ACQUTEK CORPORATION
PM-9008
|
Card Type |
Solid-state disk |
|
Chipset |
Unidentified |
|
Maximum Onboard Memory |
2MB SRAM/8MB Flash ROM or EPROM |
|
Data Bus |
8-bit ISA |
|
CONNECTIONS | |
|
Function |
Label |
|
External battery connector (see pinout below) |
JP1 |
|
JP1 PINOUT | |||
|
Function |
Pin |
Function |
Pin |
|
Battery positive in |
1 |
Battery negative to ground |
3 |
|
Battery positive in |
2 |
Battery negative to ground |
4 |
|
USER CONFIGURABLE SETTINGS | |||
|
Setting |
Label |
Position | |
|
On-board battery enabled |
JP2 |
Closed | |
|
On-board battery disabled |
JP2 |
Open | |
|
Shared memory address set to D0000h |
JP3 |
Closed | |
|
Shared memory address set to DC000h |
JP3 |
Open | |
|
Base I/O address set to 200h |
JP4 |
Closed | |
|
Base I/O address set to 380h |
JP4 |
Open | |
|
SRAM is not write protected |
JP5 |
Open | |
|
SRAM is write protected |
JP5 |
Closed | |
|
Chip M1 contains SRAM |
SW1/1 |
On | |
|
Chip M1 contains EPROM or Flash ROM |
SW1/1 |
Off | |
|
Chip M2 contains SRAM |
SW1/2 |
On | |
|
Chip M2 contains EPROM or Flash ROM |
SW1/2 |
Off | |
|
Chip M3 contains SRAM |
SW1/3 |
On | |
|
Chip M3 contains EPROM or Flash ROM |
SW1/3 |
Off | |
|
Chip M4 contains SRAM |
SW1/4 |
On | |
|
Chip M4 contains EPROM or Flash ROM |
SW1/4 |
Off | |
|
USER CONFIGURABLE SETTINGS (CONT) | ||
|
Setting |
Label |
Position |
|
Chip M5 contains SRAM |
SW1/5 |
On |
|
Chip M5 contains EPROM or Flash ROM |
SW1/5 |
Off |
|
Chip M6 contains SRAM |
SW1/6 |
On |
|
Chip M6 contains EPROM or Flash ROM |
SW1/6 |
Off |
|
Chip M7 contains SRAM |
SW1/7 |
On |
|
Chip M7 contains EPROM or Flash ROM |
SW1/7 |
Off |
|
Chip M8 contains SRAM |
SW1/8 |
On |
|
Chip M8 contains EPROM or Flash ROM |
SW1/8 |
Off |
|
Chip M9 contains SRAM |
SW3/1 |
On |
|
Chip M9 contains EPROM or Flash ROM |
SW3/1 |
Off |
|
Chip M10 contains SRAM |
SW3/2 |
On |
|
Chip M10 contains EPROM or Flash ROM |
SW3/2 |
Off |
|
Chip M11 contains SRAM |
SW3/3 |
On |
|
Chip M11 contains EPROM or Flash ROM |
SW3/3 |
Off |
|
Chip M12 contains SRAM |
SW3/4 |
On |
|
Chip M12 contains EPROM or Flash ROM |
SW3/4 |
Off |
|
Chip M13 contains SRAM |
SW3/5 |
On |
|
Chip M13 contains EPROM or Flash ROM |
SW3/5 |
Off |
|
Chip M14 contains SRAM |
SW3/6 |
On |
|
Chip M14 contains EPROM or Flash ROM |
SW3/6 |
Off |
|
Chip M15 contains SRAM |
SW3/7 |
On |
|
Chip M15 contains EPROM or Flash ROM |
SW3/7 |
Off |
|
Chip M16 contains SRAM |
SW3/8 |
On |
|
Chip M16 contains EPROM or Flash ROM |
SW3/8 |
Off |
|
DRIVE SELECTION | |||||
|
Setting |
SW2/1 |
SW2/2 |
SW2/3 |
SW2/4 | |
|
A: |
On |
Off |
Off |
Off | |
|
B: |
Off |
On |
Off |
Off | |
|
C: |
Off |
Off |
On |
Off | |
|
D: |
Off |
Off |
Off |
On | |
|
Disabled |
Off |
Off |
Off |
Off | |
|
MEMORY CONFIGURATION |
|
The memory sockets (M1 - M16) on the PM-9008 accept SRAM chips (62010), EPROM chips (27010, 27020, or 27040), and Flash EPROM chips (28F010, 28F020, or 28F040). The Sockets can be filled in any order and SRAM chips can be mixed with either EPROMs or Flash EPROMs, however all EPROM or Flash EPROM must be the same size (i.e. all 27010 chips or all 28F040 chips). |