HEWLETT-PACKARD COMPANY
D2384-63031
|
| |
|
Data bus: |
16-bit ISA |
|
Size: |
Half-length, full-height card |
|
Hard drive supported: |
Two IDE(AT) drives |
|
Floppy drives supported: |
Two 360KB, 720KB, 1.2MB, or 1.44MB drives |
|
CONNECTIONS | |
|
Function |
Location |
|
9-pin serial port 1 - external |
CN1 |
|
25-pin parallel port - external |
CN2 |
|
40-pin IDE(AT) connector |
CN3 |
|
34-pin cable connector - floppy drive |
CN4 |
|
USER CONFIGURABLE SETTINGS | |||
|
Function |
Location |
Setting | |
|
Parallel port is LPT1 |
SW1/3 |
Closed | |
|
Parallel port is LPT2 |
SW1/3 |
Open | |
|
IDE(AT) primary address is 1F0h |
SW1/4 |
Closed | |
|
IDE(AT) secondary address is 170h |
SW1/4 |
Open | |
|
Floppy disk primary address is 3F0h |
SW1/5 |
Closed | |
|
Floppy disk secondary address is 370h |
SW1/5 |
Open | |
|
Serial Port enabled |
SW1/6 |
Closed | |
|
Serial Port disabled |
SW1/6 |
Open | |
|
Parallel port enabled |
SW1/7 |
Closed | |
|
Parallel port disabled |
SW1/7 |
Open | |
|
Note: Secondary Addresses for both floppy and IDE(AT) not supported. | |||
|
USER CONFIGURABLE SETTINGS (CONTINUED) | |||
|
Function |
Location |
Setting | |
|
IDE(AT) interface enabled |
SW1/8 |
Closed | |
|
IDE(AT) interface disabled |
SW1/8 |
Open | |
|
Floppy drive interface enabled |
SW1/9 |
Closed | |
|
Floppy drive interface disabled |
SW1/9 |
Open | |
|
Factory configured - do not alter |
SW1/10 |
N/A | |
|
SERIAL PORT ADDRESS SELECTION | |||
|
COM |
SW1/1 |
SW1/2 | |
|
COM1 |
Closed |
Closed | |
|
COM2 |
Open |
Closed | |
|
COM3 |
Closed |
Open | |
|
COM4 |
Open |
Open | |
|
SERIAL PORT INTERRUPT SELECTION | |||||
|
IRQ |
J2/1 |
J2/2 |
J2/3 |
J2/4 | |
|
IRQ4(COM1) |
Closed |
Open |
Open |
Open | |
|
IRQ3(COM2) |
Open |
Closed |
Open |
Open | |
|
IRQ10(COM3) |
Open |
Open |
Closed |
Open | |
|
IRQ11(COM4) |
Open |
Open |
Open |
Closed | |
|
Note: IRQ settings should correspond to switch settings 1 & 2. | |||||
|
PARALLEL PORT IRQ SELECTION | |||
|
IRQ/LPT |
J1/pins 1 & 2 |
J1/pins 3 & 4 | |
|
IRQ7(LPT1) |
Closed |
Open | |
|
IRQ5(LPT2) |
Open |
Closed | |
|
Note: IRQ settings should correspond to switch setting 3. | |||
|
MISCELLANEOUS TECHNICAL NOTES |
|
The location of SW1/1 and its open & closed positions are not identified. |