AMERICAN DATA AQUISITION CORPORATION
5500MF
|
Card Type |
Data Aquisition |
|
Chip Set |
Unidentified |
|
Maximum Onboard Memory |
Unidentified |
|
I/O Options |
Analog input, digital input |
|
Hard Drives supported |
None |
|
Floppy drives supported |
None |
|
Data Bus |
8-bit ISA |
|
Card Size |
Half length |
|
CONNECTIONS | |||
|
Function |
Label |
Function |
Label |
|
37-pin analog/digital signals connector |
J1 |
Bipolar offset selector |
P2 |
|
A/D converter gain selector |
P1 |
Unipolar offset selector |
P3 |
|
USER CONFIGURABLE SETTINGS | |||
|
Function |
Label |
Position | |
|
1.02 MHz PIT clock 1 input |
JP8 |
Pins 1 & 2 closed | |
|
External PIT clock 1 input |
JP8 |
Pins 2 & 3 closed | |
|
Factory configured - do not alter |
JP11 |
Open | |
|
A/D channel not sequenced |
JP12 |
Open | |
|
A/D channel auto sequenced |
JP12 |
Closed | |
|
DIGITAL INPUT/OUTPUT SELECTION | |||
|
Setting |
Label |
Position | |
|
Digital I/O inputs (0-3) |
JP4 |
Open | |
|
Digital I/O outputs (0-3) |
JP4 |
Closed | |
|
Digital I/O inputs (4-7) |
JP5 |
Open | |
|
Digital I/O outputs (4-7) |
JP5 |
Closed | |
|
Digital I/O outputs (8-11) |
JP6 |
Closed | |
|
Digital I/O inputs (8-11) |
JP6 |
Open | |
|
Digital I/O outputs (12-15) |
JP7 |
Closed | |
|
Digital I/O inputs (12-15) |
JP7 |
Open | |
|
A/D TRIGGER SOURCE SELECTION | |
|
Source |
JP1 |
|
Software trigger only |
Open |
|
External trigger |
Pins 1 & 2 closed |
|
PIT counter 0 trigger |
Pins 2 & 3 closed |
|
A/D RANGE SELECTION | ||||||
|
Polarity |
Voltage |
JP2 |
JP3 |
JP9 |
JP10 | |
|
Bipolar |
+ 10V |
Pins 1 & 2 |
Pins 1 & 2 |
Pins 1 & 2 |
Pins 1 & 2 | |
|
Bipolar |
+ 5V |
Pins 1 & 2 |
Pins 1 & 2 |
Pins 2 & 3 |
Pins 1 & 2 | |
|
Unipolar |
0-10V |
Pins 2 & 3 |
Pins 2 & 3 |
Pins 2 & 3 |
Pins 2 & 3 | |
|
Note: Pins designated are in the closed position | ||||||
|
BASE I/O ADDRESS SELECTION | |||||||
|
Setting |
W9 |
W8 |
W7 |
W6 |
W5 |
W4 | |
|
000h |
Closed |
Closed |
Closed |
Closed |
Closed |
Closed | |
|
010h |
Closed |
Closed |
Closed |
Closed |
Closed |
Open | |
|
020h |
Closed |
Closed |
Closed |
Closed |
Open |
Closed | |
|
030h |
Closed |
Closed |
Closed |
Closed |
Open |
Open | |
|
040h |
Closed |
Closed |
Closed |
Open |
Closed |
Closed | |
|
200h |
Open |
Closed |
Closed |
Closed |
Closed |
Closed | |
|
3B0h |
Open |
Open |
Open |
Closed |
Open |
Open | |
|
3C0h |
Open |
Open |
Open |
Open |
Closed |
Closed | |
|
3D0h |
Open |
Open |
Open |
Open |
Closed |
Open | |
|
3E0h |
Open |
Open |
Open |
Open |
Open |
Closed | |
|
3F0h |
Open |
Open |
Open |
Open |
Open |
Open | |
|
Note: A total of 256 base address settings are available. The jumpers are a binary representation of the decimal memory addresses. W9 is the Most Significant Bit and switch W4 is the Least Significant Bit. The switches have the following decimal values: W9=512, W8=256, W7=128, W6=64, W5=32, W4=16. Turn off the switches and add the values of the switches to obtain the correct memory address. (Close=0, Open=1) | |||||||