IPTool.net.ua IPTools.net.ua

AT-DIO-32F

NATIONAL INSTRUMENTS

AT-DIO-32F

Card Type

Parallel & Digital I/O card

Chipset Controller

Unidentified

I/O Options

32 lines of digital I/O (four 8-bit ports)

Maximum DRAM

N/A

CONNECTIONS

Purpose

Location

50-pin I/O interface connector

J1

BASE I/O ADDRESS SELECTION

Address

U61/A5

U61/A6

U61/A7

U61/A8

U61/A9

240h

On

Off

On

On

Off

 

000h

On

On

On

On

On

 

020h

Off

On

On

On

On

 

040h

On

Off

On

On

On

 

060h

Off

Off

On

On

On

 

080h

On

On

Off

On

On

 

360h

Off

Off

On

Off

Off

 

380h

On

On

Off

Off

Off

 

3A0h

Off

On

Off

Off

Off

 

3C0h

On

Off

Off

Off

Off

 

3E0h

Off

Off

Off

Off

Off

Note: A total of 255 base address settings are available. The switches are a binary representation of the decimal memory addresses. Switch A9 is the Most Significant Bit and switch A5 is the Least Significant Bit. The switches have the following decimal values: switch A9=512, A8=256, A7=128, A6=64, A5=32. Turn off the switches and add the values of the switches that are off to obtain the correct memory address. (Off=1, On=0)

DMA CHANNEL SELECTION (GROUP 1)

DMA

W1/A

W1/B

W1/C

W1/D

W1/E

W1/F

5

Pins 1 & 2

Pins 1 & 2

Open

Open

Open

Open

 

6

Open

Open

Pins 1 & 2

Pins 1 & 2

Open

Open

 

7

Open

Open

Open

Open

Pins 1 & 2

Pins 1 & 2

Note: Pins designated are in the closed position.

DMA CHANNEL SELECTION (GROUP 2)

DMA

W1/A

W1/B

W1/C

W1/D

W1/E

W1/F

6

Open

Open

Pins 2 & 3

Pins 2 & 3

Open

Open

 

5

Pins 2 & 3

Pins 2 & 3

Open

Open

Open

Open

 

7

Open

Open

Open

Open

Pins 2 & 3

Pins 2 & 3

Note: Pins designated are in the closed position.

INTERRUPT SELECTION (INTR 1)

IRQ

W2/A

W2/B

W2/C

W2/D

W2/E

W2/F

W2/G

W2/H

W2/I

W2/J

W2/K

11

Open

Open

Open

Open

Open

Open

Open

1 & 2

Open

Open

Open

 

2/9

Open

Open

Open

Open

Open

1 & 2

Open

Open

Open

Open

Open

 

3

1 & 2

Open

Open

Open

Open

Open

Open

Open

Open

Open

Open

 

4

Open

1 & 2

Open

Open

Open

Open

Open

Open

Open

Open

Open

 

5

Open

Open

1 & 2

Open

Open

Open

Open

Open

Open

Open

Open

 

6

Open

Open

Open

1 & 2

Open

Open

Open

Open

Open

Open

Open

 

7

Open

Open

Open

Open

1 & 2

Open

Open

Open

Open

Open

Open

 

10

Open

Open

Open

Open

Open

Open

1 & 2

Open

Open

Open

Open

 

12

Open

Open

Open

Open

Open

Open

Open

Open

1 & 2

Open

Open

 

14

Open

Open

Open

Open

Open

Open

Open

Open

Open

1 & 2

Open

 

15

Open

Open

Open

Open

Open

Open

Open

Open

Open

Open

1 & 2

Note: Pins designated are in the closed position.

INTERRUPT SELECTION (INTR 2)

IRQ

W2/A

W2/B

W2/C

W2/D

W2/E

W2/F

W2/G

W2/H

W2/I

W2/J

W2/K

12

Open

Open

Open

Open

Open

Open

Open

Open

2 & 3

Open

Open

 

2/9

Open

Open

Open

Open

Open

2 & 3

Open

Open

Open

Open

Open

 

3

2 & 3

Open

Open

Open

Open

Open

Open

Open

Open

Open

Open

 

4

Open

2 & 3

Open

Open

Open

Open

Open

Open

Open

Open

Open

 

5

Open

Open

2 & 3

Open

Open

Open

Open

Open

Open

Open

Open

 

6

Open

Open

Open

2 & 3

Open

Open

Open

Open

Open

Open

Open

 

7

Open

Open

Open

Open

2 & 3

Open

Open

Open

Open

Open

Open

 

10

Open

Open

Open

Open

Open

Open

2 & 3

Open

Open

Open

Open

 

11

Open

Open

Open

Open

Open

Open

Open

2 & 3

Open

Open

Open

 

14

Open

Open

Open

Open

Open

Open

Open

Open

Open

2 & 3

Open

 

15

Open

Open

Open

Open

Open

Open

Open

Open

Open

Open

2 & 3

Note: Pins designated are in the closed position.

RTSI BUS CLOCK CONFIGURATION

Setting

W3/A

W3/B

W3/C

Use local oscillator board signal

Closed

Closed

Open

 

Receive the RTSI bus signal

Closed

Open

Closed

 

Drive RTSI bus & board/OSC

Open

Closed

Closed