IPTool.net.ua IPTools.net.ua

DE-200 for PC AT

D-LINK

DE-200 for PC AT

NIC Type

Ethernet

Transfer Rate

10Mbps

Data Bus

16-bit ISA

Topology

Linear Bus

Wiring Type

RG--58A/U 50ohm coaxial

AUI transceiver via DB-15 port

Boot ROM

Available

BOOT ROM

Setting

JP2

Disabled

Pins 1 & 2 Closed

 

Enabled

Pins 2 & 3 Closed

INTERRUPT REQUEST

IRQ

JP3a

JP3B

JP3C

JP3D

JP3E

JP3F

JP3G

JP3H

JP3I

JP3J

JP3K

3

Closed

Open

Open

Open

Open

Open

Open

Open

Open

Open

Open

4

Open

Closed

Open

Open

Open

Open

Open

Open

Open

Open

Open

5

Open

Open

Closed

Open

Open

Open

Open

Open

Open

Open

Open

6

Open

Open

Open

Closed

Open

Open

Open

Open

Open

Open

Open

7

Open

Open

Open

Open

Closed

Open

Open

Open

Open

Open

Open

9

Open

Open

Open

Open

Open

Closed

Open

Open

Open

Open

Open

10

Open

Open

Open

Open

Open

Open

Closed

Open

Open

Open

Open

11

Open

Open

Open

Open

Open

Open

Open

Closed

Open

Open

Open

12

Open

Open

Open

Open

Open

Open

Open

Open

Closed

Open

Open

14

Open

Open

Open

Open

Open

Open

Open

Open

Open

Closed

Open

15

Open

Open

Open

Open

Open

Open

Open

Open

Open

Open

Closed

I/O BASE ADDRESS

Address

JP6A

JP6B

JP6C

 

200h

Pins 1 & 2 Closed

Pins 1 & 2 Closed

Pins 1 & 2 Closed

 

220h

Pins 2 & 3 Closed

Pins 1 & 2 Closed

Pins 1 & 2 Closed

 

240h

Pins 1 & 2 Closed

Pins 1 & 2 Closed

Pins 2 & 3 Closed

 

260h

Pins 2 & 3 Closed

Pins 1 & 2 Closed

Pins 2 & 3 Closed

300h

Pins 1 & 2 Closed

Pins 2 & 3 Closed

Pins 1 & 2 Closed

 

320h

Pins 2 & 3 Closed

Pins 2 & 3 Closed

Pins 1 & 2 Closed

 

340h

Pins 1 & 2 Closed

Pins 2 & 3 Closed

Pins 2 & 3 Closed

 

360h

Pins 2 & 3 Closed

Pins 2 & 3 Closed

Pins 2 & 3 Closed

CHIP SET

Type

JP4

Standard

Pins 1 & 2 Closed

 

Non-standard 1

Pins 2 & 3 Closed

 

Non-standard 2

Pins 3 & 4 closed

Note:Non-standard PC AT systems and early versions of Chips & Technologies chipsets do not use timing compatible with the IBM AT bus for the I/O CHRDY signal. If the NIC does not work with the standard setting, try one of the two non-standard settings.

CABLE TYPE

Type

JP1A-G

RG-58A/U 50ohm coaxial

Pins 2 & 3 Closed

 

AUI transceiver via DB-15 port

Pins 1 & 2 Closed

BOOT ROM ADDRESS

Address

JP5A

JP5B

JP5C

 

C8000h

Pins 1 & 2 Closed

Pins 2 & 3 Closed

Pins 1 & 2 Closed

 

CC000h

Pins 2 & 3 Closed

Pins 2 & 3 Closed

Pins 1 & 2 Closed

D0000h

Pins 1 & 2 Closed

Pins 1 & 2 Closed

Pins 2 & 3 Closed

 

D4000h

Pins 2 & 3 Closed

Pins 1 & 2 Closed

Pins 2 & 3 Closed

 

D8000h

Pins 1 & 2 Closed

Pins 2 & 3 Closed

Pins 2 & 3 Closed

 

DC000h

Pins 2 & 3 Closed

Pins 2 & 3 Closed

Pins 2 & 3 Closed