ADAPTEC, INC.
ACB-2322 (VERSION 1)
|
Data bus: |
16-bit, ISA |
|
Size: |
Full-length, full-height card |
|
Hard drive supported: |
Two RLL ESDI |
|
Floppy drives supported: |
Two 360KB, 720KB, 1.2MB, or 1.44MB drives |
|
CONNECTIONS | |
|
Function |
Location |
|
34-pin control cable connector - floppy drive |
J1 |
|
20-pin data cable connector - drive 2 |
J2 |
|
20-pin data cable connector - drive 1 |
J3 |
|
34-pin control cable connector - hard drive |
J4 |
|
4-pin connector - drive active LED |
J5 |
|
Serial monitor output |
J13 |
|
USER CONFIGURABLE SETTINGS | |||
|
Function |
Location |
Setting | |
|
|
Factory configured - do not alter |
J6 |
N/A |
|
|
Factory configured - do not alter |
J7 |
N/A |
|
|
Factory configured - do not alter |
J8 |
N/A |
|
|
Factory configured - do not alter |
J9 |
N/A |
|
|
Factory configured - do not alter |
J10 |
N/A |
|
|
BIOS address is C8000-CBFFFh |
J11 |
Pins 1 & 2 closed |
|
|
BIOS address is CC000-CFFFFh |
J11 |
Pins 2 & 3 closed |
|
|
BIOS disabled |
J11 |
All pins open |
|
|
Hard drive address is 1F0-1F7h |
J12/jumper A |
Open |
|
|
Hard drive address is 170-177h |
J12/jumper A |
Closed |
|
|
Floppy drive address is 3F0-3F7h |
J12/jumper B |
Open |
|
|
Floppy drive address is 370-377h |
J12/jumper B |
Closed |
|
|
Zero wait state enabled |
J12/jumper C |
Open |
|
|
Zero wait state disabled |
J12/jumper C |
Closed |
|
USER CONFIGURABLE SETTINGS | |||
|
Function |
Location |
Setting | |
|
|
Hard drive recal function enabled |
J12/jumper D |
Open |
|
|
Hard drive recal function disabled |
J12/jumper D |
Closed |
|
|
Factory configured - do not alter |
J12/jumper E |
N/A |
|
|
Serial monitor mode disabled |
J12/jumper F |
Open |
|
|
Serial monitor mode enabled |
J12/jumper F |
Closed |
|
|
Factory configured - do not alter |
J12/jumper G |
N/A |
|
|
Test point |
J14 |
All pins open |
|
|
Test point |
J15 |
Open |
|
|
Factory configured - do not alter |
J16 |
N/A |
|
|
Factory configured - do not alter |
J17 |
N/A |
|
|
Hard drive IRQ14 selected |
J18 |
Pins 1 & 2 closed |
|
|
Hard drive IRQ15 selected |
J18 |
Pins 2 & 3 closed |
|
|
Floppy drive DACK2 selected |
J19 |
Pins 1 & 2 closed |
|
|
Floppy drive DACK3 selected |
J19 |
Pins 2 & 3 closed |
|
|
Floppy drive IRQ6 selected |
J20 |
Pins 1 & 2 closed |
|
|
Floppy drive IRQ10 selected |
J20 |
Pins 2 & 3 closed |
|
|
Floppy drive DRQ3 selected |
J21 |
Pins 1 & 2 closed |
|
|
Floppy drive DRQ2 selected |
J21 |
Pins 2 & 3 closed |
|
Note:J18 pins 3 & 4 are not used and should never be closed. | |||