TEKNOR INDUSTRIAL COMPUTERS, INC.
PCI-935
|
Device Type |
Single board computer |
|
Processor |
Pentium |
|
Processor Speed |
75/90/100/120/133/150/166/200MHz |
|
Chip Set |
VIA Apollo |
|
Video Chip Set |
Cirrus Logic |
|
Maximum Onboard Memory |
128MB (EDO supported) |
|
Maximum Video Memory |
4MB |
|
Cache |
512KB |
|
BIOS |
AMI |
|
Dimensions |
338mm x 122mm |
|
I/O Options |
Ethernet 10Base2 connector, Ethernet 10BaseT connector, floppy drive interface, IDE interfaces (2), SCSI interface, parallel port, PS/2 mouse interface, serial ports (2), VGA feature connector, VGA port |
|
CONNECTIONS | |||
|
Purpose |
Location |
Purpose |
Location |
|
Chassis fan power |
J1 |
Flat panel connector |
J9 |
|
SCSI interface |
J2 |
Parallel port |
J10 |
|
IDE interface 1 |
J3 |
VGA feature connector |
J11 |
|
Floppy drive interface |
J4 |
PS/2 mouse interface |
J12 |
|
Front panel connector |
J5 |
VGA port |
J14 |
|
Serial port 1 |
J6 |
Ethernet 10BaseT connector |
J17 |
|
Serial port 2 |
J7 |
Ethernet 10Base2 connector |
J21 |
|
IDE interface 2 |
J8 | ||
|
USER CONFIGURABLE SETTINGS | |||
|
Function |
Label |
Position | |
|
|
BIOS boot select normal |
J13 |
Open |
|
BIOS boot select emergancy boot |
J13 |
Closed | |
|
|
Factory configured do not alter |
J25 |
Unidentified |
|
|
Factory configured do not alter |
J26 |
Unidentified |
|
|
Factory configured do not alter |
J27 |
Unidentified |
|
|
Serial mode select normal |
W8/pins 1 & 2 |
Open |
|
Serial mode select download |
W8/pins 1 & 2 |
Closed | |
|
|
Standard mode |
W8/pins 3 & 4 |
Open |
|
VT100 mode |
W8/pins 3 & 4 |
Closed | |
|
|
Teknor extension enabled |
W8/pins 5 & 6 |
Open |
|
Teknor extension disabled |
W8/pins 5 & 6 |
Closed | |
|
|
On board video enabled |
W8/pins 7 & 8 |
Open |
|
On board video disabled |
W8/pins 7 & 8 |
Closed | |
|
|
Cache type select write back |
W11 |
Pins 1 & 2 closed |
|
Cache type select write through |
W11 |
Pins 2 & 3 closed | |
|
|
Non maskable interrupt on power fail output disabled |
W13 |
Open |
|
Non maskable interrupt on power fail output enabled |
W13 |
Closed | |
|
|
Watchdog timer enabled |
W23 |
Closed |
|
Watchdog timer disabled |
W23 |
Open | |
|
|
Internal battery disabled |
W24 |
Open |
|
Internal battery enabled |
W24 |
Closed | |
|
SIMM CONFIGURATION | ||
|
Size |
Bank 0 |
Bank 1 |
|
8MB |
(2) 1M x 36 |
None |
|
16MB |
(2) 2M x 36 |
None |
|
16MB |
(2) 1M x 36 |
(2) 1M x 36 |
|
24MB |
(2) 2M x 36 |
(2) 1M x 36 |
|
32MB |
(2) 4M x 36 |
None |
|
32MB |
(2) 2M x 36 |
(2) 2M x 36 |
|
40MB |
(2) 4M x 36 |
(2) 1M x 36 |
