ADAPTEC, INC.
ACB-2372
|
Data bus: |
16-bit, ISA |
|
Size: |
Full-length, full-height card |
|
Hard drives supported: |
Two ST506/412, RLL drives |
|
Floppy drives supported: |
Two 360KB, 720KB, 1.2MB, 1.44MB drives |
|
CONNECTIONS | |
|
Function |
Location |
|
34-pin control cable connector-floppy drive |
CN1 |
|
20-pin data cable connector-drive 0 |
CN2 |
|
20-pin data cable connector-drive 1 |
CN3 |
|
34-pin control cable connector-hard drive |
CN4 |
|
4-pin connector-drive active LED |
CN5 |
|
Serial Monitor Output |
CN15 |
|
USER CONFIGURABLE SETTINGS | |||
|
Function |
Location |
Setting | |
|
|
Factory configured - do not alter |
JP6 through JP11 |
open |
|
|
BIOS address is C800h |
JP12 |
pins 1 & 2 closed |
|
|
BIOS address is CC00h |
JP12 |
pins 2 & 3 closed |
|
|
BIOS disabled |
JP12 |
open |
|
|
Factory configured - do not alter |
JP13 |
open |
|
|
Hard drive port address is 1F0-1F7h |
JP14/jumper 1 |
open |
|
|
Hard drive port address is 170-177h |
JP14/jumper 1 |
closed |
|
|
Floppy drive port address is 3F0-3F7h |
JP14/jumper 2 |
open |
|
|
Floppy drive port address is 370-377h |
JP14/jumper 2 |
closed |
|
|
One Wait State enabled |
JP14/jumper 3 |
open |
|
|
Zero Wait State enabled |
JP14/jumper 3 |
closed |
|
|
Drive Recal (Track 0 minus 1) enabled |
JP14/jumper 4 |
open |
|
|
Drive Recal (Track 0 minus 1) disabled |
JP14/jumper 4 |
closed |
|
|
Not Used |
JP14/jumper 5 |
open |
|
|
Serial Monitor Mode disabled |
JP14/jumper 6 |
open |
|
|
Serial Momitor Mode enabled (2400 Baud) |
JP14/jumper 6 |
closed |
|
|
Hard drive Interrupt is IRQ14 |
JP19 |
pins 1 & 2 closed |
|
|
Hard drive Interrupt is IRQ15 |
JP19 |
pins 2 & 3 closed |
|
|
Not Used |
JP19 |
pins 3 & 4 closed |
|
|
Floppy drive DMA Acknowledge Is DACK2 |
JP20 |
pins 1 & 2 closed |
|
|
Floppy drive DMA Acknowledge is DACK3 |
JP20 |
pins 2 & 3 closed |
|
|
Floopy drive Interrupt is IRQ6 |
JP21 |
pins 1 & 2 closed |
|
|
Floopy drive Interrupt is IRQ10 |
JP21 |
pins 2 & 3 closed |
|
|
Floppy drive DMA Request is DREQ2 |
JP22 |
pins 1 & 2 closed |
|
|
Floppy drive DMA Request is DREQ3 |
JP22 |
pins 2 & 3 closed |
|
|
Factory configured - do not alter |
JP23 |
N/A |