NIAGARA SMD TECHNOLOGY, INC.
NT928SPP
Processor |
Pentium Pro |
Processor Speed |
150/166/180/200/210/233/240/266/270/300MHz |
Chip Set |
Intel |
Video Chip Set |
None |
Maximum Onboard Memory |
512MB (EDO supported) |
Maximum Video Memory |
None |
Cache |
256/512KB (located on Pentium Pro CPU) |
BIOS |
AMI/Award/Phoenix |
Dimensions |
305mm x 244mm |
I/O Options |
32-bit PCI slots (4), floppy drive interface, green PC connector, IDE interfaces (2), Ultra-SCSI Wide interface, SCSI interface, parallel port, PS/2 mouse port, serial ports (2), ATX power connector, USB connector, IR connector |
NPU Options |
None |
CONNECTIONS | |||
Purpose |
Location |
Purpose |
Location |
ATX power connector |
ATX |
Speaker |
J31 pins 1 - 4 |
Serial port |
CN1 |
Power LED & keylock |
J31 pins 6 - 10 |
Parallel port |
CN2 |
Reset switch |
J31 pins 11 & 12 |
PS/2 mouse port |
CN3 |
SCSI LED |
J31 pins 13 & 14 |
Serial port |
CN4 |
IDE interface LED |
J31 pins 15 & 16 |
Floppy drive interface |
CN5 |
Green PC connector |
J31 pins 17 & 18 |
IDE interface |
CN6 |
Turbo LED |
J31 pins 19 & 20 |
IDE interface |
CN7 |
Power on/off switch |
JP7 |
SCSI interface |
CN8 |
Remote power switch |
JP8 |
Ultra-SCSI Wide interface |
CN9 |
32-bit PCI slots |
PC1 PC4 |
Note: The location of the IR &USB connectors are unidentified. |
USER CONFIGURABLE SETTINGS | |||
Function |
Label |
Position | |
|
Factory configured - do not alter |
J32 |
Unidentified |
Wide SCSI enabled |
J33 |
Closed | |
Wide SCSI disabled |
J33 |
Open | |
|
Auto power enabled |
JP5 |
Closed |
Auto power disabled |
JP5 |
Open | |
|
Factory configured - do not alter |
JP6 |
Unidentified |
SCSI chip enabled |
JP11 |
Pins 1 & 2 closed | |
SCSI chip disabled |
JP11 |
Pins 2 & 3 closed | |
|
Factory configured - do not alter |
JP14 |
Unidentified |
|
Factory configured - do not alter |
JP15 |
Unidentified |
DRAM CONFIGURATION | ||
Size |
Bank 0 |
Bank 1 |
8MB |
(2) 1M x 36 |
None |
16MB |
(2) 2M x 36 |
None |
16MB |
(2) 1M x 36 |
(2) 1M x 36 |
24MB |
(2) 2M x 36 |
(2) 1M x 36 |
32MB |
(2) 4M x 36 |
None |
32MB |
(2) 2M x 36 |
(2) 2M x 36 |
40MB |
(2) 4M x 36 |
(2) 1M x 36 |
48MB |
(2) 4M x 36 |
(2) 2M x 36 |
64MB |
(2) 8M x 36 |
None |
64MB |
(2) 4M x 36 |
(2) 4M x 36 |
72MB |
(2) 8M x 36 |
(2) 1M x 36 |
80MB |
(2) 8M x 36 |
(2) 2M x 36 |
96MB |
(2) 8M x 36 |
(2) 4M x 36 |
128MB |
(2) 8M x 36 |
(2) 8M x 36 |
128MB |
(2) 16M x 36 |
None |
136MB |
(2) 16M x 36 |
(2) 1M x 36 |
144MB |
(2) 16M x 36 |
(2) 2M x 36 |
DRAM CONFIGURATION (CONT) | ||
Size |
Bank 0 |
Bank 1 |
160MB |
(2) 16M x 36 |
(2) 4M x 36 |
192MB |
(2) 16M x 36 |
(2) 8M x 36 |
256MB |
(2) 32M x 36 |
None |
256MB |
(2) 16M x 36 |
(2) 16M x 36 |
264MB |
(2) 32M x 36 |
(2) 1M x 36 |
272MB |
(2) 32M x 36 |
(2) 2M x 36 |
288MB |
(2) 32M x 36 |
(2) 4M x 36 |
320MB |
(2) 32M x 36 |
(2) 8M x 36 |
384MB |
(2) 32M x 36 |
(2) 16M x 36 |
512MB |
(2) 32M x 36 |
(2) 32M x 36 |
Note: Board accepts EDO memory. Board also accepts x 32 SIMMs. The location of banks 0 & 1 are unidentified. |
CACHE CONFIGURATION |
Note: 256KB/512KB cache is located on the Pentium Pro CPU. |
CPU SPEED SELECTION | |
Speed |
JP17 |
150MHz |
Pins 1 & 2 closed |
166MHz |
Pins 3 & 4 closed |
180MHz |
Pins 5 & 6 closed |
200MHz |
Pins 7 & 8 closed |
210MHz |
Pins 9 & 10 closed |
233MHz |
Pins 11 & 12 closed |
240MHz |
Pins 13 & 14 closed |
266MHz |
Pins 15 & 16 closed |
270MHz |
Pins 17 & 18 closed |
300MHz |
Pins 19 & 20 closed |
VOLTAGE SOURCE SELECTION | |
Setting |
JP1 |
3.3v from on board regulator |
Pins 3 & 5, 4 & 6 closed |
3.3v from ATX power supply |
Pins 1 & 3, 2 & 4 closed |
SCSI TERMINATION SELECTION (LOW) | ||
Setting |
JP16 | |
Low byte controlled by BIOS |
Pins 2 & 3 closed | |
Low byte terminator on |
Pins 1 & 2 closed | |
Low byte terminator off |
Open |
SCSI TERMINATION SELECTION (HIGH) | ||
Setting |
JP18 | |
High byte terminator on |
Pins 1 & 2 closed | |
High byte terminator off |
Open | |
High byte controlled by BIOS |
Pins 2 & 3 closed |