COMPEX, INC.
ANET-1A
|
NIC Type |
ARCnet |
|
Transfer Rate |
2.5Mbps |
|
Data Bus |
8-bit ISA |
|
Topology |
Star Linear Bus |
|
Wiring Type |
RG-62A/U 93ohm coaxial Unshielded twisted pair |
|
Boot ROM |
Available |
|
NODE ADDRESS | ||||||||
|
Node |
SW1/1 |
SW1/2 |
SW1/3 |
SW1/4 |
SW1/5 |
SW1/6 |
SW1/7 |
SW1/8 |
|
0 |
- |
- |
- |
- |
- |
- |
- |
- |
|
1 |
Off |
Off |
Off |
Off |
Off |
Off |
Off |
On |
|
2 |
Off |
Off |
Off |
Off |
Off |
Off |
On |
Off |
|
3 |
Off |
Off |
Off |
Off |
Off |
Off |
On |
On |
|
4 |
Off |
Off |
Off |
Off |
Off |
On |
Off |
Off |
|
251 |
On |
On |
On |
On |
On |
Off |
On |
On |
|
252 |
On |
On |
On |
On |
On |
On |
Off |
Off |
|
253 |
On |
On |
On |
On |
On |
On |
Off |
On |
|
254 |
On |
On |
On |
On |
On |
On |
On |
Off |
|
255 |
On |
On |
On |
On |
On |
On |
On |
On |
|
Note: Node address 0 is used for messaging between nodes and must not be used. A total of 255 node address settings are available. The switches are a binary representation of the decimal node addresses. Switch 8 is the Least Significant Bit and switch 1 is the Most Significant Bit. The switches have the following decimal values: switch 8=1, 7=2, 6=4, 5=8, 4=16, 3=32, 2=64, 1=128. Turn on the switches and add the values of the on switches to obtain the correct node address. (On=1, off=0) | ||||||||
|
INTERRUPT REQUEST | ||||||
|
IRQ |
JP1A |
JP1B |
JP1C |
JP1D |
JP1E | |
|
2/9 |
Closed |
Open |
Open |
Open |
Open | |
|
3 |
Open |
Closed |
Open |
Open |
Open | |
|
4 |
Open |
Open |
Closed |
Open |
Open | |
|
5 |
Open |
Open |
Open |
Closed |
Open | |
|
7 |
Open |
Open |
Open |
Open |
Closed | |
|
I/O BASE ADDRESS | ||||
|
Address |
JP2A |
JP2B |
JP2C | |
|
260h |
Closed |
Closed |
Closed | |
|
290h |
Closed |
Closed |
Open | |
|
2E0h |
Closed |
Open |
Closed | |
|
2F0h |
Closed |
Open |
Open | |
|
300h |
Open |
Closed |
Closed | |
|
350h |
Open |
Closed |
Open | |
|
380h |
Open |
Open |
Closed | |
|
3E0h |
Open |
Open |
Open | |
|
BASE MEMORY ADDRESS & BOOT ROM ADDRESS | |||||||
|
Base Address |
Boot ROM Address |
JP3A |
JP3B |
JP3C |
JP3D |
JP3E | |
|
C0000h |
C2000h |
Closed |
Closed |
Closed |
Closed |
Closed | |
|
C4000h |
C6000h |
Closed |
Closed |
Open |
Closed |
Closed | |
|
CC000h |
CE000h |
Closed |
Open |
Closed |
Closed |
Closed | |
|
D0000h |
D2000h |
Closed |
Open |
Open |
Closed |
Closed | |
|
D4000h |
D6000h |
Open |
Closed |
Closed |
Closed |
Closed | |
|
D8000h |
DA000h |
Open |
Closed |
Open |
Closed |
Closed | |
|
DC000h |
DE000h |
Open |
Open |
Closed |
Closed |
Closed | |
|
E0000h |
E2000h |
Open |
Open |
Open |
Closed |
Closed | |
|
WAIT STATE | ||
|
Setting |
JP4 | |
|
System wait states |
Open | |
|
Zero wait states |
Closed | |
|
Note:If 0 wait states is selected, I/O CHRDY must be disabled (JP5 open). | ||
|
I/O CHRDY | ||
|
Setting |
JP5 | |
|
Disabled |
Open | |
|
Enabled |
Closed | |
|
Note:If a boot ROM is installed, I/O CHRDY must be enabled (JP5 closed). If I/O CHRDY is enabled (JP5 closed), System wait states must be selected (JP4 open) | ||
|
BOOT ROM | ||
|
Setting |
JP6 | |
|
Disabled |
Open | |
|
Enabled |
Closed | |
|
CABLE TYPE | |||
|
Type |
JP7 |
JP8 | |
|
RG-58A/U 50ohm coaxial |
Pins 1 & 2 Closed |
Pins 1 & 2 Closed | |
|
Unshielded twisted pair |
PIns 2 & 3 Closed |
PIns 2 & 3 Closed | |
|
TOPOLOGY | ||
|
Topology |
JP9 | |
|
Star |
Closed | |
|
Linear Bus |
Open | |
|
DIAGNOSTIC LED(S) | |||
|
LED |
Color |
Status |
Condition |
|
LED1 |
Red |
On |
Network connection is good |
|
LED1 |
Red |
Blinking |
Network connection is broken or no activity is detected |
|
LED2 |
Green |
On |
Data is being received |
|
LED2 |
Green |
Off |
Data is not being received |
|
LED2 |
Green |
Blinking |
System power has just been applied |