SILICON VALLEY COMPUTER, INC.
ADP70LB
|
|
|
Data bus: |
16-bit, ISA |
|
Size: |
Half-length, full-height card |
|
Hard drive supported: |
Two IDE (AT) Interface drives |
|
Floppy drives supported: |
Two 360KB, 720KB, 1.2MB, or 1.44MB drives |
|
CONNECTIONS | |
|
Function |
Location |
|
40-pin IDE (AT) interface connector |
P1 |
|
4-pin connector - drive active LED |
P2 |
|
5-pin connector - DC power |
P3 |
|
34-pin control cable connector - floppy drive |
P4 |
|
10-pin serial port 2 (COM2/4) - internal |
P5 |
|
16-pin game port - internal |
P6 |
|
10-pin serial port 1 (COM1/3) - external |
J4 |
|
25-pin parallel port (LPT1/2) - external |
J5 |
|
USER CONFIGURABLE SETTINGS | |||
|
Function |
Location |
Setting | |
|
Floppy drive enabled |
E7 |
Pins 2 & 3 closed | |
|
Floppy drive disabled |
E7 |
Pins 1 & 2 closed | |
|
Hard drive enabled |
E8 |
Pins 2 & 3 closed | |
|
Hard drive disabled |
E8 |
Pins 1 & 2 closed | |
|
Factory configured - do not alter |
SW1/1 |
N/A | |
|
SERIAL PORT 1 (J4) CONFIGURATION | |||
|
COM/Address |
E1 |
E2 | |
|
COM1/3E8h |
Pins 2 & 3 closed |
Pins 2 & 3 closed | |
|
COM3/3F8h |
Pins 2 & 3 closed |
Pins 1 & 2 closed | |
|
Disabled |
Pins 1 & 2 closed |
N/A | |
|
SERIAL PORT 2 (P5) CONFIGURATION | |||
|
COM/Address |
E3 |
E4 | |
|
COM2/2F8h |
Pins 2 & 3 closed |
Pins 2 & 3 closed | |
|
COM4/2E8h |
Pins 2 & 3 closed |
Pins 1 & 2 closed | |
|
Disabled |
Pins 1 & 2 closed |
N/A | |
|
PARALLEL PORT (J5) CONFIGURATION | |||
|
LPT/Address |
E5 |
E6 | |
|
LPT2/378h |
Pins 2 & 3 closed |
Pins 2 & 3 closed | |
|
LPT3/278h |
Pins 2 & 3 closed |
Pins 1 & 2 closed | |
|
Disabled |
Pins 1 & 2 closed |
N/A | |
|
ONBOARD BIOS | ||||
|
Address |
SW1/2 |
SW1/3 |
SW1/4 | |
|
Disabled |
Off |
Off |
Off | |
|
D8000h - D9FFFh |
On |
On |
On | |
|
D4000h - D5FFFh |
On |
On |
Off | |
|
D2000h - D3FFFh |
On |
Off |
On | |
|
D0000h - D1FFFh |
On |
Off |
Off | |
|
CC000h - CDFFFh |
Off |
On |
On | |
|
CA000h - CBFFFh |
Off |
On |
Off | |
|
C8000h - C9FFFh |
Off |
Off |
On | |
|
Note: (1) HDD type number must be set to 1 if ADP70LB BIOS is used. (2) Manufacturer recommends using system BIOS if possible. | ||||