QUATECH, INC.
MPI-600
|
Card Type |
I/O controller |
|
Chipset/Controller |
Intel 80C188 |
|
I/O Options |
Serial ports (2) |
|
Maximum DRAM |
N/A |
|
CONNECTIONS | |||
|
Purpose |
Location |
Purpose |
Location |
|
Serial port 1 |
CN1 |
SCC channel "B" connector |
J2 |
|
Serial port 2 |
CN2 | ||
|
I/O ADDRESS SELECT | ||||||||
|
Address |
SW1/1 |
SW1/2 |
SW1/3 |
SW1/4 |
SW1/5 |
SW1/6 |
SW1/7 |
SW1/8 |
|
3F8h |
On |
Off |
Off |
Off |
Off |
Off |
Off |
Off |
|
3E8h |
On |
Off |
Off |
Off |
Off |
Off |
On |
Off |
|
2F8h |
On |
Off |
On |
Off |
Off |
Off |
Off |
Off |
|
2E8h |
On |
Off |
On |
Off |
Off |
Off |
On |
Off |
|
7F8h |
Off |
Off |
Off |
Off |
Off |
Off |
Off |
Off |
|
Note:The address range for the MPI-600 can be set between 000h and 7F8h. The switches are a binary representation of the addresses. The switches have the following decimal values: switch 1=4, switch 2=2, switch 3=1, switch 4=8, switch 5=4, switch 6=2, switch 7=1, switch 8=8. Turn Off the switches and add the values of the Off switches to obtain the correct address. | ||||||||
|
DMA CHANNEL SELECT | ||
|
DMA |
J3 |
J4 |
|
1 |
Pins 1 & 3 closed |
Pins 1 & 3 closed |
|
3 |
Pins 2 & 4 closed |
Pins 2 & 4 closed |
|
None |
All open |
All open |
|
PARALLEL PORT CONFIGURATION | |
|
J1 |
Designation |
|
Pins 1 - 4 |
Connected to ground |
|
Pin 5 |
Connected to 8256 pin P27 |
|
Pin 6 |
Connected to 8256 Pin P26 |
|
Pin 7 |
Connected to 8256 Pin P25 |
|
Pin 8 |
Connected to 8256 Pin P24 |
|
INTERRUPT SELECT | |
|
IRQ |
J5 |
|
IRQ2 |
Pins 1 & 7 closed |
|
IRQ3 |
Pins 2 & 8 closed |
|
IRQ4 |
Pins 3 & 9 closed |
|
IRQ5 |
Pins 4 & 10 closed |
|
IRQ6 |
Pins 5 & 11 closed |
|
IRQ7 |
Pins 6 & 12 closed |
|
CURRENT LOOP POWER LEVEL SELECT | ||
|
Setting |
J6 |
J7 |
|
+12 volts |
Open |
Closed |
|
-12 volts |
Closed |
Open |
|
External power source used |
Open |
Open |
|
SIGNAL CONFIGURATION | |||||
|
Signal Type |
Mode |
J8 |
J9 |
J10 |
J11 |
|
RTxC/RRxC |
V.35 (RS-422) |
1 & 3 closed |
1 & 3 closed |
N/A |
N/A |
|
RTxC/RRxC |
V.24 (RS-232) |
2 & 4 closed |
2 & 4 closed |
N/A |
N/A |
|
RTxC/RRxC |
Receive no clock |
All open |
All open |
N/A |
N/A |
|
RxD |
V.35 (RS-422) |
N/A |
N/A |
1 & 4 closed |
N/A |
|
RxD |
V.24 (RS-232) |
N/A |
N/A |
2 & 5 closed |
N/A |
|
RxD |
Current Loop |
N/A |
N/A |
3 & 6 closed |
N/A |
|
TTxC |
TRxCA |
Open |
N/A |
N/A |
1 & 3 closed |
|
TTxC |
RTxCA |
N/A |
Open |
N/A |
2 & 4 closed |
|
TTxC |
Send no clock |
N/A |
N/A |
N/A |
All open |
|
INTERFACE CONFIGURATION | |
|
Setting |
J12 |
|
RS-232 |
Pins 1 & 16, 2 & 17, 5 & 20, 6 & 21, 7 & 22, 9 & 24, 10 & 25, 11 & 26, 13 & 28, 14 & 29, 15 & 30 closed |
|
Note:If transmitting a clock, close pins 4 & 19. If receiving a clock, close pins 8 & 23 for RxC mode and close pins 12 & 27 for TxC mode. | |
|
INTERFACE CONFIGURATION | |
|
Setting |
J12 |
|
RS-422 |
Pins 1 & 16, 18 & 33, 5 & 20, 6 & 21, 26 & 41, 29 & 44, 30 & 45 closed |
|
Note:If transmitting a clock, close Pins 17 & 32, 19 & 34. If receiving a clock, close Pins 22 & 37, 23 & 38 for RxC mode and close Pins 24 & 39, 27 & 42 for TxC mode. | |
|
INTERFACE CONFIGURATION | |
|
Setting |
J12 |
|
Current Loop |
Pins 1 & 16, 2 & 17, 3 & 18, 7 & 22, 9 & 24, 11 & 40, 14 & 43, 14 & 29, 15 & 30 closed |
|
Note:If using positive voltage, close Pins 21 & 36. If using negative voltage, close Pins 20 & 35. | |