVEL | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] %L [cmds] |
|
Description: |
Displays received line signal level in dBm |
|
DISPLAY LINE SIGNAL QUALITY | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] %Q [cmds] |
|
Description: |
Displays line signal quality |
|
DISPLAY STORED NUMBERS | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] \F [cmds] |
|
Description: |
Displays all stored phone numbers |
|
FALL-BACK | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] -Q n [cmds] |
|
Description: |
Enables fall back to V.22/V.22bis |
|
Command |
Function |
|
-Q0 |
V.22/V.22bis fall back enabled |
|
-Q1 |
V.22/V.22bis fall back disabled |
|
FLOW CONTROL | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \G n [cmds] |
|
Description: |
Enables modem port flow control |
|
Command |
Function |
|
\G0 |
Flow control disabled |
|
\G1 |
Flow control enabled |
|
LOCK SERIAL PORT | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \J n [cmds] |
|
Description: |
Sets operation of serial port speed |
|
Command |
Function |
|
\J0 |
Serial speed locked |
|
\J1 |
Serial speed follows connect speed |
|
MAXIMUM MNP BLOCK | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \A n [cmds] |
|
Description: |
Sets the maximum transmission block size |
|
Command |
Function |
|
\A0 |
MNP block size is 64 characters |
|
\A1 |
MNP block size is 128 characters |
|
\A2 |
MNP block size is 192 characters |
|
\A3 |
MNP block size is 256 characters |
|
MNP10 COMPRESSION | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] -K n [cmds] |
|
Description: |
Selects MNP10 data compression |
|
Command |
Function |
|
-K0 |
MNP10 disabled |
|
-K1 |
MNP10 enabled |
|
MNP 10 HANDSHAKE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] *H n [cmds] |
|
Description: |
Selects MNP 10 link negotiation speed |
|
Command |
Function |
|
*H0 |
MNP 10 handshake at highest common speed |
|
*H1 |
MNP 10 handshake at 1200bps |
|
*H2 |
MNP 10 handshake at 4800bps |
|
MNP10 POWER LEVEL ADJUST | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] )M n [cmds] |
|
Description: |
Controls automatic transmit power level adjustment during MNP 10 link negotiation |
|
Command |
Function |
|
)M0 |
Power level adjustment disabled |
|
)M1 |
Power level adjustment enabled |
|
MNP STREAM/BLOCK MODE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \L n [cmds] |
|
Description: |
Selects the transfer mode for MNP |
|
Command |
Function |
|
\L0 |
Stream mode for MNP enabled |
|
\L1 |
Block mode for MNP enabled |
|
PROTOCOL/SPEED | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] F n [cmds] |
|
Description: |
Selects protocol and line speed used |
|
Command |
Function |
|
F0 |
Select fastest common protocol |
|
F1 |
V.21/Bell 103A |
|
F3 |
Not used |
|
F3 |
V.23 |
|
F4 |
V.22/Bell 212A 1200bps |
|
F5 |
V.22bis 2400bps |
|
F6 |
V.32bis/V.32 4800bps |
|
F7 |
V.32bis 7200bps |
|
F8 |
V.32bis/V.32 9600bps |
|
F9 |
V.32bis 12.0Kbps |
|
F10 |
V.32bis 14.4Kbps |
|
PULSE DIAL CODE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] *Z n [cmds] |
|
Description: |
Selects digit used for pulse dial code |
|
Command |
Function |
|
*Z0 |
Use dial code 0 |
|
*Z1 |
Use dial code 1 |
|
REMOTE CONFIGURATION PASSWORD | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] *C n [cmds] |
|
Description: |
Store remote configuration password |
|
REMOTE MNP | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] *R [cmds] |
|
Description: |
Requests remote modems MNP configuration |
|
SETUP PASSWORD | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] *P xxxx / yyyy [cmds] |
|
Description: |
Changes the modems password and callback number. xxxx represents the password, and yyyy represents the callback number. |
|
V.23 SPLIT BAUD MODE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \W n [cmds] |
|
Description: |
Controls V.23 split baud mode |
|
Command |
Function |
|
\W0 |
V.23 split baud mode disabled |
|
\W1 |
V.23 split baud mode enabled |
|
VIEW DATA | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] %F n [cmds] |
|
Description: |
Selects split transmit and receive line speeds during viewdata operation |
|
Command |
Function |
|
%F1 |
75bps transmit/1200bps receive when viewdata selected |
|
%F2 |
1200bps transmit/75bps receive when viewdata selected |
|
S REGISTERS | ||
|
Register |
Function |
Default |
|
S14 |
Bit mapped |
Unidentified |
|
S16 |
Bit mapped test options |
Unidentified |
|
S20 |
Bit mapped |
Unidentified |
|
S21 |
Bit mapped |
Unidentified |
|
S22 |
Bit mapped speaker options |
Unidentified |
|
S23 |
Bit mapped |
Unidentified |
|
S24 |
Sleep inactivity timer |
0 |
|
S27 |
Bit mapped |
Unidentified |
|
S28 |
Bit mapped |
Unidentified |
|
S29 |
Flash modifier timer |
0 |
|
S31 |
Bit mapped |
Unidentified |
|
S33 |
XOFF character |
19 |
|
S40 |
Bit mapped |
Unidentified |
|
S41 |
Bit mapped |
Unidentified |
|
S80 |
Soft switch |
Unidentified |
|
S99 |
Leased line transmit level |
Unidentified |
|
S201 |
Cellular transmit level |
Unidentified |
|
S202 |
Remote escape character |
Unidentified |