|
SIMM CONFIGURATION (CONT) | ||
|
Size |
Bank 0 |
Bank 1 |
|
48MB |
(2) 4M x 36 |
(2) 2M x 36 |
|
64MB |
(2) 8M x 36 |
None |
|
64MB |
(2) 4M x 36 |
(2) 4M x 36 |
|
72MB |
(2) 8M x 36 |
(2) 1M x 36 |
|
80MB |
(2) 8M x 36 |
(2) 2M x 36 |
|
96MB |
(2) 8M x 36 |
(2) 4M x 36 |
|
128MB |
(2) 8M x 36 |
(2) 8M x 36 |
|
Note: Board accepts EDO memory. | ||
|
CACHE CONFIGURATION |
|
Note: The location of the cache is unidentified. |
|
VIDEO MEMORY CONFIGURATION |
|
Note: The location of the video memory is unidentified. |
|
CPU SPEED SELECTION | |||||||
|
CPU speed |
Clock speed |
Multiplier |
W5 |
W6 |
W7 |
W21 |
W31 |
|
75MHz |
50MHz |
1.5x |
1 & 2 |
2 & 3 |
2 & 3 |
1 & 2 |
1 & 2 |
|
90MHz |
60MHz |
1.5x |
1 & 2 |
1 & 2 |
1 & 2 |
1 & 2 |
1 & 2 |
|
100MHz |
66MHz |
1.5x |
2 & 3 |
1 & 2 |
2 & 3 |
1 & 2 |
1 & 2 |
|
120MHz |
60MHz |
2x |
1 & 2 |
1 & 2 |
1 & 2 |
1 & 2 |
2 & 3 |
|
133MHz |
66MHz |
2x |
2 & 3 |
1 & 2 |
2 & 3 |
1 & 2 |
2 & 3 |
|
150MHz |
60MHz |
2.5x |
1 & 2 |
1 & 2 |
1 & 2 |
2 & 3 |
2 & 3 |
|
166MHz |
66MHz |
2.5x |
2 & 3 |
1 & 2 |
2 & 3 |
2 & 3 |
2 & 3 |
|
200MHz |
66MHz |
3x |
2 & 3 |
1 & 2 |
2 & 3 |
2 & 3 |
1 & 2 |
|
Note: Pins designated should be in the closed position. | |||||||
|
SERIAL PORT 2 SELECTION | ||||||
|
Setting |
W14 |
W17 |
W18 |
W19 |
W20 | |
|
RS-232 |
Open |
1 & 2 |
1 & 2 |
1 & 2 |
1 & 2 | |
|
RS-422 |
Closed |
2 & 3 |
2 & 3 |
2 & 3 |
2 & 3 | |
|
RS-485 |
Closed |
2 & 3 |
2 & 3 |
2 & 3 |
2 & 3 | |
|
Note: Pins designated should be in the closed position. | ||||||
|
SERIAL PORT 2 LOOPBACK SELECTION | |||
|
Setting |
W15 |
W16 | |
|
Normal |
Open |
Open | |
|
Loopback |
Closed |
Closed | |
|
BASE I/O ADDRESS SELECTION | ||
|
Address |
W9 | |
|
190H |
Pins 1 & 2, 3 & 4 closed | |
|
290H |
Pins 1 & 2 closed | |
|
390H |
Pins 3 & 4 closed | |
|
490H |
Open | |
|
SCSI TERMINATION SELECTION | ||
|
Setting |
W4 | |
|
Controlled by hardware |
Pins 2 & 3 closed | |
|
Controlled by software |
Pins 1 & 2 closed | |
|
Disabled by hardware |
Open | |
|
EDOUT SELECTION | ||
|
Setting |
W21 | |
|
Left to software |
Open | |
|
EDOUT to pin 29 on J4 |
Pins 1 & 3 closed | |
|
EDOUT to ground pin 17 on J4 |
Pins 2 & 4 closed | |
|
EDOUT to pin 17 on J4 |
Pins 1 & 2 closed | |
|
EDOUT to ground pin 29 on J4 |
Pins 3 & 4 closed | |
|
HDOUT SELECTION | ||
|
Setting |
W22 | |
|
Left to software |
Open | |
|
HDOUT to pin 33 on J4 |
Pins 1 & 3 closed | |
|
HDOUT to ground pin 27 on J4 |
Pins 2 & 4 closed | |
|
HDOUT to pin 27 on J4 |
Pins 1 & 2 closed | |
|
HDOUT to ground pin 33 on J4 |
Pins 3 & 4 closed | |