QUATECH, INC.
RW-100T
|
Card Type |
I/O controller |
|
Chipset/Controller |
Unidentified UART |
|
I/O Options |
Serial ports (2) |
|
Maximum DRAM |
N/A |
|
CONNECTIONS | |||
|
Purpose |
Location |
Purpose |
Location |
|
Serial port 1 |
CN1 |
Serial port 2 |
CN2 |
|
CLOCK SPEED SELECT | ||
|
Speed |
J1 | |
|
18.432 |
Pins 2 & 5 closed | |
|
9.216 |
Pins 1 & 2, 5 & 6 closed | |
|
3.6864 |
Pins 2 & 3, 4 & 5 closed | |
|
1.8432 |
Pins 1 & 2, 3 & 6, 4 & 5 closed | |
|
PRIMARY PORT I/O ADDRESS SELECT | |||
|
Address |
SW1 |
SW3 | |
|
03F8h |
1 & 2, 3 & 4, 5 & 6 on |
6 on | |
|
03E8h |
1 & 2, 3 & 4, 5 & 6 on |
4 & 6 on | |
|
3220h |
1 & 2, 5 & 6, 8 on |
1 & 2, 4 & 5, 6 on | |
|
Note:The address range for the RW-100T is from 0 to FFFFh. The switches are a binary representation of the addresses. The switches have the following decimal values: SW1/1=8, SW1/2=4, SW1/3=2, SW1/4=1, SW1/5=8, SW1/6=4, SW1/7=2, SW1/8=1, SW3/1=8, SW3/2=4, SW3/3=2, SW3/4=1, SW3/5=8. | |||
|
SECONDARY PORT I/O ADDRESS SELECT | |||
|
Address |
SW2 |
SW4 | |
|
02F8h |
1 & 2, 3 & 4, 5 &6, 8 on |
6 on | |
|
02E8h |
1 & 2, 3 & 4, 5 & 6, 8 on |
4 & 6 on | |
|
5228h |
1 & 3, 5 & 6, 8 on |
1 & 2, 4 & 6 on | |
|
Note:The address range for the RW-100T is from 0 to FFFFh. The switches are a binary representations of the addresses. The switches have the following decimal values: SW2/1=8, SW2/2=4, SW2/3=2, SW2/4=1, SW2/5=8, SW2/6=4, SW2/7=2, SW2/8=1, SW4/1=8, SW4/2=4, SW4/3=2, SW4/4=1, SW4/5=8. | |||
|
INTERRUPT SELECT | ||
|
IRQ |
J3 (Port 1) |
J4 (Port 2) |
|
IRQ2 |
Pins 1 & 12 closed |
Pins 1 & 12 closed |
|
IRQ3 |
Pins 2 & 13 closed |
Pins 2 & 13 closed |
|
IRQ4 |
Pins 3 & 14 closed |
Pins 3 & 14 closed |
|
IRQ5 |
Pins 4 & 15 closed |
Pins 4 & 15 closed |
|
IRQ6 |
Pins 5 & 16 closed |
Pins 5 & 16 closed |
|
IRQ7 |
Pins 6 & 17 closed |
Pins 6 & 17 closed |
|
IRQ10 |
Pins 7 & 18 closed |
Pins 7 & 18 closed |
|
IRQ11 |
Pins 8 & 19 closed |
Pins 8 & 19 closed |
|
IRQ12 |
Pins 9 & 20 closed |
Pins 9 & 20 closed |
|
IRQ14 |
Pins 10 & 21 closed |
Pins 10 & 21 closed |
|
IRQ15 |
Pins 11 & 22 closed |
Pins 11 & 22 closed |
|
SECONDARY SERIAL PORT OUTPUT CONFIGURATION | |
|
Output |
Protocol Selectors Installed |
|
RS-232C DTE |
SB1 & SB4 |
|
RS-232C DCE |
SB1 & SB5 |
|
RS-485 |
SB2 & SB3 |
|
Note:These settings are valid only when no protocol selectors are installed on any jumpers other than those indicated. Incorrect combinations of these selectors may result in card or system damage. | |
|
PRIMARY SERIAL PORT DTE/DCE CONFIGURATION |
|
Serial Port CN1 |
|
Jumper J6
|
|
SECONDARY SERIAL PORT DTE/DCE CONFIGURATION |
|
Serial Port CN2 |
|
Jumpers SB1 - SB5
|
|
AUXILIARY I/O CONFIGURATION | |
|
Function |
J5 |
|
RTS/CTS loopback |
Pins 3 & 6 closed |
|
Transmit RTS |
Pins 2 & 3 closed |
|
Receive CTS |
Pins 5 & 6 closed |
|
RCLK/XCLK loopback |
Pins 1 & 4 closed |
|
Transmit XCLK |
Pins 1 & 2 closed |
|
Receive RCLK |
Pins 4 & 5 closed |
|
AUX out/AUX in loopback |
Pins 2 & 5 closed |
|
Note: The default setting for J5 is to have Pins 1 & 4, 2 & 5, and 3 & 6 closed. | |
|
HARDWARE OPTION SWITCH CONFIGURATION | |
|
Setting |
J2 |
|
SW5 enabled for hardware option select for Port 1 |
Pins 1 & 5 closed |
|
SW6 enabled for hardware option select for Port 2 |
Pins 2 & 5 closed |
|
TRI-STATE OUTPUT CONFIGURATION | |
|
Setting |
J2 |
|
Tri-state enabled for Port 1 |
Pins 3 & 7 closed |
|
Tri-state enabled for Port 2 |
Pins 4 & 8 closed |
|
USER DEFINABLE HARDWARE OPTION CONFIGURATION | ||
|
Address |
SW5 |
SW6 |
|
6Ah |
2 & 3, 5 &7 on |
2 & 3, 5 &7 on |
|
B4h |
1 & 3, 4 & 6 on |
1 & 3, 4 & 6 on |
|
Note:These switches are a binary representation of the addresses. The switches have the following decimal values: switch 1=8, switch 2=4, switch 3=2, switch 4=1, switch 5=8, switch 6=4, switch 7=2, switch 8=1. | ||