PINE TECHNOLOGY
PT-606G
|
| |
|
Data bus: |
16-bit ISA |
|
Size: |
Half-length, full-height card |
|
Hard drive supported: |
Two IDE(AT) drives |
|
Floppy drives supported: |
Two 360KB, 720KB, 1.2MB, or 1.44MB drives |
|
CONNECTIONS | |
|
Function |
Location |
|
16-pin game port |
CN1 |
|
40-pin IDE(AT) connector |
CN2 |
|
34-pin cable connector - floppy drive |
CN3 |
|
9-pin serial port 1 - external |
CN4 |
|
10-pin serial port 2 - internal |
CN5 |
|
25-pin parallel port - external |
CN6 |
|
2-pin connector - drive active LED |
JP2 |
|
USER CONFIGURABLE SETTINGS | |||
|
Function |
Location |
Setting | |
|
IDE(AT) interface enabled |
J6 |
pins 2 & 3 closed | |
|
IDE(AT) interface disabled |
J6 |
pins 1 & 2 closed | |
|
Game port enabled |
J7 |
pins 1 & 2 closed | |
|
Game port disabled |
J7 |
pins 2 & 3 closed | |
|
Floppy drive interface enabled |
J9 |
pins 1 & 2 closed | |
|
Floppy drive interface disabled |
J9 |
pins 2 & 3 closed | |
|
USER CONFIGURABLE SETTINGS (CONTINUED) | |||
|
Function |
Location |
Setting | |
|
Hard drive is installed |
J10 |
pins 1 & 2 closed | |
|
Hard drive is not installed |
J10 |
pins 2 & 3 closed | |
|
Secure power source is in use by printer (standard current) |
JP3 |
closed | |
|
Low-end power source is in use by printer (isolate current) |
JP3 |
open | |
|
Note: The size and significance of jumper JP1 is unidentified. | |||
|
PARALLEL PORT ADDRESS SELECTION | ||||
|
LPT |
Address |
J1 |
J8 | |
|
LPT1 |
378h |
pins 1 & 2 closed |
pins 1 & 2 closed | |
|
LPT2 |
278h |
pins 1 & 2 closed |
pins 2 & 3 closed | |
|
Disable LPT1 |
N/A |
pins 2 & 3 closed |
pins 1 & 2 closed | |
|
Disable LPT2 |
N/A |
pins 2 & 3 closed |
pins 2 & 3 closed | |
|
SERIAL PORT ADDRESS SELECTION | ||||||
|
Port 1 (CN4) |
Port 2 (CN5) |
J2 |
J3 |
J4 |
J5 | |
|
COM1 |
COM2 |
pins 1 & 2 |
pins 1 & 2 |
pins 1 & 2 |
pins 1 & 2 | |
|
COM1 |
COM4 |
pins 1 & 2 |
pins 2 & 3 |
pins 1 & 2 |
pins 1 & 2 | |
|
COM3 |
COM2 |
pins 1 & 2 |
pins 1 & 2 |
pins 2 & 3 |
pins 1 & 2 | |
|
COM3 |
COM4 |
pins 1 & 2 |
pins 2 & 3 |
pins 2 & 3 |
pins 1 & 2 | |
|
COM1 |
Disabled |
pins 2 & 3 |
pins 1 & 2 |
pins 1 & 2 |
pins 1 & 2 | |
|
COM3 |
Disabled |
pins 2 & 3 |
pins 2 & 3 |
pins 2 & 3 |
pins 1 & 2 | |
|
Disabled |
COM2 |
pins 1 & 2 |
pins 1 & 2 |
pins 1 & 2 |
pins 2 & 3 | |
|
Disabled |
COM4 |
pins 1 & 2 |
pins 2 & 3 |
pins 1 & 2 |
pins 2 & 3 | |
|
Disabled |
Disabled |
pins 2 & 3 |
pins 1 & 2 |
pins 2 & 3 |
pins 2 & 3 | |
|
Note: Pins designated should be in the closed position. | ||||||