MULTI-TECH SYSTEMS, INC.
AN301CX8/AN301CXB8
NIC Type |
ARCnet |
Transfer Rate |
2.5Mbps |
Data Bus |
8-bit ISA |
Topology |
Star (AN301CX8) Linear bus (AN301CXB8) |
Wiring Type |
RG-62A/U 93ohm coaxial |
Boot ROM |
Available |
NODE ADDRESS |
||||||||
Node |
SW2/1 |
SW2/2 |
SW2/3 |
SW2/4 |
SW2/5 |
SW2/6 |
SW2/7 |
SW2/8 |
0 |
- |
- |
- |
- |
- |
- |
- |
- |
1 |
Off |
On |
On |
On |
On |
On |
On |
On |
2 |
On |
Off |
On |
On |
On |
On |
On |
On |
3 |
Off |
Off |
On |
On |
On |
On |
On |
On |
4 |
On |
On |
Off |
On |
On |
On |
On |
On |
251 |
Off |
Off |
On |
Off |
Off |
Off |
Off |
Off |
252 |
On |
On |
Off |
Off |
Off |
Off |
Off |
Off |
253 |
Off |
On |
Off |
Off |
Off |
Off |
Off |
Off |
254 |
On |
Off |
Off |
Off |
Off |
Off |
Off |
Off |
255 |
Off |
Off |
Off |
Off |
Off |
Off |
Off |
Off |
Note: Node address 0 is used for messaging between nodes and must not be used. A total of 255 node address settings are available. The switches are a binary representation of the decimal node addresses. Switch 1 is the Least Significant Bit and switch 8 is the Most Significant Bit. The switches have the following decimal values: switch 1=1, 2=2, 3=4, 4=8, 5=16, 6=32, 7=64, 8=128. Turn off the switches and add the values of the off switches to obtain the correct node address. (On=0, Off=1) |
RECONFIGURATION TIMEOUT |
||||
Response Time |
Reconfig Time |
ET1 |
ET2 |
|
|
78m s |
840ms |
Open |
Open |
|
285m s |
1680ms |
Open |
Closed |
|
563m s |
1680ms |
Closed |
Open |
|
1130m s |
1680ms |
Closed |
Closed |
Note: All NICs on the network segment must have this option set the same. |
BOOT ROM |
||
Setting |
J2 |
|
|
Disabled |
Open |
|
Enabled |
Closed |
INTERRUPT REQUEST |
|||||||
IRQ |
JP3A |
JP3B |
JP3C |
JP3D |
JP3E |
JP3F |
|
|
2/9 |
Open |
Open |
Open |
Open |
Open |
Closed |
|
3 |
Open |
Open |
Open |
Open |
Closed |
Open |
|
4 |
Open |
Open |
Open |
Closed |
Open |
Open |
|
5 |
Open |
Open |
Closed |
Open |
Open |
Open |
|
6 |
Open |
Closed |
Open |
Open |
Open |
Open |
|
7 |
Closed |
Open |
Open |
Open |
Open |
Open |
BASE MEMORY ADDRESS & BOOT ROM ADDRESS |
|||||||
Base |
Boot ROM |
SW1/1 |
SW1/2 |
SW1/3 |
SW1/4 |
SW1/5 |
|
|
C0000h |
C2000h |
Off |
Off |
Off |
Off |
Off |
|
C4000h |
C6000h |
On |
Off |
Off |
Off |
Off |
|
CC000h |
CE000h |
Off |
On |
Off |
Off |
Off |
|
D0000h |
D2000h |
On |
On |
Off |
Off |
Off |
|
D4000h |
D6000h |
Off |
Off |
On |
Off |
Off |
|
D8000h |
DA000h |
On |
Off |
On |
Off |
Off |
|
DC000h |
DE000h |
Off |
On |
On |
Off |
Off |
|
E0000h |
E2000h |
On |
On |
On |
Off |
Off |
I/O BASE ADDRESS |
|||
Address |
SW1/6 |
SW1/7 |
SW1/8 |
260 - 26Fh |
On |
On |
On |
290 - 29Fh |
On |
On |
Off |
2E0 - 2EFh |
On |
Off |
On |
2F0 - 2FFh |
On |
Off |
Off |
300 - 30Fh |
Off |
On |
On |
350 - 35Fh |
Off |
On |
Off |
380 - 38Fh |
Off |
Off |
On |
3E0 - 3EFh |
Off |
Off |
Off |
DIAGNOSTIC LED(S) |
|||
LED |
Color |
Status |
Condition |
LED1 |
Green |
On |
Data is being transmitted |
LED1 |
Green |
Off |
Data is not being transmitted |
LED2 |
Red |
On |
Card is active on host data bus |
LED2 |
Red |
Off |
No card activity |