LANNER ELECTRONICS, INC.
AP-5200IH
|
Device Type |
Mainboard |
|
Processor |
CX 6X86/Pentium |
|
Processor Speed |
75/90/100/120/133/150/166/180/200MHz |
|
Chip Set |
Intel |
|
Video Chip Set |
Unidentified |
|
Maximum Onboard Memory |
64MB (EDO & SDRAM supported) |
|
Maximum Video Memory |
1MB |
|
Cache |
256/512KB |
|
BIOS |
Award |
|
Dimensions |
185mm x 122mm |
|
I/O Options |
Floppy drive interface, green PC connector, IDE interfaces (2), parallel port, PS/2 mouse port, serial ports (2), cache slot, IR connector, USB connectors (2), VGA interface, PCI piggyback connector |
|
NPU Options |
None |
|
CONNECTIONS | |||
|
Purpose |
Location |
Purpose |
Location |
|
Serial port 1 |
CN1 |
Power LED & keylock |
J1 |
|
PS/2 mouse port |
CN2 |
Speaker |
J2 |
|
Serial port 2 |
CN3 |
IDE interface LED |
J3 |
|
IDE interface 1 |
CN4 |
Turbo LED |
J4 |
|
IDE interface 2 |
CN5 |
Reset switch |
J5 |
|
Parallel port |
CN6 |
Green PC connector |
JP10 |
|
USB connector 1 |
CN7 |
Auxiliary keyboard connector |
KCN1 |
|
USB connector 2 |
CN8 |
PCI piggyback connector |
PC1 |
|
VGA interface |
CN9 |
PCI piggyback connector |
PC2 |
|
IR connector |
IR1 |
Cache slot |
SL1 |
|
USER CONFIGURABLE SETTINGS | |||
|
Function |
Label |
Position | |
|
|
Factory configured - do not alter |
JP5 |
Open |
|
|
Factory configured - do not alter |
JP6 |
Open |
|
|
CMOS memory normal operation |
JP7 |
Open |
|
CMOS memory clear |
JP7 |
Closed | |
|
Power good signal detect from power supply |
JP11 |
Pins 2 & 3 closed | |
|
Power good signal detect from board |
JP11 |
Pins 1 & 2 closed | |
|
Flash BIOS voltage select 12v |
JP12 |
Pins 2 & 3 closed | |
|
Flash BIOS voltage select 5v |
JP12 |
Pins 1 & 2 closed | |
|
SIMM CONFIGURATION | |
|
Size |
Bank 0 |
|
8MB |
(2) 1M x 36 |
|
16MB |
(2) 2M x 36 |
|
32MB |
(2) 4M x 36 |
|
64MB |
(2) 8M x 36 |
|
CACHE CONFIGURATION | |
|
Size |
SL1 |
|
256KB |
256KB module installed |
|
512KB |
512KB module installed |
|
VIDEO MEMORY CONFIGURATION |
|
Note: The size & location of the video memory is unidentified. |
|
CPU SPEED SELECTION (CYRIX) | |||||
|
CPU speed |
Clock speed |
Multiplier |
JP2 |
JP3 |
JP4 |
|
120MHz |
60MHz |
2x |
Open |
Closed |
1 & 2 |
|
133MHz |
66MHz |
2x |
Open |
Closed |
Open |
|
150MHz |
60MHz |
2x |
Open |
Closed |
1 & 2 |
|
166MHz |
66MHz |
2x |
Open |
Closed |
Open |
|
Note: Pins designated should be in the closed position. | |||||
|
CPU SPEED SELECTION (INTEL) | |||||
|
CPU speed |
Clock speed |
Multiplier |
JP2 |
JP3 |
JP4 |
|
75MHz |
50MHz |
1.5x |
Open |
Open |
3 & 4 |
|
90MHz |
60MHz |
1.5x |
Open |
Open |
1 & 2 |
|
100MHz |
66MHz |
1.5x |
Open |
Open |
Open |
|
120MHz |
60MHz |
2x |
Open |
Closed |
1 & 2 |
|
133MHz |
66MHz |
2x |
Open |
Closed |
Open |
|
150MHz |
60MHz |
2.5x |
Closed |
Closed |
1 & 2 |
|
166MHz |
66MHz |
2.5x |
Closed |
Closed |
Open |
|
180MHz |
60MHz |
3x |
Closed |
Open |
1 & 2 |
|
200MHz |
66MHz |
3x |
Closed |
Open |
Open |
|
Note: Pins designated should be in the closed position. | |||||
|
CPU VOLTAGE SELECTION | |
|
Voltage |
JP1 |
|
3.3v |
Pins 1 & 2 closed |
|
3.5v |
Pins 2 & 3 closed |
|
WATCHDOG TIMER ACTIVE SELECTION | ||
|
Time out |
JP8 | |
|
.5 sec |
Pins 2 & 3 closed | |
|
1 sec |
Pins 5 & 6 closed | |
|
2 sec |
Pins 8 & 9 closed | |
|
4 sec |
Pins 11 & 12 closed | |
|
8 sec |
Pins 10 & 11 closed | |
|
16 sec |
Pins 7 & 8 closed | |
|
32 sec |
Pins 4 & 5 closed | |
|
64 sec |
Pins 1 & 2 closed | |
|
WATCHDOG TIMER ACTIVE SELECTION | ||
|
Setting |
JP9 | |
|
Reset system |
Pins 1 & 2 closed | |
|
NMI system |
Pins 2 & 3 closed | |
|
Disabled |
Open | |