NATIONAL INSTRUMENTS
AT-MIO-16D
Card Type |
Analog to digital timing converter |
Chipset Controller |
Unidentified |
I/O Options |
Analog input, analog output, digital input, digital output |
Maximum DRAM |
N/A |
CONNECTIONS | |||
Purpose |
Location |
Purpose |
Location |
34-pin interface connector |
J1 |
100-pin I/O connector |
J2 |
BASE I/O ADDRESS SELECTION | ||||||
Address |
U61/A5 |
U61/A6 |
U61/A7 |
U61/A8 |
U61/A9 | |
220h |
Off |
On |
On |
On |
Off | |
100h |
On |
On |
On |
Off |
On | |
120h |
Off |
On |
On |
Off |
On | |
140h |
On |
Off |
On |
Off |
On | |
160h |
Off |
Off |
On |
Off |
On | |
180h |
On |
On |
Off |
Off |
On | |
360h |
Off |
Off |
On |
Off |
Off | |
380h |
On |
On |
Off |
Off |
Off | |
3A0h |
Off |
On |
Off |
Off |
Off | |
3C0h |
On |
Off |
Off |
Off |
Off | |
3E0h |
Off |
Off |
Off |
Off |
Off | |
Note: A total of 255 base address settings are available. The switches are a binary representation of the decimal memory addresses. Switch A9 is the Most Significant Bit and switch A5 is the Least Significant Bit. The switches have the following decimal values: switch A9=512, A8=256, A7=128, A6=64, A5=32. Turn On the switches and add the values of the switches that are On to obtain the correct memory address. (Off=1, On=0) |
DMA CHANNEL SELECTION (DMA 1) | |||||||
DMA |
W12/A |
W12/B |
W12/C |
W12/D |
W12/E |
W12/F | |
6 |
Open |
Open |
Pins 1 & 2 |
Pins 1 & 2 |
Open |
Open | |
5 |
Open |
Open |
Open |
Open |
Pins 1 & 2 |
Pins 1 & 2 | |
7 |
Pins 1 & 2 |
Pins 1 & 2 |
Open |
Open |
Open |
Open | |
Disabled |
Open |
Open |
Open |
Open |
Open |
Open | |
Note: Pins designated are in the closed position. |
DMA CHANNEL SELECTION (DMA 2) | |||||||
DMA |
W12/A |
W12/B |
W12/C |
W12/D |
W12/E |
W12/F | |
7 |
Pins 2 & 3 |
Pins 2 & 3 |
Open |
Open |
Open |
Open | |
5 |
Open |
Open |
Open |
Open |
Pins 2 & 3 |
Pins 2 & 3 | |
6 |
Open |
Open |
Pins 2 & 3 |
Pins 2 & 3 |
Open |
Open | |
Disabled |
Open |
Open |
Open |
Open |
Open |
Open | |
Note: Pins designated are in the closed position. |
INTERRUPT SELECTION (MIO-16 CIRCUITRY) | |||||||
IRQ |
W13/A |
W13/B |
W13/C |
W13/D |
W13/E |
W13/F | |
10 |
Open |
Open |
Open |
Open |
Open |
Open | |
2/9 |
Open |
Open |
Open |
Open |
Open |
1 & 2 | |
3 |
1 & 2 |
Open |
Open |
Open |
Open |
Open | |
4 |
Open |
1 & 2 |
Open |
Open |
Open |
Open | |
5 |
Open |
Open |
1 & 2 |
Open |
Open |
Open | |
6 |
Open |
Open |
Open |
1 & 2 |
Open |
Open | |
7 |
Open |
Open |
Open |
Open |
1 & 2 |
Open | |
11 |
Open |
Open |
Open |
Open |
Open |
Open | |
12 |
Open |
Open |
Open |
Open |
Open |
Open | |
14 |
Open |
Open |
Open |
Open |
Open |
Open | |
15 |
Open |
Open |
Open |
Open |
Open |
Open | |
Disabled |
Open |
Open |
Open |
Open |
Open |
Open | |
Note: Pins designated are in the closed position. |
INTERRUPT SELECTION (MIO-16 CIRCUITRY CONT) | ||||||
IRQ |
W13/G |
W13/H |
W13/I |
W13/J |
W13/K | |
10 |
Closed |
Open |
Open |
Open |
Open | |
2/9 |
Open |
Open |
Open |
Open |
Open | |
3 |
Open |
Open |
Open |
Open |
Open | |
4 |
Open |
Open |
Open |
Open |
Open | |
5 |
Open |
Open |
Open |
Open |
Open | |
6 |
Open |
Open |
Open |
Open |
Open | |
7 |
Open |
Open |
Open |
Open |
Open | |
11 |
Open |
Closed |
Open |
Open |
Open | |
12 |
Open |
Open |
Closed |
Open |
Open | |
14 |
Open |
Open |
Open |
Closed |
Open | |
15 |
Open |
Open |
Open |
Open |
Closed | |
