IPC CORPORATION, LTD.
IPC MBMPS328#11
|
Processor |
80386SX (exact location unidentified) |
|
Processor Speed |
25/33MHz |
|
Chip Set |
Unidentified |
|
Max. Onboard DRAM |
9MB |
|
Cache |
8/32KB |
|
BIOS |
Unidentified |
|
Dimensions |
355mm x 305mm |
|
I/O Options |
Scanner port, IFM328PNL connectors (2), serial ports (2), floppy drive interface, IDE interfaces (2), SCSI connector, parallel port, customer display connector, printer power supply connector, drawer connector, hard drive power connector, riser slot |
|
NPU Options |
None |
|
CONNECTIONS | |||
|
Purpose |
Location |
Purpose |
Location |
|
Scanner port |
J1 |
SCSI connector |
J11 |
|
IFM328PNL connector |
J2 |
2.5" IDE interface |
J12 |
|
Serial port 1 |
J3 |
3.5 " IDE interface |
J13 |
|
IFM328PNL connector |
J5 |
Printer power supply connector |
JP2 |
|
Serial port 2/external floppy |
J6 |
Reset switch |
JP1 |
|
Customer display connector |
J7 |
Drawer connector |
JP18 |
|
Speaker |
J9 |
Hard drive power connector |
JP23 |
|
Parallel port |
J10 |
Riser slot |
SL1 |
|
USER CONFIGURABLE SETTINGS | |||
|
Function |
Jumper |
Position | |
|
|
Read ROM scan code enabled |
J4-1 |
Open |
|
Read program scan mode enabled |
J4-1 |
Closed | |
|
|
MCR mode select independent |
J4-2 |
Open |
|
MCR mode select simultaneous |
J4-2 |
Closed | |
|
|
Reset disabled |
JP1 |
Open |
|
Reset enabled |
JP1 |
Closed | |
|
|
Keyboard buzzer enabled |
JP3 |
Closed |
|
Keyboard buzzer disabled |
JP3 |
Open | |
|
|
Operator display address select 100H |
JP4 |
pins 1 & 2 closed |
|
Operator display address select 10CH |
JP4 |
pins 2 & 3 closed | |
|
|
Floppy drive set as A drive |
JP7 |
Closed |
|
Floppy drive set as B drive |
JP7 |
Open | |
|
|
COM1 signal select RI signal |
JP8 |
pins 1 & 2 closed |
|
COM1 signal select +5v |
JP8 |
pins 2 & 3 closed | |
|
|
ROM type select external |
JP9 |
Closed |
|
ROM type select internal |
JP9 |
Open | |
|
|
Keylock #5 to control read NVR disabled |
JP10 |
pins 1 & 2 closed |
|
Keylock #5 to control read NVR enabled |
JP10 |
pins 2 & 3 closed | |
|
|
SRAM for keyboard controller size select 2KB |
JP11 |
pins 1 & 2 closed |
|
SRAM for keyboard controller size select 8KB |
JP11 |
pins 2 & 3 closed | |
|
|
NVR type select 128KB |
JP12 |
Open |
|
NVR type select 256KB |
JP12 |
pins 1 & 2 closed | |
|
NVR type select 8/32KB |
JP12 |
pins 2 & 3 closed | |
|
|
Keylock #1 to control write NVR disabled |
JP13 |
pins 1 & 2 closed |
|
Keylock #1 to control write NVR enabled |
JP13 |
pins 2 & 3 closed | |
|
|
CMOS memory clear 1287A only |
JP15 |
pins 1 & 2 closed |
|
CMOS memory clear 1287 only |
JP15 |
pins 2 & 3 closed | |
|
|
Monitor type select monochrome |
JP16 |
Open |
|
Monitor type select CGA/EGA/VGA |
JP16 |
Closed | |
|
|
IDE interface disabled |
JP17 |
Open |
|
IDE interface enabled |
JP17 |
Closed | |
|
|
Serial port select COM1 & COM2 |
JP19 |
pins 1 & 2 closed |
|
Serial port select COM3 & COM4 |
JP19 |
pins 2 & 3 closed | |
|
USER CONFIGURABLE SETTINGS (CONT) | |||
|
Function |
Jumper |
Position | |
|
|
Keylock #1 control of floppy access disabled |
JP21 |
pins 1 & 2 closed |
|
Keylock #1 control of floppy access enabled |
JP21 |
pins 2 & 3 closed | |
|
|
Hard drive type select 3.5" |
JP22 |
pins 1 & 2 closed |
|
Hard drive type select 2.5" |
JP22 |
pins 2 & 3 closed | |
|
|
Buzzer enabled |
JP24 |
pins 2 & 3 closed |
|
Speaker enabled |
JP24 |
pins 1 & 2 closed | |
|
Note: The location of J4 is unidentified. | |||
|
DRAM CONFIGURATION | |||
|
Size |
Bank 0 |
Bank 1 |
Bank 2 |
|
512KB |
512KB |
NONE |
NONE |
|
1MB |
512KB |
(1) 256K x 16 |
NONE |
|
1.5MB |
512KB |
(1) 256K x 16 |
(2) 256K x 9 |
|
3MB |
512KB |
(1) 256K x 16 |
(2) 1M x 9 |
|
9MB |
512KB |
(1) 256K x 16 |
(2) 4M x 9 |
|
Note: Bank 0 is factory installed and is not configurable. The location of Banks 0 & 1 are unidentified. Bank 1 uses a proprietary SIMM module. | |||
|
CACHE CONFIGURATION |
|
Note: The location and the cache chip sizes are unidentified. Cache installed will either be 8KB or 32KB. |
|
CACHE JUMPER CONFIGURATION | ||
|
Size |
JP5 |
JP6 |
|
8KB |
pins 2 & 3 closed |
pins 1 & 2 closed |
|
32KB |
pins 1 & 2 closed |
pins 2 & 3 closed |
|
CPU SPEED CONFIGURATION | |
|
Speed |
JP14 |
|
25MHz |
pins 1 & 2 closed |
|
33MHz |
pins 2 & 3 closed |
|
MAGNETIC CARD READER CONFIGURATION | |||
|
MCR |
J4-3 |
J4-4 | |
|
Single track |
Closed |
Closed | |
|
Dual track |
Open |
Closed | |
|
Triple track |
Closed |
Open | |
|
Note: The location of J4 is unidentified. | |||
|
CCD SCANNER BAUD RATE CONFIGURATION | ||||
|
Baud rate |
J4-5 |
J4-6 |
J4-7 | |
|
1200 BPS |
Closed |
Closed |
Closed | |
|
2400 BPS |
Open |
Closed |
Closed | |
|
4800 BPS |
Closed |
Open |
Closed | |
|
9600 BPS |
Closed |
Closed |
Open | |
|
Note: The location of J4 is unidentified. | ||||