PERSTOR SYSTEMS, INC.
PS180-16FN
Data bus: 8-bit, ISA
Size: Full-length, full-height card
Hard drives supported: Two MFM or RLL ST506/ST412 drives or one of each
Floppy drives supported: None
Maximum heads/cyl.: 15 heads and 1024 cylinders
|
CONNECTIONS | |
|
Function |
Location |
|
34-pin control cable connector-hard drive |
CN1 |
|
20-pin data cable connector-drive 0 |
CN3 |
|
20-pin data cable connector-drive 1 |
CN4 |
|
34-pin control cable connector-hard drive |
CN5 |
|
4-pin connector-drive active LED |
CN6 |
|
USER CONFIGURABLE SETTINGS - ALL REVISIONS | |||
|
Function |
Location |
Setting | |
|
BIOS enabled |
JP1/jumper 1 |
closed | |
|
BIOS disabled |
JP1/jumper 1 |
open | |
|
USER CONFIGURABLE SETTINGS - REVISION 1.3 ONLY | |||
|
Function |
Location |
Setting | |
|
Hard drive port address is 1F0-1F7h |
JP3 |
closed | |
|
Hard drive port address is 170-177h |
JP3 |
open | |
|
Floppy drive enabled |
JP6 |
closed | |
|
Floppy drive disabled |
JP6 |
open | |
|
USER CONFIGURABLE SETTINGS - REVISION 2.2 ONLY | |||
|
Function |
Location |
Setting | |
|
Floppy drive port address is 3F0-3F7h |
JP4 |
pins 1 & 2 closed | |
|
Floppy drive port address is 370-377h |
JP4 |
pins 2 & 3 closed | |
|
Hard drive port address is 1F0-1F7h |
JP8 |
pins 1 & 2 closed | |
|
Hard drive port address is 170-177h |
JP8 |
pins 2 & 3 closed | |
|
Floppy drive enabled |
JP13 |
pins 1 & 2 closed | |
|
Floppy drive disabled |
JP13 |
pins 2 & 3 closed | |
|
BIOS ADDRESS | ||||||||
|
Address |
JP1/2 |
JP1/3 |
JP1/4 |
JP1/5 |
JP1/6 |
JP1/7 |
JP1/8 |
JP1/9 |
|
C400h |
closed |
open |
closed |
closed |
closed |
open |
open |
closed |
|
CA00h |
open |
closed |
open |
closed |
closed |
open |
open |
closed |
|
CC00h |
closed |
open |
open |
closed |
closed |
open |
open |
closed |
|
CE00h |
open |
open |
open |
closed |
closed |
open |
open |
closed |
|
D800h |
closed |
closed |
open |
open |
closed |
open |
open |
closed |
|
DC00h |
closed |
open |
open |
open |
closed |
open |
open |
closed |
|
DC00h |
open |
open |
open |
open |
closed |
open |
open |
closed |
|
MISCELLANEOUS TECHNICAL NOTES |
|
JP1/jumpers 2 through 9 are the BIOS address select. The factory setting is C800 and is set with trace wires at JP1/jumpers 2, 3, 5, 6, and 9. The BIOS address may be changed by cutting the traces and closing other pins, using the information in the table above. However any modifications to the controller will void the warranty! |