Disabled |
Open |
Open |
Open |
Open |
Open | |
Note: Pins designated are in the closed position. |
INTERRUPT SELECTION (DIO -24 CIRCUITRY) | |||||||
IRQ |
W13/A |
W13/B |
W13/C |
W13/D |
W13/E |
W13/F | |
5 |
Open |
Open |
2 & 3 |
Open |
Open |
Open | |
2/9 |
Open |
Open |
Open |
Open |
Open |
2 & 3 | |
3 |
2 & 3 |
Open |
Open |
Open |
Open |
Open | |
4 |
Open |
2 & 3 |
Open |
Open |
Open |
Open | |
6 |
Open |
Open |
Open |
2 & 3 |
Open |
Open | |
7 |
Open |
Open |
Open |
Open |
2 & 3 |
Open | |
10 |
Open |
Open |
Open |
Open |
Open |
Open | |
11 |
Open |
Open |
Open |
Open |
Open |
Open | |
12 |
Open |
Open |
Open |
Open |
Open |
Open | |
14 |
Open |
Open |
Open |
Open |
Open |
Open | |
15 |
Open |
Open |
Open |
Open |
Open |
Open | |
Disabled |
Open |
Open |
Open |
Open |
Open |
Open | |
Note: Pins designated are in the closed position. |
INTERRUPT SELECTION (DIO-24 CIRCUITRY CONT) | ||||||
IRQ |
W13/G |
W13/H |
W13/I |
W13/J |
W13/K | |
5 |
Open |
Open |
Open |
Open |
Open | |
2/9 |
Open |
Open |
Open |
Open |
Open | |
3 |
Open |
Open |
Open |
Open |
Open | |
4 |
Open |
Open |
Open |
Open |
Open | |
6 |
Open |
Open |
Open |
Open |
Open | |
7 |
Open |
Open |
Open |
Open |
Open | |
10 |
Closed |
Open |
Open |
Open |
Open | |
11 |
Open |
Closed |
Open |
Open |
Open | |
12 |
Open |
Open |
Closed |
Open |
Open | |
14 |
Open |
Open |
Open |
Closed |
Open | |
15 |
Open |
Open |
Open |
Open |
Closed | |
Disabled |
Open |
Open |
Open |
Open |
Open | |
Note: Pins designated are in the closed position. |
DIO-24 CIRCUITRY INTERRUPT ENABLED CONFIGURATION | |||||
Setting |
W14/A |
W14/B |
W14/C |
W14/D | |
PC4 |
Open |
Closed |
Open |
Open | |
PC2 |
Open |
Open |
Closed |
Open | |
PC6 |
Closed |
Open |
Open |
Open | |
N/C (Disabled) |
Open |
Open |
Open |
Closed |
ANALOG INPUT CONFIGURATION | |||
Type |
W6 |
W9 | |
DIFF |
Pins 1 & 3, 2 & 4, 5 & 6 closed |
Pins 1 & 2 closed | |
RSE |
Pins 1 & 2, 3 & 4, 7 & 8 closed |
Pins 2 & 3 closed | |
NRSE |
Pins 1 & 2, 3 & 5, 7 & 8 closed |
Pins 2 & 3 closed |
ANALOG INPUT POLARITY & RANGE CONFIGURATION | ||||
Range |
Polarity |
W1 |
W4 | |
-10 to +10V |
Bipolar input |
Pins 1 & 2 closed |
Pins 2 & 3 closed | |
0 to +10V |
Unipolar input |
Pins 2 & 3 closed |
Pins 1 & 2 closed | |
-5 to +5V |
Bipolar input |
Pins 2 & 3 closed |
Pins 2 & 3 closed |
ANALOG OUTPUT CONFIGURATION | |||
Type |
W2 (Channel 1) |
W3 (Channel 0) | |
Internal |
Pins 2 & 3 closed |
Pins 2 & 3 closed | |
External |
Pins 1 & 2 closed |
Pins 1 & 2 closed |
ANALOG OUTPUT POLARITY CONFIGURATION | |||
Type |
W7 (Channel 1) |
W8 (Channel 0) | |
Bipolar |
Pins 1 & 2 closed |
Pins 1 & 2 closed | |
Unipolar |
Pins 2 & 3 closed |
Pins 2 & 3 closed | |
Note: Use this table in conjunction with the table below to set jumpers for Bipolar & Unipolar mode selection. |
BIPOLAR & UNIPOLAR OUTPUT MODE CONFIGURATION | |||
Mode |
W10 (Channel 0) |
W11 (Channel 1) | |
Twos Complement |
Pins 1 & 2 closed |
Pins 1 & 2 closed | |
Straight Binary (Unipolar) |
Pins 2 & 3 closed |
Pins 2 & 3 closed | |
Note: Bipolar can use both modes, while Unipolar uses the straight binary mode only. |
RTSI BUS CLOCK CONFIGURATION | ||||
Setting |
W5/A |
W5/B |
W5/C | |
Use local oscillator board signal |
Open |
Closed |
Closed | |
Receive the RTSI bus signal |
Closed |
Open |
Closed | |
Drive RTSI bus & board/OSC |
Closed |
Closed |
Open |